Parts for Kitchenaid KVIB606DBS3: Hood Parts

This hood damper mounts at the exhaust outlet to let cooking air exit while blocking backdrafts when the fan is off. Replacing a worn damper restores proper airflow and helps eliminate rattling or sticking during vent operation.

• Controls one-way airflow from the hood into the duct; seals when the fan is off
• Helps block outside air and moisture from entering through the vent
• Wear or damage can cause poor venting, rattling noises, or a stuck exterior flap
• Restores vent performance after the original damper is bent, warped, or missing

• Disconnect power at the breaker before servicing
• Access the exhaust outlet and remove the old damper; note airflow orientation
• Install so the flap swings freely and seats closed; avoid overtightening fasteners
• Run the fan to verify smooth damper movement and proper airflow

Replacement transformer that provides low-voltage power to the appliance control system, restoring reliable power to the control board and display. Use when the appliance is unresponsive or shows blank/noisy controls due to a failed transformer. What it does:

• Supplies the low-voltage power required by the control board and user interface.
• Enables control panel functions, displays, and relays that rely on the transformer.
• Common symptom: blank display or no response from touch/pressed controls.
• Also may cause intermittent operation or failure of electrically-driven features when faulty.

• Disconnect power (unplug or shut off breaker) before starting any work.
• Replace with the exact part number; match to the appliance wiring and mounting.
• Observe proper wiring, polarity, and secure connections; do not work on wet surfaces.

This insulation cabinet panel helps reduce heat transfer and dampen noise inside the appliance, supporting proper temperature control and more consistent cooling performance. Replace worn or damaged insulation to restore thermal protection and quiet operation. What it does:

• Provides thermal barrier between cabinet and interior to help maintain set temperatures
• Helps limit frost buildup on evaporator area by reducing air infiltration
• Reduces vibration and operating noise from compressor and airflow
• Supports overall cooling efficiency when installed intact and properly positioned

• Disconnect power and empty the appliance area before beginning any repair
• Remove interior liners or access panels as required to reach and replace the insulation
• Handle insulation carefully to avoid tearing; secure with factory clips or approved adhesive where originally installed

This electronic control board is the main console control that manages user inputs and appliance functions, restoring control and display operation for affected units. It replaces a failed or unresponsive main control module to regain normal electronic control. What it does

• Receives button and touchpad inputs and controls cycles, timers, and display functions
• Processes signals to switches, relays, and powered components to start and stop operations
• Helps resolve symptoms like an unlit or blank display, unresponsive buttons, or erratic cycle behavior
• Works with other components to clear intermittent faults caused by a failed control board

• One electronic control board (main console control)

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Handle the board by its edges and avoid touching electronic components; use anti-static precautions if possible
• Installation typically requires removal of the control or console panel and careful connector removal/reinstallation

This capacitor helps the appliance motor start and run more smoothly, restoring reliable motor operation and reducing hard-start symptoms. It's a direct-fit replacement when the original capacitor fails. What it does:

• Provides the initial electrical boost to start the motor and helps maintain stable motor operation
• Commonly replaces a failed or weak capacitor that causes the motor to hum, not start, stall, or run inconsistently
• Works with the appliance's existing control and motor components to restore normal performance
• Uses the same mounting and terminal layout as the original for a straightforward replacement

• Disconnect power to the appliance before inspecting or replacing the capacitor
• Discharge the capacitor before handling—capacitors can store a dangerous charge even when unplugged
• Take note of terminal locations or photograph wiring before removal to ensure correct reconnection

This electronic control board manages a washer or dryer's timed cycles and user interface, restoring proper electronic control and cycle selection for units with unresponsive or erratic controls. Replaces a failed main control assembly to regain normal operation. What it does:

• Receives input from buttons/knobs and sends signals to motors, valves, and heaters
• Controls cycle timing, displays, and diagnostics for correct program sequencing
• Commonly used when controls are unresponsive, display errors occur, or cycles stop mid-run
• Prevents erratic or unintended cycling caused by a damaged or shorted circuit board

• One electronic control board (main control assembly)

• Disconnect power before servicing to avoid shock or damage
• Handle the board by its edges and avoid touching components or contacts
• Verify connector orientation and secure all wire harnesses before reapplying power

The Clip is an OEM part for Whirlpool range hoods. It is a small but important component that helps securely hold portions of the range hood in place.

Symptoms of a bad clip can include wear and tear causing it to break or become loose over time, and failing to properly support attached parts. 

Causes of a bad clip include repeated opening and closing of the range hood putting stress on the clip, as well as damage from accidents.

Symptoms of a bad clip include:

• rattling or loose noises coming from the range hood 
• attached panels or pieces no longer staying fully secured
• gaps appearing where parts were formerly held tightly together

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement light bulb restores bright, reliable illumination inside your appliance so you can clearly see contents and settings. Replace it when the original bulb burns out, flickers, or the glass/filament is damaged. What it does

• Provides interior lighting when the door is opened or the light switch is activated
• Improves visibility for loading, unloading, and checking progress
• Common failure symptoms: no light, intermittent/flickering light, dim/blackened bulb, broken glass or filament

• 1 light bulb

• Disconnect power before servicing and allow the bulb/area to cool completely
• Wear gloves and eye protection; handle glass carefully
• Use the bulb type and wattage specified for your model; do not exceed the rating
• Install snugly without overtightening; restore power and test

The Blower Fan is an OEM replacement part for Whirlpool vent hoods. It is responsible for powering the fan that helps to effectively remove smoke, odors, and grease particles from your kitchen.

A bad vent hood blower fan motor can occur due to regular wear and tear, electrical malfunctions, or motor failure. If you notice symptoms such as a weak or noisy fan, reduced airflow, or complete failure of the fan motor, it may be time to replace it.

Symptoms of a bad vent hood blower fan motor include:

• Weak or noisy fan operation
• Reduced airflow or poor ventilation performance
• Complete failure of the fan motor

Restore proper ventilation and eliminate unwanted odors in your kitchen by replacing the faulty or malfunctioning vent hood blower fan motor with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This microwave charcoal filter captures cooking odors and smoke in recirculating setups to help keep air moving cleanly through the blower. Replace a saturated or damaged filter to maintain ventilation performance and minimize lingering smells.

• Adsorbs odors and smoke during non-vented operation
• Helps maintain airflow and keep internal surfaces cleaner
• Common signs it's due: persistent odors, reduced airflow, or a visibly dirty/damaged filter
• Intended for over-the-range microwaves that use a charcoal air filter

• Disconnect power to the microwave before servicing
• Remove the upper grille or access panel per your model; release and remove the old filter
• Install the new filter in the same orientation; reinstall grille and restore power

This name plate is the appliance's model and serial identification label—an easy way to restore clear product ID for service, parts ordering, and warranty records. Keeps your appliance information visible and readable. What it does:

• Displays manufacturer model and serial numbers and other factory ID details
• Restores a missing or damaged ID label so technicians can identify the correct parts and specs
• Helps when registering the appliance or filing warranty and service requests
• Prevents delays caused by unreadable or absent identification information

• Clean and dry the mounting surface before applying; remove old adhesive residue
• Align carefully and press firmly; some name plates use adhesive backing or mounting tabs
• Do not cover vents, controls, or safety labels when installing

This replacement light bulb restores interior illumination inside your appliance. Swap it in for a burned-out bulb so you can clearly see contents and monitor operation when the door opens or the light button is pressed.

• Provides interior light inside the appliance cavity
• Direct replacement for a failed or broken bulb
• Common symptoms: no light when the door opens, flickering/intermittent light, visibly darkened or broken bulb

• Disconnect power to the appliance before servicing
• Allow the old bulb and nearby surfaces to cool completely
• Remove any lens or cover to access the socket; install the new bulb in the same orientation as the original
• Handle with clean, dry hands or gloves; do not overtighten. Restore power and test