Parts for Whirlpool WVW7330JS0: Hood Parts

This hood damper mounts at the exhaust outlet to let cooking air exit while blocking backdrafts when the fan is off. Replacing a worn damper restores proper airflow and helps eliminate rattling or sticking during vent operation.

• Controls one-way airflow from the hood into the duct; seals when the fan is off
• Helps block outside air and moisture from entering through the vent
• Wear or damage can cause poor venting, rattling noises, or a stuck exterior flap
• Restores vent performance after the original damper is bent, warped, or missing

• Disconnect power at the breaker before servicing
• Access the exhaust outlet and remove the old damper; note airflow orientation
• Install so the flap swings freely and seats closed; avoid overtightening fasteners
• Run the fan to verify smooth damper movement and proper airflow

The Chimney Duct Assembly is an OEM part for Whirlpool range vent hoods. It is designed to provide a connection between the vent hood and the exterior ventilation system for airflow and removal of cooking odors and smoke.

A bad chimney duct assembly can occur due to regular use, wear and tear, or damage caused by external factors. If you notice poor ventilation, lingering odors, or smoke not being adequately expelled from your kitchen, it may indicate a problem with the chimney duct assembly.

Symptoms of a bad chimney duct assembly include:

• Insufficient airflow or poor ventilation
• Lingering cooking odors or smoke in the kitchen
• Excessive grease buildup in the vent hood or duct system

Replace your faulty chimney duct assembly with this genuine OEM part to restore your appliance. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This capacitor helps the appliance motor start and run more smoothly, restoring reliable motor operation and reducing hard-start symptoms. It's a direct-fit replacement when the original capacitor fails. What it does:

• Provides the initial electrical boost to start the motor and helps maintain stable motor operation
• Commonly replaces a failed or weak capacitor that causes the motor to hum, not start, stall, or run inconsistently
• Works with the appliance's existing control and motor components to restore normal performance
• Uses the same mounting and terminal layout as the original for a straightforward replacement

• Disconnect power to the appliance before inspecting or replacing the capacitor
• Discharge the capacitor before handling—capacitors can store a dangerous charge even when unplugged
• Take note of terminal locations or photograph wiring before removal to ensure correct reconnection

The Grease Filter is an OEM part for Whirlpool range hoods. This part traps grease particles from the air as it circulates through the range hood, preventing grease buildup on the blower and other internal components, thus maintaining the efficiency and longevity of the range hood.

Causes of a bad grease filter can include clogging from excessive grease accumulation, physical damage from improper cleaning or handling, and general wear and tear over time.

Symptoms of a bad grease filter include:

• Reduced air flow from the range hood
• Visible grease buildup on or around the filter
• Unusual odors persisting in the kitchen
• Filter appearing worn or damaged

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This blower-fan assembly circulates air through the appliance to aid efficient drying and proper airflow. Replacing a worn or damaged blower restores airflow and helps the unit reach normal operating temperatures. What it does:

• Moves air through the drum and exhaust system for drying and venting
• Helps maintain consistent heat distribution to improve drying performance
• Prevents overheating by ensuring proper airflow through the appliance
• Common symptoms of a failing blower: reduced or no airflow, longer dry times, loud rattling or grinding noises

• Disconnect power (unplug or shut off breaker) before starting any repair
• Basic disassembly of the cabinet or front panel may be required
• Inspect surrounding seals and ducts for obstructions or wear while replacing the blower
• If you hear unusual noises after installation, recheck fitment and mounting hardware