Huskee / Husky Snow Removal Equipment Parts

This part is a throttle control box assembly. The throttle controls the amount of air or fuel that enters the engine and also controls the speed of the engine. This assembly includes a throttle control knob that allows the user to control the throttle and the speed of the outdoor power equipment machine.A new throttle control box may be needed if any part of the assembly is cracked, broken, or damaged in any way. It's important to remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine MTD throttle control box assembly and is an OEM part sourced directly from the manufacturer and it is sold individually. This specific throttle control box assembly is compatible with edgers and lawn tractors that are manufactured by MTD, Yard Man, Yard Machines, and Cub Cadet.

This lower chute is a genuine MTD part, sold individually. This lower chute can be used as a replacement part in a snowblower. The purpose of the lower chute in a snowblower is to allow the dispensing of snow out of the way of the operator and out of the side or back of the snowblower while the appliance is in operation. The lower chute in a snowblower might have to be replaced if the snow can no longer be properly channeled through and then out of the chute while the snowblower is being driven across a snowy surface. If the lower chute is punctured, scraped, dented, cracked, warped, eroded, or otherwise damaged to the point that snow is clogged within it, cannot pass through it, or falls out of it while the snowblower is in use, the lower chute should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This lower chute is compatible with the following outdoor appliance brands: MTD, Craftsman, Troy-Bilt, Yard Machines, Huskee, and Yard Man.

This replacement part is a plug kit. This is a genuine replacement part made by MTD. Plug kits are a great tool that allows the user to repair punctured tires or wheels in different kinds of lawn mowers or other machinery. A new plug kit might be needed if the current one is no longer working properly. If the part no longer works to assist the user in filing tires or repairing a wheel, it would be a good idea to replace this part. Always make sure that the engine is powered down before attempting to repair a tire. Work gloves are also recommended in this situation. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This genuine replacement part is an air filter heating cover for snowblowers. The air filter heating pipe cover is the plastic piece that covers the heating pipe of a snowblower. This cover is meant to protect the user from burning themselves on the heating pipe while using the machine. If the heating pipe cover is damaged to the point where it is no longer covering the heating pipe, it should be replaced. Thankfully, replacing this part is a simple process.To replace the heating pipe cover, locate the mounting screws that secure it to the snowblower. Before removing, make sure the engine has cooled to avoid getting burned. Once located, remove the mounting screws that attach the cover. Once removed, replace with the new cover and fasten the screws tightly. This OEM replacement part is sold individually and is compatible with MTD brand snowblowers.

This replacement part is a cylinder head assembly. The cylinder head assembly covers the engine head cylinder and houses the cylinder valves. Over time, the cylinder head assembly can become damaged due to excessive wear and tear. If the engine is no longer running as efficiently as it once did, the cylinder head assembly might need to be replaced. Luckily, this is a fairly simple repair.Before beginning, make sure the engine of the mower has cooled. Once cool, begin by lifting up the hood or engine cover and detach it. Remove the air filter cover. Lift out the air filter. Using a three-eighths socket or wrench remove the blower housing mounting bolts. Detach the oil drain tube and lift off the blower housing. Unthread the bolts that secure the intake manifold and detach the breather tube. Set the carburetor assembly aside. Then unthread the spark plug. Remove the mounting bracket and unthread the exhaust manifold bolts. Pull the manifold free of the muffler. Unthread the valve cover mounting bolts. Pry the cover off with a putty knife and be prepared for some oil to spill. Once the cover is off use the three-eights inch socket wrench to remove the old cylinder head mounting bolts. Pull the old cylinder assembly out of its place and replace it with the new assembly.This genuine OEM part is compatible with MTD brand lawnmowers.

This replacement part is a flywheel. This is a genuine replacement part made by MTD. This part is a large rotating piece, similar to a wheel, that provides the engine with rotational energy that is later converted to other types of energy so that the engine can operate smoothly. A new flywheel might be needed if the current one is missing or damaged. If the user hears unusual noises coming from inside the engine area, the flywheel might be out of place and not working properly. If this is the case, it might be best to replace this part. Be sure the engine is completely powered down and cooled off before repairing this part. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This replacement part is a gasket kit, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. A gasket kit includes many different small parts that all work together to help the engine run smoothly. A gasket kit is typically held together using screw and bolts and is situated very close to the engine. A new gasket might be needed if the current one is visibly damaged or broken. It is not unusual for the gasket to become worn down after years or normal use. Be sure the entire engine is shut down and cooled off before replacing this part. It is also recommended that work gloves are used as some of the parts may be sharp.This is an OEM replacement part and is sold individually. This part is sourced directly from the manufacturer, and it is intended for use in different lawn mowers.

This carburetor gasket is located between the insulator and the carburetor, creating a strong seal between the two to allow for optimal compression and engine performance. Over time and due to constant heat exposure, gaskets can degrade or become damaged. This can result in leaks in the system, which will impact performance and could cause the engine to fail completely if not properly addressed. If the carburetor gasket becomes faulty in any capacity, it needs to be replaced as soon as possible. This genuine OEM gasket replacement is manufactured to exact standards and is compatible with several models of snowblower engines from Troy-Bilt, MTD, Yard Man, Yard Machines, Cub Cadet, and Husky. This gasket is made of durable material, but gaskets could be more prone to damage or breakage during other repairs, so always use caution when working with this part. Allow the engine to cool completely and wear gloves when performing any engine repairs for hand protection.

A carburetor gasket works by providing a secure seal, preventing leaking between the carburetor and the insulator plate. Over time, gaskets can become worn down, cracked, or torn. This affects the efficiency or your equipment’s engine. If your carburetor has a leak due to a damaged carburetor gasket, the engine may run roughly or not start at all. This repair should be easy and take only a short time. Remove the damaged carburetor gasket and replace it with a new genuine OEM part. A set of screwdrivers is needed to make this repair possible. The carburetor gasket will work with small engines like log splitters, snowblowers, and tillers. Some of the many brands that are compatible with this carburetor gasket are Craftsman, Cub Cadet, MTD, Troy-Bilt, Yard Machines, and Yard-Man. Sold individually.

This replacement part is a camshaft assembly. This is a genuine replacement part made by MTD. This part is a rotating metal object that converts rotational motion to reciprocal motion. This ensures that the machine is able to move successfully according to the user's preferences at any given time. A new camshaft assembly might be needed if the user notices the engine is not working up to the normal standard. This can be from a faulty camshaft assembly and should be replaced if this is the case. Be sure the engine is turned off before attempting this repair to ensure the safety of the user and those around them. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This replacement part is a piston pin. This is a genuine replacement part made by MTD. This part is small but important to ensure that the piston is working properly during use. A new piston pin might be needed if the current one is missing or damaged. It is not uncommon for the pin to be stripped down over time due to normal wear and tear. The pin may also become lodged in place and should be replaced if this happens. Wear work gloves when completing this repair to prevent injury during the job. The engine should be completely turned off and cooled down before beginning repairs.This part is sold individually and is sourced directly from the manufacturer. This is a genuine OEM replacement part.

This is an MTD rocker arm. The rocker arm works in conjunction with the engine and head. The job of the rocker arm is to push the intake valve open, allowing fuel and air to enter the cylinder. Since the rocker arm is a part of the head gasket system, any damage can cause the engine to run extremely weak. There could also be a noticeable clicking or ticking noise originating from the engine area of the mower. A visual inspection of the rocker arm will confirm any damage. Begin the repair by removing the muffler guard. After removal, move to the valve cover and remove that guard as well. Disconnect the fuel and air lines running to the head. Remove the spark plugs in the valve section. Finally, the rocker arm can be removed using a socket wrench. Repeat these steps in reverse to install the new rocker arm.This product is sourced directly from the manufacturer as a genuine OEM part. The component is available individually, separate from the original machine. This part is compatible with MTD and Cub Cadet brand equipment.

This part is a replacement intake valve seal. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. The intended use for this part is to properly replace a defective or worn intake valve seal in outdoor power equipment.The intake valve seal prevents leaks and seals the intake valve, which can be found inside the engine housing. Valve seals should be checked regularly and replaced if worn, brittle, broken, or ineffective in any way. Always ensure that the equipment is completely powered off and is cooled down before attempting to start the repair process. For more accurate information on the installation of this particular intake valve seal, reference the owner's manual or equipment diagrams for specific instructions and part location. This is an authentic OEM part and as such is sold individually and made from durable and high-quality materials. This intake valve seal can be used with a variety of outdoor power equipment models manufactured by MTD, Craftsman, and other brands.