Huskee / Husky Snow Removal Equipment Parts

This shave plate is a genuine MTD part, sold individually. This shave plate can be used as a replacement part in a snowblower. The purpose of the shave plate in a snowblower is to scrape up densely packed snow that might linger below the base of the appliance and get in the way of the operator while the snowblower is in use.The shave plate in a snowblower might need to be replaced if it can no longer efficiently and effectively serve its typical function. The shave plate might be dented, cracked, chipped, punctured, warped, or eroded and if this form of damage occurs, it should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is a genuine OEM from the manufacturer. It is sold individually. This shave plate is compatible with the following outdoor appliance brands: MTD.

This shave plate is a genuine MTD part, sold individually. This shave plate can be used as a replacement part in a snowblower. The purpose of the shave plate in a snowblower is to unpack densely packed blocks of ice and snow as the snowblower is in use.The shave plate in a snowblower might suffer damage that can warrant a full replacement of the component. This could occur if the shave plate has been dented, punctured, cracked, chipped, warped, eroded, or otherwise damaged. If this occurs, the shave plate should be removed and replaced by this genuine OEM replacement part in order to continue safe usage of the snowblower.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This shave plate is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Yard Machines, Huskee, and Yard Man.

This replacement clutch drive is a part of the drive system and wheel assembly on snowblowers. The clutch drive engages the transmission when the engine is turned on so that the snowblower auger will rotate as the machine is pushed forward. This part is subject to repetitive motion and constant use so it sometimes just wears down with regular use. If something gets into the snowblower auger or other areas, that could damage the clutch drive, as well. In the event there is damage or the clutch drive no longer works as it should, it will need to be replaced with an OEM part like this one. This is a genuine replacement part made to OEM standards. It can be used in compatible machines from MTD, Craftsman, Troy-Bilt, and Yard-Man. The clutch drive is sold individually. It will not contain any additional parts or components. Disconnect the power supply or disengage the engine before working on outdoor power equipment. Allow the unit to cool and be cautious working around the auger as the blades can be quite sharp.

This snow thrower frame cover is an authentic OEM replacement part sourced directly from the manufacturer for use on snow throwers to protect the drive system from debris and dirt while removing snow. If the snow thrower's frame cover is damaged or broken, the machine should not be used until it is replaced. During regularly scheduled inspections and at the start of each snow season, the snow thrower should be inspected for damage. If the snow thrower frame cover is damaged, replace it with this new part.Before replacing parts on the snow thrower, make sure the key is not in the ignition and that the spark plug is not in the machine. Remove any fuel in the machine so that doesn't leak when the machine is turned on its edge. Park the snow thrower on a flat surface and pivot it forward so that it is now resting on the auger housing. Locate the screws holding the thrower frame cover in place and remove them. Set them aside to use on the new snow thrower. Remove the damaged framed cover and replace it with the new one. Reinstall the screws and tighten. Refill the gas and reinstall the spark plug.This thrower frame is a red metal part that is sold individually. It does not come with the screws used to secure it. This thrower frame cover is designed for use on snow throwers manufactured by Husky, Yard Machines, MTD, Troy-Bilt, and Yard-Man.

This part is a throttle control box assembly. The throttle controls the amount of air or fuel that enters the engine and also controls the speed of the engine. This assembly includes a throttle control knob that allows the user to control the throttle and the speed of the outdoor power equipment machine.A new throttle control box may be needed if any part of the assembly is cracked, broken, or damaged in any way. It's important to remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine MTD throttle control box assembly and is an OEM part sourced directly from the manufacturer and it is sold individually. This specific throttle control box assembly is compatible with edgers and lawn tractors that are manufactured by MTD, Yard Man, Yard Machines, and Cub Cadet.

This lower chute is a genuine MTD part, sold individually. This lower chute can be used as a replacement part in a snowblower. The purpose of the lower chute in a snowblower is to allow the dispensing of snow out of the way of the operator and out of the side or back of the snowblower while the appliance is in operation. The lower chute in a snowblower might have to be replaced if the snow can no longer be properly channeled through and then out of the chute while the snowblower is being driven across a snowy surface. If the lower chute is punctured, scraped, dented, cracked, warped, eroded, or otherwise damaged to the point that snow is clogged within it, cannot pass through it, or falls out of it while the snowblower is in use, the lower chute should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This lower chute is compatible with the following outdoor appliance brands: MTD, Craftsman, Troy-Bilt, Yard Machines, Huskee, and Yard Man.

This replacement part is a plug kit. This is a genuine replacement part made by MTD. Plug kits are a great tool that allows the user to repair punctured tires or wheels in different kinds of lawn mowers or other machinery. A new plug kit might be needed if the current one is no longer working properly. If the part no longer works to assist the user in filing tires or repairing a wheel, it would be a good idea to replace this part. Always make sure that the engine is powered down before attempting to repair a tire. Work gloves are also recommended in this situation. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This genuine replacement part is an air filter heating cover for snowblowers. The air filter heating pipe cover is the plastic piece that covers the heating pipe of a snowblower. This cover is meant to protect the user from burning themselves on the heating pipe while using the machine. If the heating pipe cover is damaged to the point where it is no longer covering the heating pipe, it should be replaced. Thankfully, replacing this part is a simple process.To replace the heating pipe cover, locate the mounting screws that secure it to the snowblower. Before removing, make sure the engine has cooled to avoid getting burned. Once located, remove the mounting screws that attach the cover. Once removed, replace with the new cover and fasten the screws tightly. This OEM replacement part is sold individually and is compatible with MTD brand snowblowers.

This replacement part is a cylinder head assembly. The cylinder head assembly covers the engine head cylinder and houses the cylinder valves. Over time, the cylinder head assembly can become damaged due to excessive wear and tear. If the engine is no longer running as efficiently as it once did, the cylinder head assembly might need to be replaced. Luckily, this is a fairly simple repair.Before beginning, make sure the engine of the mower has cooled. Once cool, begin by lifting up the hood or engine cover and detach it. Remove the air filter cover. Lift out the air filter. Using a three-eighths socket or wrench remove the blower housing mounting bolts. Detach the oil drain tube and lift off the blower housing. Unthread the bolts that secure the intake manifold and detach the breather tube. Set the carburetor assembly aside. Then unthread the spark plug. Remove the mounting bracket and unthread the exhaust manifold bolts. Pull the manifold free of the muffler. Unthread the valve cover mounting bolts. Pry the cover off with a putty knife and be prepared for some oil to spill. Once the cover is off use the three-eights inch socket wrench to remove the old cylinder head mounting bolts. Pull the old cylinder assembly out of its place and replace it with the new assembly.This genuine OEM part is compatible with MTD brand lawnmowers.