Parts for Kenmore 795.79433210 (79579433210, 795 79433210): Ice Maker Parts

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This guide tube is a small routing sleeve that supports and protects a rod, shaft, cable, or line inside your appliance. It keeps the path straight to reduce friction, noise, and premature wear.

• Guides and supports a rod/shaft/cable/tube through the chassis
• Maintains alignment for smooth movement or flow
• Helps prevent chafing, kinks, and vibration-related damage
• Typical failure signs: scraping or rattling noises, binding/misalignment, or visible cracks/deformation

• Disconnect power; turn off water or gas before servicing
• Refer to your model's parts diagram for routing and mounting points
• Reuse original screws/clips unless damaged
• Route exactly like the original; avoid pinches/kinks and verify clearances before restoring power

This refrigerator ice maker assembly restores automatic ice production. It manages the fill, freeze, and harvest cycles so your freezer reliably makes and releases ice cubes into the bin.

• Produces and harvests ice cubes automatically
• Controls water fill and the freeze/eject timing for each cycle
• Pauses production when the bin is full
• Common fixes: no ice production, very low ice output, unit stuck mid-cycle, cubes not ejecting, or loud clicking from the ice maker module

• Unplug the refrigerator and turn off the water supply before servicing
• Match and seat the wire connector fully; do not force pins
• Reuse any original mounting brackets, covers, or ice-level arm if required by your model
• Align the fill tube with the ice maker fill cup; restore power and allow up to 24 hours for normal ice production

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

Replacement tube connector (mechanical) that secures and routes tubing in compatible LG appliances, helping restore proper fluid flow and reduce leaks from loose or damaged connections. A literal OEM-style connector used where a secure tube-to-component join is required. What it does:

• Joins and secures tubing to appliance components or chassis to maintain a stable connection
• Keeps tubing aligned to prevent kinks or dislodging that can interrupt flow
• Commonly replaced when you see dripping, visible leaks, loose tubing, or poor water flow
• Fits the original mounting interface for reliable mechanical retention

• Disconnect power and shut off the water supply before starting any repairs
• Inspect tubing and nearby fittings for damage; replace any compromised tubing before installing the connector
• Seat the connector fully and secure per the appliance's service instructions; avoid overtightening which can damage tubing
• After installation, restore water and power and check the connection for leaks during a short test cycle

This water inlet valve assembly controls the flow of water from your home's supply into the refrigerator for the dispenser and ice maker. Replacing a failed valve restores reliable filling and helps prevent leaks, no-dispense, and no-ice issues.

• Regulates and routes water to the ice maker and dispenser when energized by the control system
• Resolves: no water from dispenser, no ice production, slow fill, or intermittent dispensing
• Leaks or drips from the rear valve area or water line connections
• Continuous water flow or ice maker overfill caused by a valve stuck open

• Disconnect power and shut off the water supply before servicing
• Pull the refrigerator forward to access the rear; have a towel or pan ready for residual water
• Transfer each wire connector and water tube to the matching port on the new valve; ensure all fittings lock fully
• Restore water and power, then check connections for leaks and test dispenser/ice fill