Parts for Briggs & Stratton 137202-0714-A2: Kits / Gasket Sets - Engine Parts

This oil seal is a common part engineered to work in engines that power generators, vacuum cleaners, snowblowers, leaf blowers, mowers, and other small engine applications. The seal sits between the crankcase and the crankshaft. It is designed as a barrier to prevent oil leakage and to stop contaminants from leaving the crankcase. When the gasoline engine exhibits diminished power, and especially if it begins to emit oily gray or bluish smoke, there is a good chance the oil seal needs to be replaced. In order to replace the faulty seal, begin by removing the starter housing and taking off the nut that holds the starter wheel to the main shaft. The user will find the old seal on this shaft. Remove it and install the new seal, pushing it into place with the edges of a socket, then tapping it securely into place with a hammer. When choosing a replacement seal, remember to use an OEM genuine replacement part that is guaranteed to match the specs for the original part. This will ensure a quality match and long replacement life. This seal is compatible with Toro, Lawn-Boy, and Briggs & Stratton engines.

This cylinder head gasket is a genuine Midwest Engine replacement part for outdoor appliances with small engines, such as lawn mowers, leaf blowers, vacuums, tillers, and snowblowers. The function of the cylinder head gasket, otherwise known simply as a head gasket, is to separate the cylinder head and the engine block inside an engine. Damage to the cylinder head gasket can occur naturally over time from overuse or general wear and tear. The primary symptom of damage will be the engine exhibiting less power than usual. To test whether it is the cylinder head gasket that is causing engine issues, one can perform a compression test and ascertain whether air is being let out from the head gasket. If that is the case, there might be damage to the cylinder head gasket, making this genuine OEM replacement part essential. Remember to always wear gloves when handling, repairing, and operating outdoor equipment.This cylinder head gasket is compatible with the following brands: Briggs and Stratton, Toro, Cub Cadet, and Simplicity. Part sold individually.

This genuine replacement breather gasket is designed specifically for use with select Briggs & Stratton engines found on lawn and garden equipment. The breather gasket is located in the breather assembly and designed to create an airtight seal. This gasket is subject to compression and high temperatures, which can cause deterioration over time. If the gasket becomes warped, deteriorated, or otherwise damaged, it will affect the seal and the engine performance. Gaskets are often considered a part of routine maintenance and should be inspected regularly for signs of damage. Replace worn gaskets immediately for optimal engine operation. This genuine OEM breather gasket is compatible with Briggs & Stratton and Toro machines that use engines that take this part. There are hundreds of models that use this gasket, including generators, blowers, and other small engines. This is made of composite materials and sold as a single unit. The gasket does not include any additional components or hardware. Always wear gloves and allow the engine to cool before performing any kind of repairs. Be sure to use the appropriate tools and replace gaskets gently to avoid damaging them in the replacement process.

The replacement crankcase gasket seen here is for use with many different types of lawn and garden equipment. The purpose of the crankcase gasket is to fit between the crankcase and the crankcase cover. It helps to make sure that there are no oil leaks that could cause issues with the engine or make a mess when the machine is being stored. Owners should check on the gaskets when they are performing maintenance on their machines. Over time, the gaskets can start to crack or dry out. When this happens, it means that a leak is likely going to occur if it hasn't already. Owners will want to replace these gaskets regularly to ensure they do not have leaks. This is a genuine OEM replacement crankcase gasket that is sold individually. The durable gasket will work for models of many types of machines including lawn mowers, tillers, leaf blowers, generators, wood chippers, log splitters, and certain other small engines. Compatible brands include Briggs & Stratton, Craftsman, Toro, Simplicity, and Cub Cadet.

This crankcase gasket is a replacement part for lawn and garden equipment. It's made to keep the crank from being exposed to the elements and protected from oil and other hazards. This part is located between the crankcase cover and the engine block and is made of a waterproof material that fits the engine block. There are also holes in the component where the crankcase bolts go. If the lawn mower is using a large amount of oil or there is an oil leak noticed, this is an indication that the crankcase gasket needs to be replaced. The original gasket should be peeled off and the new replacement part should be placed against the engine block. Put back on the crankcase cover, tighten the bolts, and ensure the gasket is sealed in place. At this point, oil can be added back to the engine. This is a genuine OEM replacement part that can be used with Briggs & Stratton, Simplicity, Craftsman, Cub Cadet, and Toro lawn mowers, wood chippers, tillers, log splitters, leaf blowers, and generators. Installing the crankcase gasket will require a nut drive, screwdriver, wrench set, and socket set. This original replacement part is sold individually.

This high-quality replacement oil seal prevents oil from leaking where the camshaft exits the crankcase. The camshaft is made of many rotating metal pieces, and while the engine is running, it creates a stupendous amount of thrashing. To keep these parts from rubbing together and overheating, the camshaft needs a good amount of oil. This oil seal helps maintain the right balance of oil in the camshaft. Oil seals can degrade over time after having hot oil repeatedly splashed on them. The most common problem with an oil seal is that it has shrunk or warped and will no longer make a true seal. When this happens, the oil will leak from the engine and the camshaft will begin to overheat. The difficulty of this repair will depend on the lawn appliance that needs repair, but expect to remove the camshaft in order to replace the seal. This part is compatible with engines made by Toro, Lawn Boy, and Briggs & Stratton. It comes sourced from its original manufacturer and ships individually.

The intake gasket on a carburetor serves an important function. It ensures there is no additional air getting into the carburetor. If a gasket on a carburetor is not working properly, it could allow for extra air and dirt to get in, which might cause engine performance issues.Over time, the gaskets will need to be replaced. They can dry, crack, and break over time. It is not a matter of whether they should be replaced, but when. Ideally, gaskets should be replaced whenever the carburetor is serviced. Check on the gaskets occasionally to ensure they are in good condition.This intake gasket is used on a wide range of lawn and garden machines including mowers, tillers, leaf blowers, generators, and wood chippers. This gasket is compatible with select models from Midwest Engine, Briggs & Stratton, Craftsman, Toro, and Simplicity. It is sold individually and is a genuine OEM replacement sourced from the manufacturer.

This air cleaner gasket is made of durable composite material. The main purpose of the gasket is to create an airtight seal for the air cleaner assembly. However, as time goes on, the material can start to wear out and deteriorate and will need to be replaced to ensure the best performance from the outdoor power tool. If the air cleaner gasket is cracked or worn out, replacing it starts with moving the equipment to a stable surface and disconnecting the spark plug wire. Use a screwdriver to remove the top of the air cleaner cover, the filter, and then the bottom half of the cover. Pry out the old air cleaner gasket before installing the new part. Reattach the bottom of the cover, replace the filter, and screw down the top half of the cleaner.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The air cleaner gasket is made for use with lawnmowers, tillers, pressure washers, generators, and wood chippers manufactured by Simplicity, Toro, Craftsman, and Briggs & Stratton.

This replacement gasket set is designed for use with select Briggs & Stratton engines. Gaskets are used in various locations throughout the engines of small outdoor power equipment to provide a seal or flow control to help the engine perform at its best. Over time, gaskets can become worn and degraded, which can lead to leaks and faulty seals. These can affect things like fuel consumption, engine performance, and compression. Replacing gaskets is part of routine maintenance but may also be part of an emergency repair. This gasket set is manufactured to OEM standards and fits a variety of 4 and 5 HP horizontal engines. This gasket set includes 21 pieces that will replace every gasket in the engine on compatible machines. These gaskets are made of durable metal, rubber, and composite materials. No hardware is included with this kit and will require a separate purchase. Be sure to cool the engine and drain the fuel system before replacing gaskets or doing any other internal engine work.

This O-ring seal is used in all sorts of lawn and garden equipment as a seal for the oil dipstick. It helps seal the system from debris and dirt that could otherwise reach the oil and end up in the motor. Over time, an O-ring will start to shrink, which can result in air and oil leaks and a poorly performing engine. If the O-ring has pits, blisters, or pocks on the surface, it will also need to be replaced.If an O-ring seal is worn, damaged, or clogged, it should be cleaned or replaced before the equipment that houses it is used again. A flat head screwdriver can be used to remove the damaged O-ring. Once the old one has been removed, a new one can be placed into the same position before using the tool.This O-ring seal is designed for lawnmowers, snowblowers, tillers, wood chippers, pressure washers, generators, and leaf blowers. It is compatible with equipment from Simplicity, Briggs & Stratton, MTD, Craftsman, Snapper, Toro, Lawn-Boy, and Cub Cadet. The seal is a genuine OEM replacement part directly sourced from the manufacturer. It comes with a single seal.

This replacement exhaust gasket is an authentic OEM part for a snowblower or lawn tractor engine. On these appliances, the exhaust is located quite near to the air filter, meaning that there is a chance that exhaust could leak into the carburetor. The carburetor requires fresh air to oxygenate fuel for combustion, so manufacturers install a gasket to help seal off the exhaust. Once installed, gaskets exist under a lot of pressure and will absorb the heat of the engine. These stresses cause gaskets to slowly degrade and eventually break their seal. If the exhaust gasket blows, the engine will not perform as it should. Be cautious of a noisy engine that burns more fuel than usual and gives off a burning smell. These are signs that the exhaust gasket has given out. If so, use a socket wrench and wrench set to disassemble the blower and air filter housings, then remove the exhaust manifold and change out the broken gasket. This high-quality replacement exhaust gasket is compatible with engines made by Toro, Husqvarna, Briggs & Stratton, and Snapper. It comes sourced from the original manufacturer and ships individually.