Parts for Whirlpool WRT312CZJW00: Liner Parts

The Control is an OEM part for Whirlpool refrigerators. It allows you to adjust temperature settings, control various functions, and monitor the overall performance of your appliance.

A bad refrigerator control can occur due to wear and tear, electrical malfunctions, or accidental damage. If you notice symptoms such as being unresponsive, erratic temperature, or failure to maintain the desired cooling level, it may be time to replace the control.

Symptoms of a bad refrigerator control include:

• Unresponsive control
• Erratic temperature 
• Inability to maintain desired cooling level

Repair your refrigerator's control system by replacing the faulty or worn-out refrigerator control with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement air damper regulates and directs airflow inside the appliance or through its vent path. Replacing a broken or stuck damper helps restore proper air movement and reduces performance issues caused by a jammed or missing flap. What it does:

• Opens and closes to control airflow in the duct or air channel
• Helps maintain proper ventilation or temperature, depending on the appliance design
• Reduces backflow/drafts or uneven airflow
• Common symptoms: poor air movement, rattling/whistling near the vent, drafts, or performance imbalance due to a stuck or broken flap

• 1 air damper

• Disconnect power before servicing; isolate ducting if applicable
• Access the damper location; note orientation of the flap and any seals/gaskets
• Remove the old damper; install the new one with the flap moving freely in the correct direction
• Reassemble and test airflow; seal any duct joints per manufacturer guidance

The User Control and Display Board is an OEM part for Whirlpool refrigerators. As the central processing unit, this board manages and monitors all electronic functions such as temperatures, cycles, alarm settings, and the user interface display.

Causes of failure may include moisture damage, power surges, component fatigue from years of use, or other electrical issues.

Symptoms of a bad board can include:

• Faulty or unresponsive display and control buttons
• Inaccurate temperature readings
• Improper or lack of cooling
• Appliance fails to operate as normal

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire assembly connects the dryer's thermal fuse to the appliance's wiring, ensuring the thermal cut-out can interrupt power when needed for safe operation. Replacing a damaged harness restores reliable electrical connection to the fuse. What it does:

• Carries electrical current to and from the dryer thermal fuse so the fuse can open the circuit when overheated
• Restores proper electrical continuity if wiring is broken, frayed, or burned
• Commonly replaced when the dryer won't heat or stops mid-cycle due to an open thermal fuse circuit
• Helps prevent unsafe wiring conditions caused by damaged insulation or loose terminals

• One wire assembly

• Disconnect power to the appliance before starting any repair
• Inspect connectors and wire routing; replace only if compatible with the original terminals
• Secure harness away from moving parts, sharp edges, and heat sources per OEM routing
• Do not bypass the thermal fuse; the fuse provides a required safety function

This thermistor cover shields and positions the refrigerator's temperature sensor so it reads cabinet air accurately. Replacing a cracked or missing cover helps restore stable temperatures and normal cooling performance.

• Holds the thermistor in place and shields it from direct airflow for accurate temperature sensing
• Helps prevent erratic temperatures, overcooling/undercooling, or long run times caused by an exposed sensor
• Commonly replaced when the original cover is cracked, loose, or missing
• Supports consistent temperature control by ensuring proper sensor placement

• Disconnect power before servicing
• Remove shelves/bins as needed to access the sensor location
• Align the thermistor and seat the cover fully; engage tabs or reuse existing hardware per model
• Avoid pinching the sensor or wiring and verify the cover is snug