Parts for Ge ZTDX1FPSN2SS: Lower Door Parts

This door insulation retainer is a small plastic clip that secures insulation inside a refrigerator/freezer door to help maintain proper temperature and reduce noise. It replaces worn or missing retainers to keep the door liner insulation in place. What it does:

• Secures the door insulation to the inner door liner so insulation stays positioned
• Helps prevent insulation from shifting or sagging that can affect door seal performance
• Commonly used when insulation falls out or the liner shows gaps around the insulation
• Works as a direct-fit replacement for the original retainer designed for the door assembly

• One door insulation retainer clip

• Installation generally requires removing the door panel or liner; keep track of fasteners and trim
• Handle the door liner and insulation carefully to avoid damage or tearing the insulation
• Use proper tools and disconnect power if working near electrical components or lights
• Replace all affected clips for an even, secure fit

This door liner plug snaps into the inner door liner to cover fastener or access holes. It restores a clean, finished look and helps keep grease and debris from entering the door assembly.

• Covers exposed holes in the inner door liner
• Replaces a missing, loose, or damaged plug/cap
• Helps protect the door cavity from splashes and debris
• Restores a neat, factory-finished appearance

• Disconnect power before servicing; for gas ranges, also shut off gas. Allow the appliance to cool completely.
• Open the door and gently pry out the old plug with a plastic trim tool or flat-blade screwdriver.
• Align and press the new plug into the liner until it seats flush.
• Support glass and follow the manufacturer's instructions.

A replacement liner support that secures the refrigerator cabinet liner and keeps interior trim and panels aligned for a proper seal and appearance. Restores stability to cracked or broken support points. What it does:

• Holds the cabinet liner and interior trim in position to prevent gaps and movement
• Helps maintain door seal alignment by keeping liner edges stable
• Reduces rattling or shifting caused by a damaged support
• Commonly replaced when liner pieces are cracked, broken, or loose

• One liner support

• Disconnect power to the appliance before beginning any repair
• Remove food, shelves, and trim pieces as needed to access the damaged support
• This part typically secures with clips or fasteners; inspect existing hardware and replace if necessary

ST10-16 X 7/16"

This is a replacement screw used to secure panels and components on compatible appliances. It provides a direct-fit fastening solution to restore proper part alignment and prevent rattling or loose panels. What it does

• Fastens appliance panels, brackets or assemblies where an 8-18 x 5/8 screw is specified
• Replaces missing or stripped fasteners that allow parts to shift or vibrate
• Restores secure mounting for components to reduce noise and movement
• Useful when a factory screw is damaged, corroded, or lost during service

• One screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver size and type to avoid stripping the head
• Install by hand first, then snug with a driver—do not over-torque
• Keep removed hardware organized to ensure correct reassembly

This set screw secures refrigerator components—most commonly door handles—to their mounting studs. Replacing a missing or stripped screw restores a solid, secure feel and helps prevent loose or wobbly handles.

• Locks the handle to its mounting stud to keep it tight and secure
• Helps resolve a loose, wobbly, sliding, or rattling handle
• Replaces a missing, rounded, or damaged set screw
• Helps maintain proper handle alignment and consistent door operation

• Unplug the appliance or switch off power before servicing
• Ensure the handle is fully seated on the studs before tightening
• Start the screw by hand to avoid cross-threading; then tighten until snug
• Do not overtighten to prevent stripping the screw or handle threads

This 10-32 x 1/4 machine-thread screw secures small appliance components and replacement parts, restoring proper fit and preventing rattles or loose panels. It's a direct-fit fastener used where the appliance needs a short 10-32 machine screw. What it does:

• Fastens panels, brackets, and small assemblies that accept a 10-32 machine screw
• Restores secure mounting when a screw is missing, stripped, or damaged
• Helps stop vibration-related noise from loose parts
• Fits into pre-tapped 10-32 threaded holes

• Unplug or disconnect power before servicing the appliance
• Start threads by hand to avoid cross-threading, then tighten with the proper screwdriver or driver bit
• Do not overtighten; snug until secure to avoid stripping threads or damaging parts
• Keep screws and small parts away from children and pets during installation

This mounting stud secures appliance panels and components in place, restoring proper alignment and stability. It's a simple replacement that helps stop rattling and keeps parts seated correctly for safe operation. What it does:

• Secures panels, brackets, or assemblies to the appliance frame
• Restores proper alignment when a stud is bent, stripped, or missing
• Reduces rattling or vibration caused by loose or damaged fasteners
• Helps maintain safe, stable mounting for controls and internal parts

• Disconnect power to the appliance before servicing.
• Use appropriate hand tools; avoid cross-threading the stud.
• Do not overtighten—tighten until snug to prevent damage.
• If threads are damaged, replace the mating nut or insert as needed.