Parts for Whirlpool WFG770H0FZ2: Manifold Parts

Secures panels, brackets, and trim pieces on ranges and cooktops. Replace if stripped, corroded, or missing to eliminate rattles and looseness.

Gas tubing component for gas ranges. Replaces damaged, cracked, or worn tubing in your range's gas supply system. Essential structural part.

Wire harness for gas ranges. Connects electrical components inside the range. Replace if wires are damaged, frayed, or connectors are broken or melted.

Burner baffle for gas ranges. Sits beneath the burner cap to distribute flame evenly. Replace if cracked, warped, or missing to restore proper appearance.

This manifold assembly routes and supports the appliance's internal fluid/air flow so the unit operates reliably. It replaces a worn or damaged manifold to restore proper routing and help prevent leaks or performance issues. What it does

• Channels internal fluid or airflow to the correct components so systems receive supply as designed.
• Seals connections between inlet and distribution components to prevent leaks.
• Restores proper operation when a cracked, warped, or damaged manifold causes loss of pressure or flow.
• Helps stop intermittent performance problems and related error codes caused by routing failures.

• Disconnect the appliance from power and shut off water or gas supply (as applicable) before beginning work.
• Replace any associated gaskets, O-rings or clamps that show wear to ensure a proper seal.
• Inspect mounting points and mating surfaces for damage; tighten fasteners to OEM torque if specified.

If your gas range burner won't light or flame won't adjust properly, replace the burner valve. This part controls gas flow for ignition and heat control.

Fix a burner that won't light or has weak flames with this gas range burner valve. Controls gas flow to restore proper ignition and flame strength.

Replace a faulty gas saddle valve if your range burner won't ignite or produces weak flames. Controls gas flow to restore proper burner operation.

Oven not browning or crisping food properly? This broil burner assembly restores focused high heat for perfect broiling. Direct-fit installation.

Oven won't heat or bakes unevenly? A corroded or clogged bake burner disrupts flame distribution. This gas burner restores consistent oven performance.

Controls gas flow and pressure to burners and oven in gas ranges. Replace if leaking, cracked, or damaged to restore safe gas distribution.

Fix an oven that won't light or hold temperature with this gas range igniter. Common repair for clicking sounds without ignition. DIY-friendly, 10-20 min.

If your gas range burner won't light or has weak flames, the flexible gas tubing may be damaged or disconnected. This line restores safe gas flow.

Leaking water connection under your range? This fitting secures the water line to internal plumbing, stopping leaks from cracked or loose connectors.

Fix a broil burner that won't light or clicks repeatedly. This spark electrode generates the ignition spark needed for reliable broil operation.

Fix weak or uneven burner flames with a new gas range burner orifice. This fitting meters fuel flow for consistent heat. Easy 15-minute repair.

Fix weak or uneven flames with this gas range burner orifice. Controls gas flow for consistent heat and reliable ignition. Easy DIY repair.

Weak or uneven flame on your gas range? A worn or clogged burner orifice disrupts gas flow. Replace it to restore proper flame size and safer cooking.

Fix weak or uneven flames on your gas range with this burner orifice. Controls gas flow to restore steady heat. Simple DIY install in minutes.

Replacement mounting screw for securing range panels, brackets, and internal components. Replace missing, stripped, or rusted screws to restore fit.

Replacement mounting screw for securing panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.

Self-tapping screw secures panels, brackets, and trim to range frames and housings. Replace worn, missing, or stripped fasteners to restore fit.

Range won't ignite or has delayed ignition? This ignitor retaining clip secures your ignitor to the burner assembly for reliable starts. Simple fix.

LP orifice kit for gas range bake and broil burners. Includes conversion orifices to switch from natural gas to liquid propane. Replace when missing.