Parts for Ge AZ61H07EABM2: Motor & Chassis Parts

This rubber cover is a small protective trim piece that cushions and seals appliance openings and hardware to reduce wear and block dirt or moisture. It restores a finished appearance and helps prevent rubbing or vibration damage. What it does:

• Covers and cushions exposed edges or hardware to reduce wear and rattling
• Helps keep dirt, lint and moisture out of small gaps and openings
• Restores a clean, finished look to the area where it installs
• Useful when the original cover is cracked, torn or missing

• Disconnect power at the breaker before accessing internal areas on electrical appliances
• Typically installs by snapping into place or sliding over the mating flange; do not force into position
• Inspect the mating surfaces for debris or damage and clean before installing
• If fasteners are present, tighten securely but avoid over-torquing to prevent tearing

A condenser plate that secures and shields the refrigerator condenser assembly for stable operation and proper airflow. Replaces a damaged or missing plate to help maintain condenser protection and consistent cooling performance. What it does:

• Secures the condenser assembly and related components to the cabinet/frame
• Protects the condenser coil from debris and physical damage
• Helps direct airflow around the condenser for efficient heat dissipation
• A failing or missing plate can allow vibration, rattling, or reduced cooling effectiveness

• One condenser plate

• Disconnect power to the appliance before starting any repairs
• Use care handling the plate—edges may be sharp
• Retain and reuse existing mounting hardware if compatible; verify hole alignment before tightening

This bearing assembly supports the dryer drum and helps the drum rotate smoothly for quiet, even drying. Replacing a worn bearing restores stable drum movement and reduces noise and vibration. What it does:

• Provides a low-friction support surface for the dryer drum, helping it spin properly
• Prevents drum wobble and off-center rotation that can wear belts and rollers
• Reduces squealing, grinding, or rumbling noises caused by a failing bearing
• Helps maintain even drying by keeping the drum aligned

• Disconnect power and fuel (gas) supply before starting any repair
• Access typically requires removing the dryer front or rear panel and drum; refer to a model-specific repair guide
• Use proper tools and support the drum during removal to avoid damage
• Inspect adjacent parts (shaft, seal, rollers) for wear and replace if visibly damaged

This bearing holder secures the dryer drum's rear bearing, stabilizing rotation to reduce wobble and noise for smooth operation. It replaces a worn or damaged support to restore drum alignment and quiet performance. What it does:

• Positions and holds the rear drum bearing so the drum spins evenly
• Prevents excessive drum wobble and uneven wear on bearings
• Helps reduce grinding, squeaking, or rumbling caused by a failing support
• Restores proper drum alignment for reliable tumbling and airflow

• Disconnect power (and gas if applicable) before starting any repairs
• Replacing may require removing the dryer drum and accessing the rear bulkhead
• Inspect the bearing, seal, and adjacent components; replace if damaged
• Use proper tools and follow the appliance service manual

This DC In Motor Angle is the motor mounting bracket that secures and aligns the DC drive motor for proper operation. It helps keep the motor stable so the appliance runs quietly and reliably. What it does:

• Holds the DC motor in the correct position to maintain alignment with the drivetrain
• Reduces movement and vibration that can cause noise or premature wear
• Keeps motor mounting points stable to prevent intermittent motor contact or rubbing
• Supports consistent motor engagement for reliable performance during operation

• Disconnect power before beginning any repair to avoid electric shock.
• Basic hand tools required; follow the appliance service manual for correct removal and reinstallation order.
• Inspect surrounding fasteners and motor mounts; replace any damaged hardware for a secure fit.

This Closs fan is a direct-replacement fan assembly designed to restore proper air circulation in the appliance and help maintain even cooling and consistent performance. It replaces a worn or damaged fan without needing a full module swap. What it does:

• Circulates air inside the compartment to support consistent temperature and efficient operation
• Replaces a damaged, cracked, or missing fan that causes reduced airflow
• Stops or reduces abnormal noise caused by a failing or unbalanced fan
• Helps prevent localized warm spots that can lead to food spoilage or performance loss

• One Closs fan assembly

• Disconnect power to the appliance before beginning any repair
• Handle fan blades carefully to avoid damage; verify correct orientation before fastening
• Basic hand tools are typically required