Mtd Gold Snow Removal Equipment Parts

This 4-way chute cable is a genuine MTD part, sold individually. This 4-way chute cable can be used as a replacement part in a snowblower. The purpose of the 4-way chute cable in a snowblower is to facilitate the dispersion and dispensing of snow during use by allowing the operator to control the pace and directionality of the snow.This 4-way chute cable in a snowblower might have to be ordered as a complete replacement in a 4-way chute cable that is not working or has been exhibiting signs of damage during the typical lifespan of the appliance.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This 4-way chute cable is compatible with the following outdoor appliance brands: MTD and Cub Cadet.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

The flywheel key keeps the engine flywheel and the crankshaft connected. In the event that the engine is forced to a sudden stop, the flywheel key could be sheared off, making it impossible for the engine to start back up again. Replacing the flywheel key is a part of routine maintenance for many modern engines, so it should be inspected and replaced as needed. This sturdy metal flywheel key is easy to install, but remember to choose the right torque setting when doing the replacement. Always disengage the spark plug and wear gloves when replacing engine parts. This genuine flywheel key is designed to be used in a number of lawn and garden equipment products from MTD, Troy-Bilt, Yard Machines, Cub Cadet, Yard-Man, Husky, and Bolens. It can be used as a replacement for many models of snowblowers, lawnmowers, and log splitters. Sold individually.

This replacement part is a stud assembly. This is a genuine replacement part made by MTD. This stud assembly is responsible for keeping the muffler in place and secure so that the lawn mower may operate smoothly and according to the user's preferences. A new stud assembly might be needed if the current one is misplaced or damaged. It is not unusual for the studs to become stripped over time and need to be replaced. If the muffler is no longer able to stay in place, it can be due to the studs and should be looked into. Be sure the engine is completely turned off before attempting to replace this part. This stud assembly is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This is a gasket kit that contains a variety of parts utilized in many kinds of lawn and garden equipment. Each of the parts in the kit is created to seal two surfaces inside the equipment. The components in the kit include a carburetor insulator plate, a carburetor gasket, a carburetor insulator gasket, two carburetor gasket plates, an exhaust pipe gasket, a valve cover gasket, and an oil drain plug washer. If a lawn and garden tool is leaking fuel, air, or oil, these parts can be used to replace the faulty component.A socket wrench or small monkey wrench and a screwdriver will be needed to replace any parts included with the gasket kit. Make sure the lawn equipment is on a flat surface and the spark plug wire has been disconnected. Disassemble any needed components to reach the gasket or other part that needs to be replaced. Put in the new component and reassemble before use.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual kit. The external gasket kit is designed to be used with snowblowers manufactured by Yard-Man, Huskee, MTD, Yard Machines, Troy-Bilt, Cub Cadet, and Craftsman.

This throttle linkage spring is typically attached to the throttle cable, although it may be attached to the carburetor or the throttle body on select models. This spring will close the throttle valve, which helps reduce the fuel flow to the engine and helps to slow it down. The spring can become stretched or snap over time with regular use. A faulty throttle spring could be identified by the throttle sticking or lacking any control at all. This simple repair will require needle nose pliers, sockets, a screwdriver, and a wrench. Be sure to use gloves to perform all repairs and use caution when replacing the throttle spring to prevent damage to the new part. This OEM throttle spring is designed for use with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and other small engines in lawn care equipment. It is compatible with more than 150 models and a number of brands, including Troy-Bilt, Husky, Yard-Man, MTD, Yard Machines, and Cub Cadet.

This replacement part is a gasket kit. It is a genuine replacement part made by MTD. This gasket kit is an essential part of the appliance and allows the engine to run properly and smoothly during use.A new gasket kit might be needed if the user hears unusual noises coming from inside the machine. If the machine is having trouble being turned on or cannot turn off, it might be a faulty gasket. If the appliance is slow to start this can also indicate a faulty kit. Be sure the engine is turned completely off and cooled down before attempting this repair. Be sure to refer to the owner's manual before replacing this gasket kit.This part is sold as a single kit. This gasket kit is a genuine OEM replacement part and is sourced directly from the manufacturer.