Parts for Kenmore 795.51839413 (79551839413, 795 51839413): Other Parts

The Water Filter LT800P is an OEM part for LG refrigerators. This filter is designed to remove contaminants from the water supply, ensuring clean and fresh-tasting water and ice.

Causes of a bad water filter can include extended use beyond its recommended lifespan, exposure to high levels of contaminants, or damage to the filter itself.

Symptoms of a bad Water Filter LT800P include:

• Unpleasant taste or odor in the water or ice
• Reduced water flow from the dispenser
• Indicator light signaling the need for replacement
• Visible sediment or particles in the water

This OEM LG part is also compatible with Sears/Kenmore.

This is a replacement drain tube assembly that directs water from the appliance tub to the drain pump or household drain, helping restore proper water removal and reduce leaks. It's a direct-fit service part used in the drainage system. What it does:

• Channels wastewater away from the tub to the drain pump or drain line
• Helps prevent pooling or slow draining caused by a damaged or disconnected tube
• Restores a sealed path to reduce leaks at the tub-to-pump connection
• Suitable when the original drain tube is cracked, split, collapsed, or leaking

• One drain tube assembly as shown

• Disconnect power and water before beginning any repair to avoid shock or flooding
• Inspect and clean mating surfaces and clamps; replace clamps if corroded or damaged
• Ensure correct routing and secure connections to prevent kinks and leaks

This replacement lever spring restores tension to a lever-style mechanism so the lever returns and operates reliably. Use it when a worn spring causes the lever to stick, slip, or fail to engage properly. What it does

• Replaces the worn or weakened spring in a lever assembly to restore proper return tension
• Helps prevent the lever from sticking, slipping, or failing to stay engaged
• Restores consistent mechanical movement for reliable operation
• Reduces intermittent or flaky lever behavior caused by a damaged spring

• Disconnect power to the appliance before starting any repair
• Inspect the lever assembly and mounting points; replace only the spring explicitly listed
• Use appropriate hand tools and pliers; avoid overstretching the spring during installation

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

This insulated duct assembly cushions and channels airflow while reducing noise and heat transfer. It restores proper ventilation and helps maintain efficient operation and quieter performance. What it does:

• Replaces a damaged or worn insulated duct to restore correct airflow routing
• Reduces vibration noise and minimizes heat loss from the airflow path
• Helps prevent air leaks that can cause reduced performance or localized heating
• Fits where the original insulated duct was installed and works with the appliance's venting system

• Disconnect power and any gas supply before servicing
• Inspect surrounding seals and fasteners; replace any damaged clips or tape
• Follow OEM instructions for routing and securing the duct to avoid pinching

This case assembly for the refrigerator control area houses and protects the control board and user interface components, helping keep electronics secure and accessible for diagnostics or replacement. What it does:

• Protects the control board and wiring from damage, dust, and moisture
• Provides mounting points and alignment for the user interface and controls
• Keeps the control area organized for service access and replacement
• Helps maintain proper airflow around control electronics where applicable

• Power off and unplug the appliance before servicing to avoid shock or injury
• Handle the control housing and any attached ribbons or connectors carefully to avoid damage
• Keep screws and small fasteners organized; verify fit before final assembly
• Follow manufacturer instructions and ESD precautions

This bucket cover restores the top enclosure of the washer tub so water stays contained and the wash basket operates as designed. It helps protect laundry and internal components from splashes and debris. What it does:

• Fits over the wash bucket to cover the tub opening and direct water flow
• Helps prevent water spray and leaks during fill and spin cycles
• Keeps clothing and loose items from entering the tub gap
• Contributes to stable basket operation and reduces direct contact with internal parts

• Disconnect power and water supply before beginning any repair
• Remove the cabinet or access panel as required by your model to reach the bucket area
• Use appropriate hand tools; support the tub/basket to avoid displacement during removal/installation
• Follow OEM instructions for torque, alignment, and reassembly

This shelf assembly replaces a damaged or missing refrigerator shelf to restore stable storage and organization. It provides a durable, easy-to-install surface for holding food, containers, and other items in the fresh-food compartment. What it does

• Provides a flat, stable surface for storing food and containers inside the refrigerator
• Replaces cracked, chipped, or warped shelves that cause items to tip or slide
• Restores proper spacing and organization to improve usable storage area
• Compatible with factory shelf supports and slides to sit securely in place

• One refrigerator shelf assembly (exact configuration as shown)

• Remove all food and loose items before installing; handle glass edges carefully
• Slide the shelf into existing tracks or rest on supports until it sits level and secure
• If shelf uses clips or brackets, confirm alignment before applying pressure
• If damaged supports or clips are present, replace those parts to ensure a safe fit

A replacement freezer shelf assembly that restores storage support and organization inside the freezer compartment. Replaces a cracked, warped or missing shelf so frozen items sit level and are easier to access. What it does:

• Provides a sturdy surface to hold frozen foods and containers
• Replaces shelves that are cracked, bent, or no longer supporting weight
• Helps restore proper airflow and organization inside the freezer compartment
• Useful when shelf clips or mounting points are damaged or worn

What's included: One freezer shelf assembly Install notes:

• Unplug the appliance or shut off power before starting work
• Remove contents from the shelf and surrounding area to avoid breakage
• Handle with care if the shelf includes glass; wear gloves and eye protection
• Basic tools may be needed to release or secure mounting clips

This Tray Cover Assembly replaces a cracked or damaged plastic cover that protects and secures the appliance tray, restoring proper fit and appearance. It provides a simple, direct replacement for worn or broken covers. What it does:

• Covers and protects tray contents from debris and spills
• Keeps the tray seated and aligned to prevent rattling or shifting
• Replaces cracked, warped, or broken covers that no longer stay in place
• Helps restore proper function and appearance after impact or wear

• One tray cover assembly

• Disconnect power or unplug the appliance before starting any repair
• Remove the old cover by releasing retaining clips or screws as applicable; handle plastic parts gently to avoid breakage
• Align the replacement cover and snap or fasten it into place until all clips engage

This small stopper fits inside the handle assembly to limit travel and keep the handle properly seated. Replacing a worn or missing stopper restores a solid, secure feel when opening and closing your appliance.

• Provides a positive stop for handle movement
• Helps keep the handle aligned and seated against its mounts
• Replaces a cracked, deformed, or missing stopper
• Common signs: handle feels loose or wobbly, over-rotates, or shifts/clicks during use

• Unplug the appliance before servicing to prevent injury
• Support the handle and protect the finish while removing fasteners
• Note the original stopper's orientation and install the new one the same way
• Tighten fasteners evenly; do not overtighten to avoid damaging plastic or finishes

This is the door handle mounting bracket assembly that secures the handle firmly to the door. It replaces a damaged or stripped bracket to restore a solid, wobble-free grip and reliable handle attachment.

• Mounts and secures the door handle to the door/frame
• Maintains alignment to prevent handle wobble or looseness
• Replaces cracked, broken, or stripped brackets to restore proper attachment
• Typical symptoms: loose or wobbly handle, handle pulls off, visible damage at the handle mount, rattling at the handle area

• Disconnect power before servicing and work carefully to avoid damaging the door surface
• Support the handle while loosening and tightening set screws or fasteners
• Retain and reuse original mounting hardware if it's in good condition
• Align the new bracket in the original location; do not overtighten fasteners

This door basket is the upper-rack basket assembly that holds small items securely in the dishwasher, helping keep utensils and small dishes positioned for thorough cleaning. It replaces a damaged or worn basket to restore proper loading. What it does:

• Secures small items and utensils in the upper rack so they stay in place during wash cycles
• Prevents items from falling into the lower rack or blocking spray arms, which can reduce cleaning performance
• Replaces cracked, warped, or broken basket sections that no longer support dishes safely
• Helps maintain proper water flow and coverage by keeping load items organized

• One door basket (upper rack)

• Designed to snap or slide into the upper rack;
• Inspect surrounding rack components and track for wear before installing
• Disconnect power and follow basic dishwasher safety procedures if service access requires removing panels
• Use common hand tools;

This Door Basket is the removable shelf that locks into the refrigerator door to hold bottles, jars, and condiments. Replacing a cracked or missing bin restores secure storage and helps keep items from tipping when the door moves.

• Provides on-door storage for bottles, jars, condiments, and small items
• Replaces a broken, cracked, or missing door bin
• Attaches to the door liner to keep items contained during opening/closing
• Common signs it's needed: bin won't stay seated, plastic is damaged, or items fall from the door

• Remove any items and support the bin with both hands
• Lift the old bin up and out of the door liner channels; align the new bin and press down until fully seated
• Ensure both ends are locked in evenly before reloading
• Handle plastic carefully to avoid cracking; do not force into place

This refrigerator door bin replaces a broken or missing shelf on the inner door, restoring organized, easy-to-reach storage. It seats into the molded tabs on the door liner to hold items securely and maximize usable space.

• Holds bottles, jars, and condiments on the door to free up shelf space
• Replaces cracked plastic or broken locking tabs
• Addresses a bin that won't stay seated, sags, or wobbles
• Ideal when a bin is missing or too damaged to safely store items

• Remove the old bin by lifting up to release it from the retaining tabs, then pull out
• Align the new bin's tabs/hooks with the slots on the door liner
• Press down/slide into place until fully seated and level
• Verify the bin is secure before loading; distribute weight evenly to prevent damage

The Hinge Assembly, Upper is an OEM replacement part for LG refrigerators. This upper hinge assembly works together with the center hinge to provide balanced support and motion to the refrigerator doors.  

Causes of a bad upper hinge assembly can include long-term wear and tear, accidents, or overloading the doors with excessive weight. Over time, the hinges may become misaligned or components can weaken.

Symptoms of a bad upper hinge assembly include:

• Gaps appearing along the top edge of the door seal
• Doors no longer closing flush or sealing properly  
• Difficulty opening and closing the doors
• Noises or creaking coming from the hinge area

This OEM LG part is also compatible with select Sears/Kenmore brand models. 

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

This cap assembly for the duct secures and seals a dryer/exhaust duct connection to restore proper airflow and help prevent leaks. Designed to replace a worn or damaged duct cap and keep the vent path intact. What it does:

• Caps and secures the duct outlet to maintain a tight connection and reduce air leakage
• Helps direct exhaust airflow through the duct instead of escaping at the connection
• Can reduce lint and moisture escaping at a faulty or damaged duct joint
• Commonly replaced when the original cap is cracked, broken, or no longer holds the duct in place

• One cap assembly

• Disconnect and power off the appliance before servicing; follow the manufacturer's service manual
• Basic hand tools typically required; check panel or vent access before starting
• Inspect surrounding duct and fasteners; replace damaged clamps or tape as needed

NOTE: This part also requires software update kit CJT30000002. DO NOT INSTALL WITHOUT UPDATING SOFTWARE. Call for more information.

The Compressor Overload is an OEM part for LG refrigerators. It works to prevent damage by automatically shutting off power to the compressor in the event of overheating, helping to extend the life of the compressor.

Causes of a bad compressor overload include normal wear and tear over time, extended use in high-heat conditions, or physical damage that impacts its protective functions.

Symptoms of a bad overload include:

• The compressor failing to start or run
• Strange noises coming from the compressor
• An increase in the refrigerator's operating temperature
• Frequent and unexpected shut-offs of the compressor

This OEM LG part is also compatible with Sears/Kenmore refrigerator models.

This damper cushions and isolates the refrigerator compressor to reduce vibration and noise for smoother operation. It helps maintain stable compressor mounting and prevents metal-to-metal contact that can cause wear or rattling. What it does:

• Absorbs compressor vibrations to reduce noise and movement
• Helps protect the compressor housing and mounting points from shock
• Can reduce rattling or knocking sounds originating near the compressor area
• Supports proper alignment of the compressor assembly during operation

• One compressor damper (mounting isolator)

• Turn off power at the breaker and unplug the appliance before servicing
• Inspect mounting area and hardware; replace any damaged fasteners before installing the damper
• Position the damper on the compressor mount as shown in the service manual and secure per OEM guidance

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

The Drier Assembly is an OEM part for LG refrigerators. This part is responsible for removing moisture and contaminants from the refrigerant. This ensures that the refrigerant circulates effectively and efficiently, preventing damage to other components and maintaining the refrigerator's cooling performance.

Causes of a bad Drier Assembly can include contamination from moisture entering the refrigerant lines, blockages from debris or particulates, and general wear and tear over time that reduces its effectiveness.

Symptoms of a bad Drier Assembly include:

• Reduced cooling efficiency or warm refrigerator temperatures
• Unusual noises from the refrigeration system
• The compressor running continuously or cycling frequently
• Frost buildup on the evaporator coils due to improper refrigerant flow

This OEM LG part is also compatible with Sears/Kenmore models.

This fan guide is the molded support bracket that positions and protects the refrigerator/freezer evaporator or condenser fan blade, helping maintain proper airflow and reduce noise from the fan assembly. Designed to fit into the fan housing area. What it does:

• Holds the fan blade and motor assembly securely in the correct position for consistent airflow
• Directs airflow across the evaporator or condenser for efficient cooling performance
• Helps prevent fan blade contact with other components, reducing rubbing noise and wear
• Keeps debris away from the fan to protect the motor and prolong fan life

• One fan guide/support bracket

• Disconnect power to the appliance before inspecting or replacing the part
• Access may require removing interior panels or the rear access panel depending on model
• Verify correct orientation and secure mounting; do not force the part into place
• Test fan operation after reassembly to confirm proper fit and clearance

This condenser assembly is the factory-style replacement condenser wiring and support used in compatible LG refrigerators to restore proper condenser connections and securement. It helps maintain reliable cooling system electrical routing and component support. What it does:

• Provides the correct wire routing and connections for the refrigerator condenser area
• Secures condenser components in place to prevent vibration and wear
• Restores proper electrical paths for condenser-related circuits to help the compressor/fan operate as intended
• Helps address symptoms like intermittent cooling, unusual vibration, or loose wiring in the condenser compartment

• One condenser assembly as shown

• Disconnect power and follow manufacturer safety procedures before starting work
• Inspect surrounding components (fan, compressor mounts, tubing) while replacing this assembly

This fan assembly is the rotating blower that moves air through the appliance to support drying, venting, and internal cooling. Replacing a worn fan restores proper airflow and reduces noise or overheating risks. What it does

• Spins the blower wheel to circulate air for drying, venting, or cooling functions.
• Restores airflow when the appliance has weak or no air movement.
• Reduces abnormal rattling, grinding, or humming caused by a damaged motor or wheel.
• Helps prevent overheating by maintaining adequate internal ventilation.

• One fan assembly.

• Disconnect power before starting any repair.
• Access may require removing outer panels or interior trim; keep fasteners organized.
• Handle wiring connectors and harnesses carefully; match connector positions during reassembly.
• Test operation after installation and reassemble panels securely before returning the appliance to service.

The Dispenser Micro Switch is an OEM part for LG refrigerators. It is a component of the ice and water dispensing system, responsible for activating the dispenser when the lever is pressed. 

Causes of a bad Dispenser Micro Switch can include mechanical wear from frequent use, failure due to moisture or debris affecting the switch’s contacts, or electrical faults that prevent proper signaling.

Symptoms of a bad Dispenser Micro Switch include:

• The dispenser not releasing ice or water when the lever is pressed.
• Continuous dispensing or dripping after the lever is released.
• Intermittent or no response from the dispenser controls.

This OEM LG part is also compatible with Sears/Kenmore.

This DC drive motor powers the washer drum, restoring agitation and spin so loads clean and drain properly. It replaces a failed drive motor to help appliances resume normal wash and spin cycles. What it does:

• Turns the drum for agitation and high-speed spin to remove water from clothes
• Replaces motors that hum, do not spin, or have irregular rotation
• Can stop or reduce vibration and noise caused by a failing motor
• Helps resolve wash cycles that stall or fail to advance due to motor faults

• Disconnect power and water before starting any repair
• Remove outer panels and drum access components as required for your model
• Handle the motor and rotor carefully; support the assembly to avoid damage
• Verify electrical connections and mount alignment before restoring power; test with no load

This DC motor drives the rotating component it's attached to—such as a fan blade, impeller, or gear—restoring smooth, reliable motion so your appliance can maintain the airflow or mechanical movement it was designed to deliver.

• Converts electrical power into controlled rotation for the connected part
• Restores proper airflow or mechanical movement when a motor has failed
• Common symptoms include the connected part not running, intermittent operation, unusual noise, or error codes
• Replaces a seized, noisy, or burnt-smelling motor

• Disconnect power (and water, if applicable) before servicing
• Note wire/harness orientation and routing before removal
• Transfer any reusable brackets, grommets, or the driven component (fan blade/impeller) from the original as needed
• Ensure the shaft spins freely and check for smooth, quiet operation after reassembly

This motor bracket secures the washer motor to the chassis, restoring proper alignment and reducing vibration and noise caused by a loose or damaged mount. Fits the OEM motor location to keep drive components stable. What it does:

• Provides a stable mounting point for the motor to prevent movement and misalignment
• Helps reduce excessive vibration and rattling during spin and agitate cycles
• Prevents motor-to-chassis contact that can cause grinding or unusual noises
• Maintains correct motor position for proper belt/drive engagement

• Disconnect power and water before starting any repair
• Support the motor or drum when removing/installing the bracket to avoid strain on wiring or drive components
• Keep existing hardware if reusable; replace stripped or damaged screws/bolts with OEM-specified fasteners
• If noise or vibration persists after installation, inspect motor bearings, suspensions, and mounts for related wear

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Front Evaporator Motor Grommet is an OEM part for LG refrigerators. This grommet cushions and secures the evaporator motor, reducing vibrations and noise during operation to ensure efficient cooling.

Causes of a bad grommet can include prolonged use leading to material fatigue, exposure to extreme temperatures, or physical damage from accidental impacts. A damaged grommet can result in increased noise and potential misalignment of the evaporator motor.

Symptoms of a bad evaporator motor grommet include:

• Increased noise from the refrigerator
• Vibrations or rattling sounds
• Poor cooling performance
• The evaporator motor becoming loose

This OEM LG part is also compatible with Sears/Kenmore.

The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer. 

Symptoms of a bad Ice Dispenser Door Motor include:

• The dispenser door not opening or closing properly,
• Ice not being dispensed when activated,
• Unusual noises coming from the dispenser mechanism.

Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.

This OEM LG part is also compatible with Sears/Kenmore.

The Capacitor is an OEM part for LG refrigerators. It plays a vital role in the electrical system, providing the necessary power boost to start the compressor and maintain its operation. This component ensures that the refrigerator runs efficiently by stabilizing voltage and improving overall performance.

Common causes of a bad capacitor include electrical surges, wear and tear over time, or exposure to excessive heat.

Symptoms of a bad capacitor include:

• The refrigerator not cooling properly
• The compressor not starting or running intermittently
• Unusual noises coming from the refrigerator
• The refrigerator cycling on and off frequently

This OEM LG part is also compatible with Sears/Kenmore models.

This main control board is the refrigerator's primary power and logic board, regulating major functions and enabling normal operation. Replacing a faulty board restores control of electronic features and power distribution. What it does:

• Receives and routes incoming power to the appliance's subsystems so controls and motors can run.
• Interprets user inputs and sensor signals to manage cooling cycles, defrost, and other electronic functions.
• Commonly linked to symptoms such as no power to controls, unresponsive display/buttons, or intermittent operation.
• May stop appliance functions if damaged by power surges, moisture, or component failure.

• Disconnect power to the appliance before starting work to avoid shock or damage.
• Handle the board by the edges and avoid touching components; observe anti-static precautions.
• Verify connector orientation and secure all wiring harnesses before restoring power.

The Ice Dispenser Auger Motor is an OEM part for LG refrigerators. This part is designed to drive the auger that moves ice from the ice bin into the dispenser chute. This motor ensures that ice is available on demand through the door dispenser. 

Causes of a bad Ice Dispenser Auger Motor can include electrical issues such as a burnt-out motor, wear and tear on the motor's components over time, or damage from moisture or ice buildup that can affect the motor's functionality. 

Symptoms of a bad Ice Dispenser Auger Motor include:

• The ice dispenser not dispensing ice, even though the ice bin is full.
• A humming or buzzing sound from the motor area without any ice being dispensed, indicating the motor is receiving power but failing to turn the auger.
• Intermittent or inconsistent dispensing of ice, which can suggest a failing motor.

This OEM LG part is also compatible with Sears/Kenmore.

This water filter assembly secures the refrigerator's replaceable water filter and routes water to the dispenser and ice maker. Replacing a cracked or leaking assembly restores proper flow and helps ensure a tight, reliable seal at the filter connection. What it does:

• Holds and seals the replaceable water filter cartridge
• Channels inlet water through the filter to the dispenser and ice maker
• Helps prevent leaks at the filter connection and housing
• Common symptoms: leaks around the filter area, low or no water to dispenser/ice maker, filter won't seat or stay in place, visible cracks on the housing

• 1 water filter assembly

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure by dispensing water; place a towel to catch residual water
• Transfer fittings/lines carefully and seat connections fully; do not overtighten
• Restore water, check for leaks, and run water to purge air from the system

The Water Filter LT800P is an OEM part for LG refrigerators. This filter is designed to remove contaminants from the water supply, ensuring clean and fresh-tasting water and ice.

Causes of a bad water filter can include extended use beyond its recommended lifespan, exposure to high levels of contaminants, or damage to the filter itself.

Symptoms of a bad Water Filter LT800P include:

• Unpleasant taste or odor in the water or ice
• Reduced water flow from the dispenser
• Indicator light signaling the need for replacement
• Visible sediment or particles in the water

This OEM LG part is also compatible with Sears/Kenmore.

The Dispenser Motor is an OEM part for LG refrigerators. It is the motor component housed inside the external ice and water dispenser.  

This dispenser motor controls dispensing functions by operating the ice and water delivery system. It works with electronic controls to precisely dispense desired amounts of cubed ice or chilled water on demand.

Causes of a bad dispenser motor can include failures in motor electronics, damage from water damage, or normal wear over time.

Symptoms of a bad dispenser motor include:

• Inability to dispense ice or water through the external spout  
• Malfunctions in ice or water delivery amounts
• Abnormal sounds or jerky motions from the dispenser area

Replacing the dispenser motor with this genuine LG OEM part restores convenient dispensing capabilities. It is also compatible with Sears/Kenmore refrigerator models.

The Water Tank is an OEM part for LG refrigerators. This tank stores and supplies water to the refrigerator's ice maker and water dispenser, ensuring a consistent supply of fresh, filtered water. It is designed to fit securely within the refrigerator, maintaining hygiene and preventing leaks.

Over time, the water tank can become worn out, cracked, or contaminated. Common causes of a bad water tank include regular wear and tear, exposure to extreme temperatures, or damage from mishandling or improper installation.

Symptoms of a bad water tank include:

• Leaking water inside the refrigerator
• Low water flow to the dispenser or ice maker
• Unusual tastes or odors in the water
• Visible cracks or damage to the tank

This OEM LG part is also compatible with Sears/Kenmore.

This water valve assembly controls the flow of water into the appliance, restoring reliable fill and stopping unwanted leaks or no-fill conditions. It's a direct-replacement component designed for easy swap-in repairs. What it does:

• Opens and closes to allow water into the appliance when a cycle or dispenser calls for it
• Restores normal water fill for ice makers, dispensers, or wash cycles
• Stops unwanted or continuous filling caused by a failed valve
• Helps eliminate leaks or dripping when the valve seal is compromised

• Disconnect power and shut off the water supply before beginning work
• Handle electrical connectors and solenoid terminals carefully; replace any damaged wiring or connectors
• After installation, restore power and water, then run a test cycle and check all connections for leaks

This LED assembly restores the TV's backlight by replacing a failed LED strip, improving screen brightness and uniformity for visible picture. Designed to match the original part's fit and function. What it does:

• Replaces the TV's failed LED backlight strip to restore screen illumination
• Can resolve symptoms such as dim or dark screen, uneven brightness, or vertical/horizontal dark bands
• Helps stop flickering or intermittent backlight outages when caused by the LED strip
• Works with the TV's existing power board and connectors

• Disconnect power and unplug the TV before starting any repair
• Handle LEDs and the circuit board carefully; avoid touching LED surfaces and flexing the strip
• Use anti-static precautions and keep small screws and brackets organized during reassembly

This LED assembly is the backlight strip used to illuminate an LCD panel, restoring even screen brightness and color when individual LEDs fail or the backlight dims. It replaces a damaged or faulty LED strip to improve picture visibility. What it does:

• Provides uniform backlighting behind the LCD panel for consistent brightness across the screen
• Replaces burned-out or flickering LEDs that can cause dark spots, vertical bands, or uneven lighting
• Stops intermittent or flashing backlight-related display issues caused by failed LED elements
• Works with the TV's existing power module and driver board to restore normal backlight operation

• Disconnect power and unplug the TV before beginning any repair
• Handle the LED assembly and circuit board by the edges; avoid touching LEDs or solder joints
• Use proper tools and keep small screws/parts organized; follow TV disassembly guidance for your model

This temperature sensor monitors refrigerator temperatures and sends signals to the control board so it can regulate cooling and airflow. Replacing a failed sensor restores accurate readings and consistent temperatures in the fresh food and freezer sections.

• Measures internal compartment temperature for the control system
• Helps the board regulate compressor and evaporator fan operation to maintain setpoints
• Supports stable cooling and proper system cycling
• Failure may present as sections too warm or too cold, temperature swings, or frequent cycling

• Disconnect power to the refrigerator before servicing
• Access point varies by model; commonly behind an interior cover or clipped near the evaporator
• Note wire routing and any clips/insulation and transfer them to the new sensor
• Restore power and allow up to 24 hours for temperatures to stabilize