Parts for Frigidaire CGMV173KBB: 03 - Oven,Cabinet Parts

Microwave not heating but humming loudly? A failed high-voltage diode is often the cause. This rectifier converts AC to DC for the magnetron circuit.

Microwave not heating? A failed high voltage capacitor often causes weak or no heating. This repair requires electrical expertise and safety precautions.

Microwave turntable stopped spinning? This motor restores rotation to your carousel platter. Simple DIY repair—three screws and one plug. 5-10 minutes.

Fixes microwave that won't power on or shuts off unexpectedly. This thermal cutout switch prevents overheating by cutting power when temps get too high.

Microwave not heating but runs normally? A failed magnetron is the likely cause. This repair restores heating function. Moderate DIY difficulty.

Microwave runs but won't heat, or stays on when door opens? A faulty door switch is the likely cause. DIY repair takes about 30 minutes with basic tools.

Microwave not heating or starting? This door switch ensures proper door closure and circuit completion. DIY-friendly repair in about 15 minutes.

Replacement power cord for your microwave. Connects the appliance to your electrical outlet. Order a new cord if yours is frayed, damaged, or missing.

Microwave not cooling or fan not running? This motor drives the cooling fan to prevent overheating. DIY-friendly repair restores proper ventilation.

Restores interior and cooktop lighting in your microwave. Replace when bulb burns out or dims for clear visibility. Verify fit with your model number.

Fix a microwave that won't heat properly or shuts off early with a new temperature sensor. This part monitors internal temperature for safe operation.

Replace your microwave's mounting plate if it's cracked, bent, or missing. This structural component secures the microwave during installation.

Black cooktop assembly cover panel for microwaves. Replaces cracked, broken, or missing trim pieces. Restores the finished appearance of your unit.

Black cooktop cover for your microwave. Replaces cracked, broken, or missing covers. Restores the appearance of your appliance's cooktop area.

Glass cover for microwave hood lamp. Protects the light bulb from grease and debris. Replace if cracked, broken, or missing to restore proper lighting.

Controls airflow in your microwave's exhaust vent system. Installs between blower and duct. Replace if cracked, broken, sticking, or missing.

Glass turntable tray for microwaves. Replaces cracked, broken, or missing rotating platters. Installs on turntable support to hold dishes during cooking.

Charcoal filter removes smoke and odors in recirculating microwaves. Replace every 6-12 months or when odors persist. Verify fit with your model number.

Replace your worn or missing microwave door bushing. This small plastic component helps the door hinge operate smoothly and maintain proper alignment.

Secures your microwave door to engage the safety switches. Replace if the hook is cracked, broken, or worn, preventing the door from latching properly.

Secures your microwave to the wall or cabinet during installation. Replace this bracket if the original was lost, damaged, or missing during remodeling.

Fix a microwave that overheats or shuts off during use with this blower wheel replacement. Ensures proper ventilation and cooling. Easy 15-minute repair.

This clear light lens covers and protects the interior lamp, directing and diffusing light inside the appliance for better visibility. It replaces a cracked, yellowed, or missing lens to restore even interior illumination. What it does:

• Protects the interior lamp from spills, steam, and physical contact
• Diffuses and directs light for more even illumination inside the compartment
• Restores visibility when the original lens is cracked, cloudy, or missing
• Helps prevent direct contact with the bulb for safer operation

• Disconnect power to the appliance before starting any work
• Allow the bulb to cool completely before removing the old lens
• Handle the lens gently to avoid cracking; align tabs or clips and snap into place
• If the lens uses screws, tighten securely but do not overtighten to avoid cracking

Wall mounting bracket for over-the-range microwaves. Secures microwave to wall. Replace if bracket is bent, cracked, or missing for safe installation.

Support plate for microwave installation and mounting. Replaces cracked, broken, or missing support plates. Structural component for secure appliance positioning.

This replacement duct guides internal airflow to and from the appliance, restoring proper ventilation and helping the unit maintain even temperatures. Designed to match the original fit and routing for reliable performance. What it does:

• Channels conditioned or exhaust air through the correct internal path
• Helps prevent airflow restrictions that can cause uneven cooling or heating
• Reduces rattling or vibration from a damaged or misrouted air path
• Supports normal compressor/fan operation by maintaining intended ventilation

• One replacement duct as shown

• Inspect surrounding connectors and seals; replace damaged gaskets for best results
• Secure all fasteners to prevent air leaks
• Disconnect power (and water if applicable) before beginning work to avoid injury
• Avoid sharp bends that can restrict airflow

Replacement turntable support for your microwave. Installs under the glass tray to allow smooth rotation. Replace if cracked, broken, or worn out.

Replacement turntable support for your microwave. Mounts under the glass tray to enable smooth rotation. Order a new support if yours is cracked or broken.

This replacement identification label restores factory markings and safety/operating information on the appliance. It helps maintain readable instructions and regulatory info that have worn, peeled, or become unreadable. What it does:

• Replaces faded, torn, or missing identification and specification markings
• Restores safety warnings and operating instructions printed on the original label
• Helps service technicians and owners read model/serial and other printed information
• Prevents confusion from illegible markings and keeps appliance identification compliant

• One replacement identification label

• Clean and dry the mounting surface thoroughly before applying
• Peel backing and press label firmly in place to ensure full adhesion
• Avoid stretching or creasing the label during installation
• Remove adhesive residue from the old label with a mild cleaner and allow surface to dry

Charcoal air filter captures grease, smoke, and odors in over-the-range microwaves. Replace when performance declines. Confirm fit with your model number.

Traps grease and smoke from cooking. Replace when clogged or damaged to maintain ventilation efficiency. Verify compatibility with your model number.

Secures panels and components inside your microwave, keeping parts aligned and reducing rattles. Replace when clip is broken, cracked, or missing.

Replacement mounting screw for microwave ovens. Secures internal components and panels. Needed when original screws are stripped, missing, or damaged.

Mounting screw for microwave and wall oven assemblies. Replace if lost, stripped, or damaged during installation or service. Secures components.

Replacement mounting screw that secures panels, trim, and internal components in microwaves and wall ovens. Needed when screws are stripped, missing, or lost.

Screw secures the door latch and upper hinge plate on your microwave. Replace if missing, stripped, or loose to properly fasten door hinges and latch.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

This is a replacement information label used to display model, serial, wiring, and safety information on the appliance. It restores legible identification and safety markings so service and ownership details remain visible. What it does:

• Provides appliance identification and manufacturer information for service and records
• Displays safety warnings and basic operating or wiring notes as printed on the original
• Restores a worn, torn, or missing decal so important information is readable

• Clean and dry the mounting surface before applying for best adhesion
• Align carefully; labels are typically adhesive-backed and are not reusable once removed
• If servicing electrical components nearby, disconnect power before beginning work
• For exact placement, match the new label to the original location on the appliance

This replacement identification label provides the appliance's printed identification and specification info so you can model/serial and ratings at a glance. It restores missing or damaged factory markings for accurate identification. What it does:

• Displays printed identification and specification details used for service and parts lookup
• Helps model/serial and electrical or safety ratings typically found on the appliance
• Useful when original label is faded, torn, or missing and you need clear factory markings
• Keeps essential identification information visible for owners

• Clean and dry the mounting surface before applying; remove oils or residue
• Peel backing and press firmly; align carefully—adhesive is permanent
• Avoid stretching or creasing the label during installation