Parts for Frigidaire GMBS3068AFA: Oven Cabinet Parts

A complete refrigerator door assembly that replaces a damaged or dented door to restore proper closure, appearance, and insulation. Fits applicable Frigidaire refrigerator models and restores a secure seal for reliable cooling performance. What it does:

• Replaces a broken, dented, or warped refrigerator door to restore fit and function
• Provides the outer panel, inner liner, and mounting points needed for proper hinge and handle attachment
• Helps re-establish the door seal to reduce air leaks and improve temperature control
• Restores the appliance's appearance when the exterior door is cosmetically damaged

• Disconnect power and empty the door before removing the old unit; support the door—use a helper for safe lifting
• Retain or transfer any components the service manual specifies (handles, shelves, gaskets) only if explicitly shown to ship with this part
• Align hinges and fasteners per the manufacturer's instructions to ensure even door gap and proper sealing

This cover is a protective trim piece that shields and neatly finishes exposed components on your appliance. Replacing a cracked or missing cover restores protection and a clean, factory look while helping prevent accidental contact with internal parts.

• Conceals and protects wiring, mechanisms, or mounting hardware from dust and incidental contact
• Restores proper fit and finish for a clean appearance
• Helps ensure components remain secured and unobstructed
• Common symptoms include cracks, broken tabs, discoloration, or a missing/loose cover

• Disconnect power before servicing; shut off water supply if working near water lines
• Retain and reuse original screws or clips; transfer any clips from the old part if applicable
• Align tabs/slots and secure without overtightening to avoid damage
• The cover sits flush and doesn't interfere with doors, drawers, or moving parts

This adjustable leveling foot raises and stabilizes the appliance for proper alignment and even weight distribution. It restores a steady, wobble-free base so doors close correctly and the appliance sits level on uneven floors. What it does:

• Replaces a worn or damaged cabinet/console leveling foot to restore stable support
• Allows height adjustment to correct leaning or rocking on uneven surfaces
• Helps ensure doors and drawers close smoothly by keeping the appliance level
• Fits under the appliance base where a threaded/adjustable foot is required

• One adjustable leveling foot

• Turn the appliance off/unplug and empty lower compartments before accessing the foot
• Raise or support the appliance safely following manufacturer guidance before removal/installation
• Thread the foot into the mounting socket until it contacts the floor, then fine-tune the height for level

The Capacitor is an OEM part for Frigidaire microwaves. It is responsible for storing and releasing electrical energy to power the microwave's magnetron, which generates the high-frequency waves needed for cooking.

A bad capacitor can be caused by electrical issues, component failure, or physical damage. Signs of a faulty capacitor include microwave not heating properly, sparking or arcing inside the microwave, or unusual noises during operation.

Symptoms of a bad capacitor include:

• Microwave not heating  
• Sparking or arcing 
• Buzzing or humming sounds

Replace your malfunctioning or damaged capacitor with this genuine OEM Frigidaire part to restore your microwave. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Replacement electrical diode for Frigidaire refrigerators that directs current flow to protect control circuitry and help defrost and compressor systems operate correctly. Installs quickly to restore proper electrical function when a diode fails. What it does:

• Allows electrical current to flow in only one direction to protect sensitive control and compressor circuits.
• Prevents backfeed that can damage control boards or other components.
• Common symptom: intermittent or no compressor/defrost operation.
• Other symptoms: blown fuses, tripped breakers, or erratic electrical behavior in the appliance.

• Disconnect power to the appliance before beginning any service.
• Handle electrical connections carefully; use insulated tools and avoid touching live terminals.
• Confirm connector fit and orientation before finalizing installation.

This magnetron generates the microwave energy used to heat food in countertop and over-the-range microwaves. Replace a failed magnetron when the oven powers on but does not heat or shows arcing or loud humming. What it does:

• Converts high-voltage power into microwave radiation that heats food.
• Common symptom: microwave runs but does not heat.
• Other symptoms: unusually loud humming, arcing or sparking inside the cavity, or a burning/ozone-like smell.
• Not a user-serviceable electrical component — faults often require component-level replacement.

• Disconnect power before servicing; unplug the appliance and verify power is removed.
• Discharge the high-voltage capacitor before touching high-voltage components to avoid serious shock.
• Handle carefully; avoid touching the magnetron antenna or ceramic surfaces.

This replacement refrigerator water filter cartridge helps restore clean tasting water and ice by trapping common impurities. Designed as a direct-fit replacement to maintain your fridge's filtered water supply and improve taste clarity. What it does:

• Filters particulates and common contaminants to improve water and ice taste
• Helps reduce visible sediment and cloudiness from the dispenser and ice maker
• Restores normal dispensing performance when an old filter causes off-flavors or odors
• Supports consistent filtered water flow when installed and maintained

• Turn off the water supply and follow the refrigerator's filter-replacement instructions before starting
• Push/rotate or slide per your model's procedure until the filter locks in place; ensure a secure seal
• Run water through the dispenser for a short time after installation to flush air and initial carbon fines
• Replace regularly per the refrigerator manufacturer's recommendation or sooner if flow decreases or taste returns

This thermostat is a temperature-sensing switch that helps your appliance maintain the set temperature by opening and closing the circuit as conditions change. Replacing a weak or failed thermostat restores consistent cycling and stable performance. What it does:

• Monitors temperature and opens/closes its electrical contacts to control the circuit
• Helps the unit cycle on and off to maintain an even, target temperature
• A failed thermostat may cause temperature swings, short/long cycling, constant running, or no cycling at all

• 1 thermostat

• Disconnect power (and gas, if applicable) before servicing
• Access the thermostat location per your model; note wire positions and transfer any brackets/insulators from the original
• Make secure wire connections and route leads away from sharp, hot, or moving parts
• Reassemble covers, restore power, and verify proper cycling and temperature regulation

This temperature sensor monitors internal fridge/freezer temperature so the control board can regulate cooling and defrost cycles for more consistent temperatures and food safety. What it does

• Measures compartment temperature and sends readings to the control board.
• Helps the refrigerator maintain set temperatures by enabling accurate cooling cycles.
• Supports proper defrost control when used in defrost/evaporator applications.
• A failing sensor can produce temperature fluctuation, poor cooling, or longer run times.

• One temperature sensor

• Disconnect power before servicing to avoid shock or compressor damage.
• Handle the sensor and connector gently; avoid pulling on wires.
• Verify location and routing match the original; secure sensor to prevent contact with moving parts.

Replacement refrigerator thermostat that controls compressor on/off cycles to maintain the set cabinet temperature. Installs behind the control knob to restore consistent temperature regulation when the original thermostat fails. What it does:

• Regulates compressor cycling to keep the refrigerator at the selected temperature.
• Commonly needed when the fridge runs constantly, won't reach set temperature, or cycles on and off rapidly.
• Mounts into the control housing and connects to the existing wiring harness for direct replacement.
• Works with the appliance's built-in temperature control to stabilize interior temperatures.

• Disconnect power to the appliance before attempting any repair.
• Access the control housing by removing the control knob and trim; retain all mounting hardware.
• Match terminal locations and wiring before removing the old thermostat; install in the same orientation and secure firmly.

This bracket secures a component or panel within the appliance to keep it aligned and stable during operation. Replacing a cracked or missing bracket restores proper support and helps prevent vibration, rattling, or shifting.

• Provides a rigid mounting point for the original component or panel
• Maintains alignment so assemblies operate smoothly
• Replaces broken, warped, or missing hardware that causes looseness or noise
• Helps reduce vibration and rattling during use

• Disconnect power before servicing; shut off gas/water if applicable
• Note the original orientation and fastener locations; transfer any clips or spacers from the old bracket
• Reuse existing screws unless damaged; tighten evenly without overtightening
• Verify alignment and operation before reinstalling covers or panels

A push-button door switch that tells the appliance when the door is open or closed so lights, fans, or controls respond correctly. Replaces a worn or broken door-actuated switch to restore normal operation and interior lighting. What it does:

• Detects door open/closed position to control interior lights or related circuits
• Stops lights from staying on when the door is closed, preventing unnecessary power use
• Restores proper cycling of door-dependent functions and controls
• Commonly used when lights fail to turn on/off or when door-operated features are intermittent

• One replacement push-button door switch

• Disconnect power before servicing to avoid shock or damage
• Access typically requires removing interior trim or the light housing—keep fasteners for reassembly
• Verify switch orientation and terminal connections match the original before connecting

This infinite switch controls the heat level for an electric cooktop surface burner, restoring adjustable power to the element for even cooking and reliable temperature selection. What it does:

• Regulates electrical power to a single surface heating element so you can set low-to-high heat.
• Provides stepped "infinite" control positions rather than a simple on/off.
• Replaces a worn or failed control that causes a burner to not heat, stay stuck on one setting, or heat inconsistently.
• Uses standard spade-terminal connections found on many electric ranges.

• Disconnect power at the breaker before servicing—this part services live-voltage circuits.
• Access typically requires removing the cooktop or rear console; handle ceramic glass cooktops carefully to avoid cracking.
• Confirm terminal layout and mounting orientation before removal; take a photo of wiring for reassembly.

The Door Switch is an OEM part for Frigidaire microwaves. It plays a crucial role in the microwave's overall function by detecting when the door is open or closed. The door switch communicates this information to the control board, enabling it to safely operate the microwave's electronic components and magnetron when the door is shut.

Symptoms of a bad door switch include:

• The microwave failing to operate or function properly with the door closed  
• Inability to start or pause operation when the door is opened
• Error codes or failure messages appearing on the display related to door functionality

Causes of a bad door switch can be wear and tear over time, damage from repeated opening and closing of the microwave door, or impact from accidental mishandling. 

This OEM replacement is also compatible with Electrolux, Admiral, Crosley, White-Westinghouse, and Kenmore models.
 

This electrical wiring harness connects a refrigerator's control and power circuits so components receive reliable power and signals. It replaces a damaged or worn harness to restore proper electrical connections and reduce intermittent faults. What it does

• Routes power and signal lines between control board, compressor, fans, valves, and other internal components
• Restores lost or intermittent power caused by frayed wires, broken connectors, or corrosion
• Prevents shorts by replacing damaged insulation or connectors
• Supports proper operation of control-driven parts after replacement

• One electrical wiring harness as shown

• Disconnect power to the appliance before starting any work
• Inspect connector orientations and match keyed plugs before seating; do not force connectors
• Route harness along original cable paths and secure with clips or ties to prevent chafing

The fuse is a protective link in the appliance's power circuit. When excessive current or a short is detected, it opens the circuit to help safeguard wiring and electronics. A blown fuse often leaves the unit completely unresponsive.

• Interrupts power during an overcurrent or short to prevent further damage
• Helps protect control boards, motors, and wiring
• Typical symptoms: no power, blank display/controls, won't start
• Tests open (no continuity) when blown

• Disconnect power at the breaker or unplug before servicing
• Replace only with the same type and rating specified by the manufacturer
• If a new fuse blows again, locate and correct the underlying short or failed component before further use
• For microwave repairs, high-voltage capacitors can retain a dangerous charge.

Ring assembly that restores proper alignment and sealing where components meet in compatible Frigidaire appliances, helping stop leaks, reduce vibration, and support reliable operation by replacing worn or damaged rings. What it does:

• Provides a secure seal and proper fit between mating parts to reduce leaks or airflow loss
• Helps eliminate rattling or movement caused by a worn, cracked, or deformed ring
• Restores component alignment so controls and panels seat correctly
• Use when the original ring shows visible wear, cracks, warping, or is missing

• Disconnect power (or unplug) and shut off water/gas where applicable before beginning any repair
• Inspect surrounding parts and mounting surfaces; clean debris before installing the new ring
• Use appropriate hand tools and replace any fasteners that are damaged or corroded

This replacement tray restores a sturdy, level surface inside your appliance. Swap out a cracked or missing tray to keep items supported and organized, prevent tipping or spills, and bring back the intended fit and finish.

• Provides a stable platform for foods, containers, or accessories inside the appliance
• Restores proper fit when the original tray is cracked, warped, stained, or missing
• Helps resolve issues like items rocking, rattling, sliding, or the tray not seating level
• Designed to engage the appliance's existing supports for secure use

• Disconnect power to the appliance before servicing and remove items from the area
• Wear cut-resistant gloves; handle carefully to avoid chips, cracks, or cuts
• Note the original orientation; align and fully seat the new tray on the supports
• Inspect the supporting tabs/rails for bends or damage