Parts for Lg LMV1680ST: Oven Cavity Parts

This factory fastener secures appliance panels and components. Use it to replace a missing, stripped, or corroded screw so brackets, covers, and assemblies stay tight and properly aligned, helping reduce vibration and rattling.

• Secures panels, brackets, and internal components in their proper positions
• Replaces missing, worn, or cross-threaded hardware
• Helps eliminate vibration and rattling from loose parts
• Supports proper alignment of covers and assemblies

• Disconnect power to the appliance before servicing; allow any moving parts to stop
• Match this screw to the location shown in your model's parts diagram
• Start threads by hand to avoid cross-threading, then tighten snugly with the correct driver
• Do not overtighten to prevent stripping threads or cracking plastic bosses

A sheet-metal tapping screw used to fasten appliance panels and components where a self-threading fastener is needed. Replaces stripped or missing screws to restore secure fits and reduce rattling or loose trim. What it does

• Threads into thin metal or plastic mounting points to secure panels, brackets, and trim
• Commonly used where pre-formed threads are not available
• Helps stop vibrating or loose panels that cause noise or alignment issues
• Designed to grab and form threads as it's driven in for a tight hold

• Tapping screw

• Use the correct screwdriver bit to avoid cam-out or head damage
• Start straight and drive slowly until snug; avoid over-tightening which can strip or crack mounting material
• Disconnect power and remove nearby wiring or components as needed for safe access
• Wear eye protection when working with small fasteners and metal panels

This replacement door glass restores a clear viewing window and the protective barrier on your microwave door. Replace it when the original panel is cracked, shattered, or heavily scratched to keep the door secure and safe to use.

• Provides the see-through window and protective barrier within the microwave door
• Helps maintain proper door rigidity and alignment when intact
• Replace if the glass is cracked, chipped, shattered, loose, or badly scratched
• Reduced visibility, rattling, or visible damage are common symptoms of failure

• Unplug the microwave before servicing; microwaves can retain high voltage—use caution and do not open the cabinet
• Support the door; removal from the hinges may be required per your model's diagram
• Handle glass with cut-resistant gloves; edges can be sharp
• Transfer any reusable trim/clips as directed and verify the door latches and closes properly after installation

The Grease Filter is an OEM replacement part for LGmicrowaves. It plays a vital role in capturing grease, smoke, and odors generated during cooking, ensuring cleaner air in the kitchen. Regular cleaning or replacement of the microwave grease filter is essential for maintaining optimal airflow, filtration performance, and preventing potential fire hazards.

Causes of a bad grease filter include excessive use without proper cleaning, exposure to high temperatures or grease splatters, or simply reaching the end of its lifespan due to regular wear and tear.

Symptoms of a clogged or defective microwave grease filter:

• Reduced airflow or suction from the microwave ventilation system
• Unpleasant cooking odors lingering in the kitchen
• Visible buildup of grease or grime on the filter or surrounding areas
• Clogged or obstructed air vents or ductwork

This OEM LG part is also compatible with Sears/Kenmore microwaves.

The Light Bulb is an OEM part for LG microwaves. It provides illumination inside the microwave oven, allowing users to monitor the cooking process and check the condition of the food without opening the door.

Causes of a bad light bulb can include normal wear and tear, electrical surges, or damage due to impact or overheating. Over time, the filament inside the bulb can burn out, or the bulb itself can become loose or disconnected.

Symptoms of a bad light bulb include:

• The microwave interior light not turning on
• Flickering or dimming of the light
• Intermittent lighting during operation

This OEM LG part is also compatible with Sears/Kenmore models.

This canopy resistor regulates current to a range-hood or canopy fan circuit to help the blower run at the correct speeds. Replacing a failing resistor can restore proper fan speed control and stop intermittent operation. What it does:

• Controls electrical resistance in the canopy/blower circuit to help regulate fan speeds.
• Helps prevent the motor from running only on a single speed or from failing to start at selected speeds.
• Can cause symptoms such as inconsistent fan speeds, no response from speed controls, or occasional fan cutoff.
• Works with the hood's wiring and control switch to deliver the correct voltage to the fan motor.

• Disconnect power to the appliance before accessing the canopy or electrical connections.
• Inspect wiring and connectors for heat damage or corrosion; replace harness or terminals if damaged.

This replacement lamp socket holds the light bulb and provides a stable electrical connection so your appliance light works reliably. Replace a heat-damaged or loose socket to restore consistent illumination and help prevent flicker, arcing, and premature bulb failure.

• Secures the bulb and connects it to power
• Restores proper interior or work-area lighting
• Addresses flickering, intermittent light, or bulbs failing early from poor contact
• Replaces sockets that are cracked, melted, or discolored

• Disconnect power at the breaker or unplug before servicing
• Allow the area to cool; wear gloves and safety glasses
• Note wire positions and transfer one lead at a time to the new socket
• If servicing a microwave, access only the lamp area per your model instructions; do not open the cabinet—internal components can retain high voltage