Kenmore Washer 110.20872990 (11020872990, 110 20872990) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62889
Used for lid switch.
Do-It-Yourself Stories from Customers like You
Washer was "dead" with a partially washed load and would not do anything Jimmy M. • Hopewell , VA • September 19, 2014
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!)
Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts...
Read more
More
$16.77
- Compare At:
-
$19.79
- You Save:
-
$3.02
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3355454
This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.
- Applies tension to prevent rattling and buzzing during use
- Helps keep the mounted piece properly seated and aligned
- Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
- Simple, drop-in replacement where the original clip is used
What's included: 1 anti-rattle clip Install notes:
- Disconnect power to the appliance before servicing
- Note the original clip's orientation; transfer the new clip the same way
- Use needle-nose pliers for placement; avoid over-bending the clip
- The component is secure and clears adjacent parts before reassembly
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.
- Supports and centers the spin basket on the tub centerpost/drive shaft
- Provides a low-friction bearing surface to reduce wear and noise
- Helps maintain basket alignment and stability during spin
- When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin
What's included: 1 centerpost bearing Install notes:
- Disconnect power and water supply before servicing; use proper PPE
- Access typically requires removing the agitator, inner basket, and related drive components
- Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
- Seat the bearing fully and verify smooth basket rotation before reassembly
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3357319
Hose used from Valve to thermistor.
More
$19.79
- Compare At:
-
$22.10
- You Save:
-
$2.31
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3947517
This agitator assembly restores factory wash action in your top-load washer, driving clothes rollover and detergent circulation so loads clean evenly. Replace a cracked, loose, or slipping agitator to bring back reliable movement.
- Provides the back-and-forth motion that rolls clothes through the wash water
- Promotes even cleaning by circulating water and detergent
- Common symptoms: no or weak agitation; upper agitator freewheels in one direction; clicking/ratcheting during wash
- Also used when the agitator is visibly cracked, loose, or damaged
What's included: One agitator assembly Install notes:
- Disconnect power and turn off water supply before servicing
- If equipped, remove the fabric softener dispenser and cap to access the retaining bolt; lift the old agitator straight up
- Align splines, seat the new agitator fully, and reinstall the retaining bolt and cap
- Reuse any model-specific caps/dispensers and run a short test cycle to ensure proper agitation
Do-It-Yourself Stories from Customers like You
The agitator wasn't spinning Gerald B. • Anaheim Hills , CA • December 22, 2018
The bolt that holds the agitator and the agitator cam was rusted in place so it made the project way more difficult than it should have been. Had to cut the agitator off the shaft and cut the head of the frozen bolt off. Thankfully, Appliance Pros had all three parts I needed. Once the parts arrived it only took ten minutes to fix. Since the house was going to be full for Christmas, the fast shipping really, really helped. Was able to get it done before the guests arrived.
Read more
More
$90.95
- Compare At:
-
$108.23
- You Save:
-
$17.28
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2172937
This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:
- Holds three wiring terminals in the correct orientation for a mating connector
- Insulates and locks terminals to reduce arcing and overheating at the plug
- Replaces cracked, brittle, or heat-damaged connector housings
- Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched
What's included:
- 1 three-circuit connector housing
Install notes:
- Disconnect power before servicing the appliance
- Note wire/terminal positions and transfer them one at a time into the new housing
- Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
- Fully seat each terminal until it locks and the connector latch engages securely
More
$13.48
- Compare At:
-
$16.18
- You Save:
-
$2.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: 285666
Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138
Do-It-Yourself Stories from Customers like You
I was replacing the lid switch but decided to install a new vacuum break and drain hose while i was at it Dianne Z. • Manchester , CT • May 27, 2016
Just took off the old vacuum break and put the new one on. It was very easy because the site had a video showing how and I watched it first.
Read more
More
$44.95
- Compare At:
-
$53.49
- You Save:
-
$8.54
Genuine Whirlpool part
By: Whirlpool
Part Number: 285702
Size: 21 inches long. Clamp included.
Do-It-Yourself Stories from Customers like You
Drain hose too short and home depot fix leaked Sara B. • Liberty Hill , TX • August 21, 2015
Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly.
Now we're washing again and no leaks!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3360056
Used for the pressure switch.
Do-It-Yourself Stories from Customers like You
Broken lid switch Ari G. • State College , PA • June 01, 2015
Watched on line Video.
Only problem was in disconnecting wire "bus" connector from switch. I was unable to
remove connector without damaging it. I "jumped" connector to prove switch was faulty. This also allowed my wife to continue to do laundry while part arrived. I ordered a 3 circuit connector, but this was not the correct part. I ended up removing 3 wires from old broken connector and attaching them to new switch without a connector. Electrical tape did the trick. Not perfect...
Read more
More
$12.61
- Compare At:
-
$14.88
- You Save:
-
$2.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP54583
Right hand side. For screws use WPW10119828.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$19.50
- Compare At:
-
$23.20
- You Save:
-
$3.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10168257
$71.48
- Compare At:
-
$85.78
- You Save:
-
$14.30
Genuine Whirlpool part
By: Whirlpool
Part Number: WP72107
Color: Almond
Do-It-Yourself Stories from Customers like You
Broken meat drawer Jesse B. • Stow , MA • January 26, 2015
Replaced. Shippping was very fast. A good experience.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84