Kenmore Washer 110.26322500 (11026322500, 110 26322500) Parts

Straight knurled pin that secures knobs or small components to a shaft for a tight, slip-resistant fit. Replaces a worn or missing pin to stop loose, wobbly, or spinning knobs and restore reliable engagement. What it does:

• Secures knobs, dials or small parts to control shafts by providing a press-fit, knurled surface.
• Prevents wobble, slipping, or spinning of control knobs that won't turn with the shaft.
• Common service symptom: knob spins freely or fails to engage controls.
• Used where a small metal pin is required to lock a component onto a splined or smooth shaft.

• Disconnect power and unplug the appliance before servicing.
• Remove the knob or access panel to reach the shaft; pin is typically press-fit.
• Removal/installation may require needle-nose pliers, a small punch, or a bench press; protect surrounding parts from damage.
• Keep small parts away from children and follow appliance safety guidelines; replace mating hardware if the shaft or hole is damaged.

Includes suspension pads.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.

Replacement console strap that secures the appliance control panel to the cabinet, restoring stable console alignment and preventing the control panel from shifting or sagging during use for safer, neater operation. What it does:

• Secures the control console to the cabinet to prevent wobble, tilt, or separation.
• Replaces a worn or broken strap commonly causing a loose or misaligned control panel.
• Helps reduce strain on control harnesses and connectors that can occur when the console moves.
• Matches OEM fit so the console remains properly seated and functional.

• Disconnect power to the appliance before beginning any repair.
• Typically accessed by removing the console or control panel; retain all screws and clips for reassembly.
• Use common hand tools (screwdriver, nut driver) and follow the model-specific service manual for exact steps.
• If wiring connectors are disturbed, verify secure connections before restoring power.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

This drain hose clamp secures the hose connection to keep water where it belongs during the drain cycle. A tight, reliable clamp helps prevent leaks and hose pull-off from vibration or pressure changes. What it does:

• Secures the drain hose to a pump outlet or drain port to maintain a watertight seal
• Helps prevent the hose from slipping off during operation
• Reduces leaks at the hose connection point
• Common symptoms of a bad clamp: water leaking at the drain hose joint, a loose/detached hose, or a visibly rusted/broken clamp

• 1 clamp

• Disconnect power and turn off the water supply; place a towel to catch residual water
• Access the hose connection, remove the old clamp, and inspect the hose end and fitting; replace the hose if cracked or swollen
• Position the new clamp correctly over the hose and behind the fitting bead; tighten/seat evenly without overtightening
• Reassemble and run a brief drain test to check for leaks

This replacement refrigerator door hinge keeps the door aligned and operating smoothly so your appliance seals and closes properly. It restores proper door movement and helps prevent drafts and uneven wear. What it does:

• Supports the refrigerator door and maintains correct alignment for a tight seal
• Allows smooth opening and closing of the door without binding
• Helps prevent door sag, rubbing, or gaps that can cause temperature issues
• Fits where the original hinge mounts to the cabinet or door depending on model

• Disconnect power and remove contents from the door before starting work
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use the original fasteners or OEM-recommended hardware; tighten screws securely but avoid over-torquing

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This spring damper assembly cushions and stabilizes the appliance drum during spin cycles, reducing vibration and helping maintain smooth, balanced operation. It restores proper drum support and motion control for safer, quieter performance. What it does:

• Absorbs and dampens drum movement to reduce vibration and banging during spin
• Helps keep the drum properly aligned to prevent wobbling or rubbing
• Can resolve symptoms such as loud thumping, excessive vibration, or uneven spinning
• Works as the suspension support between the drum and cabinet to improve cycle stability

• Disconnect power (and water, if applicable) before beginning any repair
• Handle springs and mounting points carefully—springs are under tension and can snap if released improperly
• Installation may require partial disassembly of the cabinet or drum; follow the OEM service manual or instructions

This agitator cap covers the top of the washer agitator, restoring the finished appearance and helping keep the agitator post and fastener protected from lint and moisture. Ideal for replacing cracked, faded, or missing caps. What it does:

• Covers the agitator retaining bolt/fastener to reduce exposure and debris buildup
• Helps prevent fabric from snagging on an exposed agitator top
• Restores finished look to the agitator after damage or wear
• Useful when the original cap is cracked, broken, or discolored

• Disconnect power to the washer before servicing.
• This cap typically snaps into place or fits over the agitator post; some models require partial agitator removal.
• Use basic hand tools if agitator removal is necessary; avoid forcing plastic parts to prevent breakage.

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

This replacement sleeve fits over a rotating shaft to reduce friction and protect the mating surface, helping restore smooth operation and reduce noise. Use when a worn sleeve causes rubbing or uneven movement. What it does:

• Acts as a bushing to prevent metal-to-metal contact on a rotating shaft
• Reduces friction and wear on the shaft and surrounding components
• Helps stop rubbing, scraping, or squeaking noises caused by a worn sleeve
• Restores proper alignment for smoother, quieter operation

• Disconnect power (and gas, if applicable) before starting any repair
• Use basic hand tools; no special training required for most installations
• Inspect the shaft and mating surfaces; replace if excessively scored or damaged
• If press-fit, install carefully to avoid damaging the new sleeve; do not use solvents as a substitute for proper fit

This E ring is a small metal retaining clip that secures shafts, pulleys, and other rotating parts to prevent axial movement. It restores correct part positioning so assemblies run smoothly and stay aligned. What it does:

• Acts as a snap/retaining ring to hold components on a shaft or in a groove
• Prevents pulleys, bearings, or spacers from sliding out of place
• Common symptom: loose or shifting pulley, increased wobble, noise, or component disengagement
• Small, inexpensive part whose failure can allow adjacent parts to migrate and cause additional damage

• Disconnect power to the appliance before beginning any repair
• Use snap-ring pliers or needle-nose pliers and wear eye protection when installing or removing
• Ensure clip seats fully in the shaft groove and that mating surfaces are clean and undamaged
• Replace any damaged mating hardware rather than reusing a deformed clip

For end of drain hose.