Kenmore Washer 110.26702690 (11026702690, 110 26702690) Parts

Left hand side.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.

This small hardware washer is used as a spacer and load distributor within the specified assembly. It helps maintain alignment and smooth operation by reducing friction and restoring a secure fit when the original washer is worn or missing. What it does:

• Distributes load under a screw or bolt to keep joints secure
• Maintains proper spacing and alignment between mating parts
• Reduces friction and wear at the contact surface
• Replace if missing, bent, cracked, or excessively worn; clues include wobbly parts or scraping/squeaking noises

• 1 washer

• Disconnect power and shut off water supply before servicing
• Refer to your model's parts diagram for exact location and stack order
• Clean mating surfaces; replace any damaged fasteners or bushings
• Tighten hardware evenly and do not overtighten

Replacement end cap that restores the appliance's finished edge and helps protect internal components from debris. A simple, low-cost repair to replace cracked, broken, or missing end caps and reduce trim wear. What it does:

• Covers and protects an exposed edge or end of the cabinet/trim.
• Helps prevent snagging, dirt buildup, and contact damage where the cap is missing or cracked.
• Restores the appearance and alignment of surrounding trim pieces.
• Common symptom: visible crack, loose or missing trim, rubbing or catching at the edge.

• Disconnect power and/or water supply to the appliance before beginning work when applicable.
• Inspect the mating surface and remove old adhesive or fasteners before installing the replacement cap.
• Install by aligning the cap and snapping or fastening into place; do not force—use correct fasteners if applicable.
• If surrounding trim is damaged, consider replacing affected pieces to ensure proper fit and finish.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This spring damper assembly cushions and stabilizes the appliance drum during spin cycles, reducing vibration and helping maintain smooth, balanced operation. It restores proper drum support and motion control for safer, quieter performance. What it does:

• Absorbs and dampens drum movement to reduce vibration and banging during spin
• Helps keep the drum properly aligned to prevent wobbling or rubbing
• Can resolve symptoms such as loud thumping, excessive vibration, or uneven spinning
• Works as the suspension support between the drum and cabinet to improve cycle stability

• Disconnect power (and water, if applicable) before beginning any repair
• Handle springs and mounting points carefully—springs are under tension and can snap if released improperly
• Installation may require partial disassembly of the cabinet or drum; follow the OEM service manual or instructions

This 3-position temperature switch is the user control that selects between three temperature settings, restoring reliable temperature selection and consistent performance. It replaces a worn or failed selector to recover intended temperature control. What it does

• Acts as the selector that routes the control signal to one of three temperature positions.
• Commonly used when temperature settings fail to change or the unit stays at one setting.
• Helps eliminate inconsistent temperatures or intermittent heating/cooling related to selector faults.
• Switches between preset temperature ranges without changing other controls.

• One 3-position temperature switch

• Disconnect power to the appliance before beginning any work.
• Note or label wire locations and take a photo before removing the old switch for correct reassembly.
• Handle connectors carefully; ensure secure, fully seated connections after installation.

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

This replacement sleeve fits over a rotating shaft to reduce friction and protect the mating surface, helping restore smooth operation and reduce noise. Use when a worn sleeve causes rubbing or uneven movement. What it does:

• Acts as a bushing to prevent metal-to-metal contact on a rotating shaft
• Reduces friction and wear on the shaft and surrounding components
• Helps stop rubbing, scraping, or squeaking noises caused by a worn sleeve
• Restores proper alignment for smoother, quieter operation

• Disconnect power (and gas, if applicable) before starting any repair
• Use basic hand tools; no special training required for most installations
• Inspect the shaft and mating surfaces; replace if excessively scored or damaged
• If press-fit, install carefully to avoid damaging the new sleeve; do not use solvents as a substitute for proper fit

This E ring is a small metal retaining clip that secures shafts, pulleys, and other rotating parts to prevent axial movement. It restores correct part positioning so assemblies run smoothly and stay aligned. What it does:

• Acts as a snap/retaining ring to hold components on a shaft or in a groove
• Prevents pulleys, bearings, or spacers from sliding out of place
• Common symptom: loose or shifting pulley, increased wobble, noise, or component disengagement
• Small, inexpensive part whose failure can allow adjacent parts to migrate and cause additional damage

• Disconnect power to the appliance before beginning any repair
• Use snap-ring pliers or needle-nose pliers and wear eye protection when installing or removing
• Ensure clip seats fully in the shaft groove and that mating surfaces are clean and undamaged
• Replace any damaged mating hardware rather than reusing a deformed clip

For end of drain hose.

This hose coupling connects a flexible appliance hose to the appliance plumbing, restoring a secure water connection and preventing leaks. Ideal when a worn or damaged coupling causes drips or loose hose fit. What it does:

• Provides a secure connection point between an appliance hose and the appliance inlet
• Replaces cracked, broken or corroded couplings that can leak or allow the hose to detach
• Restores proper hose sealing to reduce water drips at the connection
• Compatible with the original inlet connection type and mounting orientation

• Turn off and disconnect appliance power and shut off the water supply before replacing
• Remove the old coupling and clean the mating surfaces; inspect hose and clamps for wear
• Use proper clamps and hand-tighten; avoid over-tightening which can damage fittings