Kenmore Washer 110.27072602 (11027072602, 110 27072602) Parts

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This adjustable leveling leg helps stabilize and properly level your appliance on uneven floors. Replacing a worn or missing leg reduces wobble and vibration so doors align and the unit operates smoothly.

• Screws into the base to raise or lower a corner for precise leveling
• Helps prevent rocking, vibration, and rattling during use
• Promotes even weight distribution to protect the cabinet and flooring
• Restores proper door/drawer alignment once the unit is level

• Disconnect power; shut off water supply before servicing
• Carefully pull or tip the appliance to access the leg; use a helper for safety
• Start threads by hand, then adjust height with a wrench—do not over-extend
• Verify level front-to-back and side-to-side; recheck after moving or loading

Suspension rod ball and bushing kit includes 4 balls and 4 bushings.

This washer lid assembly covers the tub opening and engages the lid switch for safe operation. Replacing a damaged lid restores proper closure, helps prevent splashing, and ensures spin cycles start when the lid is shut.

• Covers the washer opening to contain water and laundry during operation
• Actuates the lid switch/lock so the machine can run and spin when closed
• Maintains proper hinge alignment and cabinet fit at the top of the unit
• Common symptoms: cracked or bent lid, broken hinge area, lid won't close or align, washer won't start or spin unless pressing on the lid

• Unplug the washer before servicing; move the unit carefully to avoid damage
• Support the lid and remove hinge screws carefully to prevent drops or chips
• Transfer any hinge bushings, pins, or bumpers from the old lid if required
• After installation, verify the lid switch/lock engages and the lid closes evenly

Color: White

This valve controls the flow of water into the appliance. When energized, it opens to let the correct amount of water in; when de-energized, it closes to stop flow—restoring proper fill and dependable operation. What it does:

• Opens and closes to regulate incoming water during operation
• Helps maintain correct fill levels for cycles
• Common symptoms of a failing valve: no fill or slow fill, error codes related to water supply, dripping/leaks from the valve area, or humming/clicking with little to no water flow

• 1 valve assembly

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Label and transfer hoses/wires one at a time; reuse existing hardware/fittings
• Restore water and power, then check all connections for leaks and run a test cycle

Used from harness to top.

Size: .20 Fl. Oz. (6 ml)

This lid hinge bearing supports the washer lid at the pivot so it opens and closes smoothly. When worn or broken, the lid may squeak, bind, or sit misaligned. Replacing the bearing restores smooth, stable lid operation. What it does:

• Provides a low-friction pivot surface for the lid hinge pin
• Helps keep the lid aligned and supported during opening/closing
• Can address squeaking, stiffness/binding, wobble, or a loose/uneven lid
• Replaces cracked or missing hinge bushings at the lid pivot

• 1 lid hinge bearing

• Disconnect power and, if applicable, shut off water supply before servicing
• Support the lid to prevent strain on hinges while removing hardware
• Remove hinge fasteners/pivot pin, replace the bearing in the lid hinge pocket, and reassemble
• Inspect the opposite hinge/bearing and replace as needed for even action

• Many washers use one bearing per hinge; order the quantity your model requires.

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

Color: White

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Screw for control panel.

This top spring hinge provides the tension and pivot point that helps a laundry appliance door open and stay aligned for smooth operation. It restores proper door positioning and reduces sag or uneven closing. What it does:

• Replaces a worn or broken top spring hinge to restore door tension and alignment
• Helps prevent the door from sagging, sticking, or closing unevenly
• Restores consistent opening/closing motion and proper seal engagement
• Addresses symptoms such as a drooping door, noisy hinge movement, or difficulty keeping the door open

• Disconnect power and, if applicable, gas supply before beginning any repair
• Follow the appliance manufacturer's instructions; some models require door removal to access the top hinge
• Use proper hand tools and retain all fasteners; wear gloves and eye protection
• If both hinges show wear, consider replacing both to ensure balanced tension

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps