Kenmore Washer 110.27152602 (11027152602, 110 27152602) Parts

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This adjustable leveling leg helps stabilize and properly level your appliance on uneven floors. Replacing a worn or missing leg reduces wobble and vibration so doors align and the unit operates smoothly.

• Screws into the base to raise or lower a corner for precise leveling
• Helps prevent rocking, vibration, and rattling during use
• Promotes even weight distribution to protect the cabinet and flooring
• Restores proper door/drawer alignment once the unit is level

• Disconnect power; shut off water supply before servicing
• Carefully pull or tip the appliance to access the leg; use a helper for safety
• Start threads by hand, then adjust height with a wrench—do not over-extend
• Verify level front-to-back and side-to-side; recheck after moving or loading

Suspension rod ball and bushing kit includes 4 balls and 4 bushings.

Used from harness to top.

This lid hinge bearing supports the washer lid at the pivot so it opens and closes smoothly. When worn or broken, the lid may squeak, bind, or sit misaligned. Replacing the bearing restores smooth, stable lid operation. What it does:

• Provides a low-friction pivot surface for the lid hinge pin
• Helps keep the lid aligned and supported during opening/closing
• Can address squeaking, stiffness/binding, wobble, or a loose/uneven lid
• Replaces cracked or missing hinge bushings at the lid pivot

• 1 lid hinge bearing

• Disconnect power and, if applicable, shut off water supply before servicing
• Support the lid to prevent strain on hinges while removing hardware
• Remove hinge fasteners/pivot pin, replace the bearing in the lid hinge pocket, and reassemble
• Inspect the opposite hinge/bearing and replace as needed for even action

• Many washers use one bearing per hinge; order the quantity your model requires.

Size: .20 Fl. Oz. (6 ml)

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

Color: White

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Screw for control panel.

This top spring hinge provides the tension and pivot point that helps a laundry appliance door open and stay aligned for smooth operation. It restores proper door positioning and reduces sag or uneven closing. What it does:

• Replaces a worn or broken top spring hinge to restore door tension and alignment
• Helps prevent the door from sagging, sticking, or closing unevenly
• Restores consistent opening/closing motion and proper seal engagement
• Addresses symptoms such as a drooping door, noisy hinge movement, or difficulty keeping the door open

• Disconnect power and, if applicable, gas supply before beginning any repair
• Follow the appliance manufacturer's instructions; some models require door removal to access the top hinge
• Use proper hand tools and retain all fasteners; wear gloves and eye protection
• If both hinges show wear, consider replacing both to ensure balanced tension

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This dispenser assembly delivers and routes detergent during the wash cycle so your washer dispenses the right cleaning agent at the right time. Replaces a cracked, clogged, or non-sealing detergent dispenser to restore normal detergent flow. What it does:

• Holds and meters liquid or powder detergent so it enters the wash at the proper cycle
• Prevents detergent from leaking into the tub between cycles when the dispenser door is closed
• Helps avoid clogs or buildup that can keep detergent from dispensing
• Restores proper dispenser door operation if the door is cracked, warped, or broken

• One detergent dispenser assembly

• Disconnect power to the appliance before beginning any repair
• Remove the control panel or cabinet access per your model's service instructions to reach the dispenser
• Handle clips and wiring gently; note or photo connector locations before disconnecting
• After installation, restore power and run a short cycle to confirm proper dispensing and no leaks