Kenmore Washer 110.47511702 (11047511702, 110 47511702) Parts

Note: This is a kit of 4 shipping bolts.

This pulley is part of your appliance's belt-drive system. It provides a smooth, low-friction surface for the drive belt and helps keep it tracking correctly so the motor can transfer power reliably to the drum or tub.

• Guides the drive belt and rotates freely to reduce friction and wear
• Helps maintain proper belt alignment for consistent operation
• Worn pulley symptoms can include squealing/squeaking, grinding or wobble, belt fraying or coming off, and little or no drum/tub movement
• If noise or belt damage persists, inspect the belt, tensioner/idler components, and rollers/bearings

• Disconnect power and, if applicable, shut off gas before servicing
• Access the drive path and note belt routing before removal
• Relieve belt tension, remove the old pulley, and transfer any spacers/retainers as needed
• After installation, spin the pulley by hand to ensure smooth, quiet rotation; replace a worn belt at the same time

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

This control knob replaces a worn or broken range/oven front knob to restore tactile control and clear temperature/setting selection. It gives a secure fit so you can safely set burners or oven functions. What it does:

• Replaces a damaged or missing control knob to restore manual control of burners or oven settings
• Provides a clear pointer for accurate selection of heat levels and functions
• Snaps on to the stove/range control shaft for reliable operation
• Helps eliminate slipping, stripped splines, or loose turning caused by a worn knob

• One control knob as shown

• Turn power and gas supply off before servicing; follow appliance safety guidance
• Pull off the old knob straight from the control shaft and push the replacement fully onto the shaft until it seats
• If knob does not fit, do not hammer or modify the shaft

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This tub clamp secures a flexible seal or hose to the appliance's tub, maintaining a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop leaks and keep the tub joint stable during operation.

• Applies even clamping pressure around the tub connection
• Helps prevent water leaks at the tub-to-seal or tub-to-hose joint
• Restores proper fit when the original clamp is stretched, stripped, corroded, or missing
• Common symptoms: water at the base/front, loose seal or hose, visible clamp damage

• Disconnect power and turn off water before service
• Access the tub connection; remove the old clamp and inspect the seal/hose for wear
• Clean mating surfaces; seat the seal evenly, position the clamp, and tighten until snug without pinching the rubber
• Run a quick fill/drain test and check for leaks

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This is a replacement mounting screw used to secure panels and internal components on compatible Whirlpool appliances. It restores proper fastening where the original screw is missing, stripped, or damaged for a safe, snug fit. What it does:

• Secures panels, brackets, or small components to the appliance chassis
• Restores lost or damaged fasteners that cause rattling or looseness
• Helps maintain correct alignment of parts that rely on threaded fastening
• Prevents further wear by replacing stripped or corroded screws

• Use the matching screw length and thread engagement; do not force if resistance is encountered
• Tighten firmly but avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow manufacturer safety instructions before servicing
• Consider replacing all matching fasteners for uniform fit

This transport cover secures internal components during shipping and service to prevent movement and damage. It helps keep parts aligned and reduces noise caused by loose components while the appliance is being moved. What it does:

• Holds internal components in place during transport to prevent shifting or impact damage
• Reduces rattles and vibration caused by unsecured parts
• Protects delicate assemblies from knocks during delivery or handling
• Helps maintain alignment of components until the appliance is installed

• One transport cover

• Disconnect power and water before servicing the appliance
• Remove all shipping brackets and covers per the owner's manual before normal operation
• Use manufacturer-specified fasteners and torque; do not force or modify the part

This wire harness connects the motor to the appliance's power and control wiring, restoring reliable electrical connection for motor operation. It replaces a damaged or worn harness to help restore normal motor function. What it does

• Carries power and control signals between the motor and the main wiring harness or control board
• Can resolve intermittent motor operation, no-start conditions, or loss of motor power when the fault is a damaged connector or wiring
• Replaces frayed, burned, or broken wires and damaged connector ends that prevent proper motor function
• Helps prevent arcing and poor connections that can cause overheating or electrical faults

• One motor wire harness

• Disconnect power to the appliance before beginning any repair to avoid electrical shock
• Verify the harness matches the original by comparing connector shapes and pin count before installation
• Route and secure the harness away from moving parts and sharp edges; use existing clips or ties
• If you see damage to the motor or control board connectors, inspect those components and replace as needed

This rivet secures panels, trim, or small components on compatible Whirlpool appliances to restore proper fit and reduce noise. It's a simple replacement for worn, loose, or missing fasteners so parts stay firmly in place. What it does:

• Holds appliance panels, brackets or trim pieces together for a secure fit
• Stops rattling or vibration caused by loose or missing fasteners
• Restores proper alignment of parts that rely on a permanent fastener
• Provides a durable, low-profile connection where a rivet was originally used

• Turn off and unplug the appliance before working on it to avoid shock or injury
• Remove the damaged rivet by drilling or cutting; install new rivet with the proper rivet tool or replacement method for the original rivet type
• Wear eye protection and follow basic hand-tool safety

This supporting clamp secures hose or component assemblies to help prevent movement and wear. It restores proper routing and restraint so hoses and wiring stay in place during normal operation. What it does:

• Holds hoses, tubes or small wiring bundles in position to reduce rubbing and chafing
• Prevents strain on connections that can cause leaks or intermittent electrical issues
• Keeps components aligned for reliable operation and quieter performance
• Useful when original clamp is cracked, broken, or no longer grips securely

• One supporting clamp

• Inspect mating surfaces and replace any damaged hoses or fasteners before installing
• Use appropriate hand tools; avoid over-tightening which can deform the clamp or hose
• Disconnect power and turn off water supply when working near electrical or plumbing connections

This drive motor powers the washer's agitation and spin functions so loads clean and drain properly. Replaces a failed or noisy motor to restore normal drum movement and cycle operation. What it does:

• Turns the transmission/drum to enable agitation and spin cycles
• Restores rotation when the washer won't spin or agitate
• Stops symptoms like grinding, loud noise, or motor humming during cycles
• Works with the appliance's driveline and wiring harness to transfer power

• One drive motor

• Disconnect power before starting and follow all safety precautions
• Handle carefully—motor and mounting hardware may be heavy or awkward
• Verify electrical connections and mounting alignment during reassembly

Rubber bumper. Color: Grey.

This outer tub is the dishwasher's main outer wash tub shell that helps contain water and support internal components. Replacing a damaged outer tub restores the cabinet seal and helps stop leaks and moisture damage. What it does

• Houses and supports the inner tub, pump, and other internal components.
• Contains wash water to prevent leaks from reaching the cabinet or flooring.
• Helps maintain proper alignment for spray arms and seals to function.
• Commonly replaced when the tub is cracked, warped, or allowing water to escape.

• One outer tub.

• Disconnect power and water before starting; follow OEM disassembly steps for your model.
• Replacement typically requires removing the dishwasher door, control console, and interior components; keep fasteners organized.
• Inspect and replace gaskets, seals, and mounting hardware as needed for a watertight repair.