Kenmore Washer 110.47511702 (11047511702, 110 47511702) Parts

This clamp secures flexible hoses and small-diameter tubing to fittings, helping prevent leaks and maintain proper fluid flow in appliance systems. It's a simple replacement that restores a tight, reliable connection. What it does

• Holds a hose or tube firmly on a barb or nipple to stop leaks and loss of pressure
• Keeps water, drain, or vent hoses seated during normal appliance operation
• Replaces worn, corroded, or loose clamps that cause dripping or poor connections
• Works where a small, durable clamp is required for routing or securing tubing

• One hose clamp

• Inspect hose and fitting for damage; replace hose if cracked or hardened before installing the clamp
• Tighten clamp until snug—do not overtighten; ensure even compression around the hose
• Disconnect power and water as appropriate and take safety precautions before working on the appliance

This clamp secures a flexible appliance hose to a fitting to help prevent leaks and keep connections tight. It's a small but essential part that restores a proper seal on water or drain lines. What it does:

• Holds a hose firmly to a tailpiece, barb or connector to reduce leaks and hose slippage
• Helps stop intermittent dripping or pooling caused by loose hose connections
• Restores a proper seal after hose replacement or maintenance
• Works on common appliance water/drain lines where this clamp style is used

• One hose clamp

• Disconnect power and shut off water to the appliance before starting any work
• Allow the appliance and hoses to cool if recently used; use gloves and eye protection
• Use appropriate pliers or a screwdriver (depending on clamp style) to remove and install the clamp; avoid over-tightening
• Inspect the hose and fitting for damage; replace the hose if cracked or worn

This replacement screw secures appliance panels and trim so components stay properly aligned and vibration is reduced. Use it to replace missing or damaged fasteners and restore a secure fit for safe operation. What it does:

• Fastens control panels, trim pieces, or access panels to the appliance frame
• Prevents panel movement, rattling, or gaps that can form from loose or missing screws
• Restores proper alignment after service or part replacement
• Helps maintain safe, stable operation by keeping panels secured

• Disconnect power (and gas if applicable) before servicing the appliance
• Use the correct driver bit and thread engagement; hand-start threads to avoid cross-threading
• Do not overtighten — snug until secure to avoid stripping or damaging panel threads
• Keep removed hardware organized to ensure correct locations during reassembly

The Vent Hose is an OEM part for Whirlpool washing machines. This vent hose allows air to circulate in and out of the washer, preventing pressure build-up and ensuring proper water drainage. It helps maintain the efficiency and effectiveness of the washing machine by facilitating the necessary airflow during the wash and spin cycles.

Common causes of a bad vent hose include wear and tear from regular use, blockages from lint or debris, and damage from mishandling or improper installation.

Symptoms of a bad vent hose include:

• Water not draining properly from the washer
• Unusual noises during the wash or spin cycles
• Leaks or water pooling around the washer
• Visible cracks, splits, or blockages in the hose

This OEM part is also compatible with some Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Connector lever

This rubber seal fits around the water temperature sensor where it passes through the tub or housing. It restores a watertight barrier at the sensor port to help prevent leaks and ensure reliable temperature feedback.

• Creates a watertight seal around the temperature sensor
• Helps prevent drips or leaks from the sensor opening
• Supports stable, accurate temperature readings during cycles
• Typical failure signs: cracked, flattened, or brittle seal; moisture at the sensor area; pooling water beneath the unit; temperature-related faults

• Disconnect power and turn off water supply before servicing
• Access the sensor location and drain any remaining water
• Withdraw the sensor, remove the old seal, and clean the seating surface
• Lightly moisten the new seal with water, seat it fully, reinstall the sensor, and check for leaks during a test cycle

This distribution nozzle directs water flow inside the dishwasher to help ensure proper spray coverage and detergent/rinse aid distribution. Replacing a damaged nozzle restores targeted water delivery for better cleaning and drying performance. What it does:

• Directs and shapes spray from the wash assembly for targeted cleaning
• Helps distribute rinse aid/detergent where designed for optimal results
• Prevents leaks or misdirected spray caused by cracks or clogs
• Faulty nozzles can cause poor cleaning, spotting, or uneven wash performance

• Disconnect power and water supply before beginning any repair.
• Inspect surrounding spray arm/assembly for damage or debris before installation.
• Most installs are a snap-fit or secured with simple fasteners; avoid over-tightening.

This counterweight helps balance and stabilize a refrigerator door so it opens and closes smoothly and stays in the desired position. It replaces a worn or damaged weight to restore proper door operation. What it does:

• Adds counterbalance to a fridge door so it doesn't slam shut or drift open
• Restores even, controlled door movement and alignment
• Helps reduce stress on door hinges and seals
• Commonly replaced when the door feels heavy on one side or won't stay open

• One counterweight

• Disconnect power to the appliance before beginning any repair
• Support the door while removing/installing the counterweight to avoid injury or damage
• Basic hand tools may be required; refer to your service manual for exact steps

This programmed central control board manages the appliance's main functions and user interface, restoring cycle control and electronic operation when the original control fails. Use this board to replace a faulty or unresponsive main control. What it does

• Interprets control panel inputs and runs timed cycles and sequences
• Controls power to motors, valves, heaters and other subsystems as commanded
• Restores normal electronic control when the original board stops responding
• Clears or prevents errors tied to a failed main control board

• One programmed central control board

• Disconnect power before servicing to avoid shock or damage
• Handle the board by its edges and avoid static; ground yourself before touching
• Reinstall mounting hardware and wiring exactly as removed; label connectors if needed
• Follow OEM service instructions

This oven door glass replaces a cracked or broken glass panel so the door seals and you can safely see inside while cooking. It restores the oven door's protective barrier and appearance. What it does:

• Replaces damaged or cracked oven door glass to prevent heat loss and sharp edges
• Restores visibility into the oven cavity for safe monitoring of food
• Helps the door maintain proper sealing when paired with intact gaskets and hardware
• Reduces risk of glass shards or injury from a compromised panel

• Handle with care; glass is fragile—use gloves and eye protection during removal and installation
• Disconnect power and allow the oven to cool before working on the door
• Follow the oven manufacturer's instructions for removing the door and fastening the glass
• If door hardware or seals are damaged, inspect and replace them separately