Kenmore Washer 110.47532604 (11047532604, 110 47532604) Parts

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

This control knob replaces a worn or broken range/oven front knob to restore tactile control and clear temperature/setting selection. It gives a secure fit so you can safely set burners or oven functions. What it does:

• Replaces a damaged or missing control knob to restore manual control of burners or oven settings
• Provides a clear pointer for accurate selection of heat levels and functions
• Snaps on to the stove/range control shaft for reliable operation
• Helps eliminate slipping, stripped splines, or loose turning caused by a worn knob

• One control knob as shown

• Turn power and gas supply off before servicing; follow appliance safety guidance
• Pull off the old knob straight from the control shaft and push the replacement fully onto the shaft until it seats
• If knob does not fit, do not hammer or modify the shaft

This motor-drive assembly powers the appliance's drive system to rotate the tub or drum so cycles run correctly. Replacing a worn or failed motor helps restore normal spinning and agitation for proper cleaning and drying. What it does:

• Converts electrical power into mechanical rotation to drive the tub/drum during operation
• Engages during spin/agitate cycles to move laundry and maintain cycle performance
• Helps maintain correct speed and torque required for load movement
• Failing unit can cause no spin, slow or inconsistent rotation, or unusual noises

• Disconnect power (unplug or turn off breaker) before starting any repair
• Handle unit and wiring harness carefully; verify connectors seat fully during reassembly
• Follow the appliance service manual for disassembly steps and torque/spec guidance
• If you detect burnt wiring or damaged mounting hardware, replace those items before operation

This electronic control board manages the appliance's timing, display, and user inputs so cycles run correctly and settings respond. Replacing a faulty control restores normal operation when the console is unresponsive or cycles behave erratically. What it does:

• Receives and processes user commands from the console and relays signals to motors, heaters, valves, and other components.
• Controls cycle timing, option selections, and display/status indicators.
• Works as the appliance's main logic/control module; it does not include sensors or external switches unless specified.

• One electronic control board

• Always disconnect power (unplug or shut off breaker) before servicing to avoid shock or damage.
• Handle the board by its edges and avoid static discharge—use a grounded strap if available.
• Some installations require removing the console or access panel and careful routing of wiring—refer to the service manual or wiring diagram.

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This tub clamp secures a flexible seal or hose to the appliance's tub, maintaining a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop leaks and keep the tub joint stable during operation.

• Applies even clamping pressure around the tub connection
• Helps prevent water leaks at the tub-to-seal or tub-to-hose joint
• Restores proper fit when the original clamp is stretched, stripped, corroded, or missing
• Common symptoms: water at the base/front, loose seal or hose, visible clamp damage

• Disconnect power and turn off water before service
• Access the tub connection; remove the old clamp and inspect the seal/hose for wear
• Clean mating surfaces; seat the seal evenly, position the clamp, and tighten until snug without pinching the rubber
• Run a quick fill/drain test and check for leaks

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This is a replacement mounting screw used to secure panels and internal components on compatible Whirlpool appliances. It restores proper fastening where the original screw is missing, stripped, or damaged for a safe, snug fit. What it does:

• Secures panels, brackets, or small components to the appliance chassis
• Restores lost or damaged fasteners that cause rattling or looseness
• Helps maintain correct alignment of parts that rely on threaded fastening
• Prevents further wear by replacing stripped or corroded screws

• Use the matching screw length and thread engagement; do not force if resistance is encountered
• Tighten firmly but avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow manufacturer safety instructions before servicing
• Consider replacing all matching fasteners for uniform fit

This transport cover secures internal components during shipping and service to prevent movement and damage. It helps keep parts aligned and reduces noise caused by loose components while the appliance is being moved. What it does:

• Holds internal components in place during transport to prevent shifting or impact damage
• Reduces rattles and vibration caused by unsecured parts
• Protects delicate assemblies from knocks during delivery or handling
• Helps maintain alignment of components until the appliance is installed

• One transport cover

• Disconnect power and water before servicing the appliance
• Remove all shipping brackets and covers per the owner's manual before normal operation
• Use manufacturer-specified fasteners and torque; do not force or modify the part

This rivet secures panels, trim, or small components on compatible Whirlpool appliances to restore proper fit and reduce noise. It's a simple replacement for worn, loose, or missing fasteners so parts stay firmly in place. What it does:

• Holds appliance panels, brackets or trim pieces together for a secure fit
• Stops rattling or vibration caused by loose or missing fasteners
• Restores proper alignment of parts that rely on a permanent fastener
• Provides a durable, low-profile connection where a rivet was originally used

• Turn off and unplug the appliance before working on it to avoid shock or injury
• Remove the damaged rivet by drilling or cutting; install new rivet with the proper rivet tool or replacement method for the original rivet type
• Wear eye protection and follow basic hand-tool safety

This supporting clamp secures hose or component assemblies to help prevent movement and wear. It restores proper routing and restraint so hoses and wiring stay in place during normal operation. What it does:

• Holds hoses, tubes or small wiring bundles in position to reduce rubbing and chafing
• Prevents strain on connections that can cause leaks or intermittent electrical issues
• Keeps components aligned for reliable operation and quieter performance
• Useful when original clamp is cracked, broken, or no longer grips securely

• One supporting clamp

• Inspect mating surfaces and replace any damaged hoses or fasteners before installing
• Use appropriate hand tools; avoid over-tightening which can deform the clamp or hose
• Disconnect power and turn off water supply when working near electrical or plumbing connections

Rubber bumper. Color: Grey.