Kenmore Washer 110.47581602 (11047581602, 110 47581602) Parts

This motor-drive assembly powers the appliance's drive system to rotate the tub or drum so cycles run correctly. Replacing a worn or failed motor helps restore normal spinning and agitation for proper cleaning and drying. What it does:

• Converts electrical power into mechanical rotation to drive the tub/drum during operation
• Engages during spin/agitate cycles to move laundry and maintain cycle performance
• Helps maintain correct speed and torque required for load movement
• Failing unit can cause no spin, slow or inconsistent rotation, or unusual noises

• Disconnect power (unplug or turn off breaker) before starting any repair
• Handle unit and wiring harness carefully; verify connectors seat fully during reassembly
• Follow the appliance service manual for disassembly steps and torque/spec guidance
• If you detect burnt wiring or damaged mounting hardware, replace those items before operation

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This tub clamp secures a flexible seal or hose to the appliance's tub, maintaining a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop leaks and keep the tub joint stable during operation.

• Applies even clamping pressure around the tub connection
• Helps prevent water leaks at the tub-to-seal or tub-to-hose joint
• Restores proper fit when the original clamp is stretched, stripped, corroded, or missing
• Common symptoms: water at the base/front, loose seal or hose, visible clamp damage

• Disconnect power and turn off water before service
• Access the tub connection; remove the old clamp and inspect the seal/hose for wear
• Clean mating surfaces; seat the seal evenly, position the clamp, and tighten until snug without pinching the rubber
• Run a quick fill/drain test and check for leaks

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This is a replacement mounting screw used to secure panels and internal components on compatible Whirlpool appliances. It restores proper fastening where the original screw is missing, stripped, or damaged for a safe, snug fit. What it does:

• Secures panels, brackets, or small components to the appliance chassis
• Restores lost or damaged fasteners that cause rattling or looseness
• Helps maintain correct alignment of parts that rely on threaded fastening
• Prevents further wear by replacing stripped or corroded screws

• Use the matching screw length and thread engagement; do not force if resistance is encountered
• Tighten firmly but avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow manufacturer safety instructions before servicing
• Consider replacing all matching fasteners for uniform fit

This transport cover secures internal components during shipping and service to prevent movement and damage. It helps keep parts aligned and reduces noise caused by loose components while the appliance is being moved. What it does:

• Holds internal components in place during transport to prevent shifting or impact damage
• Reduces rattles and vibration caused by unsecured parts
• Protects delicate assemblies from knocks during delivery or handling
• Helps maintain alignment of components until the appliance is installed

• One transport cover

• Disconnect power and water before servicing the appliance
• Remove all shipping brackets and covers per the owner's manual before normal operation
• Use manufacturer-specified fasteners and torque; do not force or modify the part

This rivet secures panels, trim, or small components on compatible Whirlpool appliances to restore proper fit and reduce noise. It's a simple replacement for worn, loose, or missing fasteners so parts stay firmly in place. What it does:

• Holds appliance panels, brackets or trim pieces together for a secure fit
• Stops rattling or vibration caused by loose or missing fasteners
• Restores proper alignment of parts that rely on a permanent fastener
• Provides a durable, low-profile connection where a rivet was originally used

• Turn off and unplug the appliance before working on it to avoid shock or injury
• Remove the damaged rivet by drilling or cutting; install new rivet with the proper rivet tool or replacement method for the original rivet type
• Wear eye protection and follow basic hand-tool safety

This supporting clamp secures hose or component assemblies to help prevent movement and wear. It restores proper routing and restraint so hoses and wiring stay in place during normal operation. What it does:

• Holds hoses, tubes or small wiring bundles in position to reduce rubbing and chafing
• Prevents strain on connections that can cause leaks or intermittent electrical issues
• Keeps components aligned for reliable operation and quieter performance
• Useful when original clamp is cracked, broken, or no longer grips securely

• One supporting clamp

• Inspect mating surfaces and replace any damaged hoses or fasteners before installing
• Use appropriate hand tools; avoid over-tightening which can deform the clamp or hose
• Disconnect power and turn off water supply when working near electrical or plumbing connections

Rubber bumper. Color: Grey.

This replacement screw secures appliance panels and trim so components stay properly aligned and vibration is reduced. Use it to replace missing or damaged fasteners and restore a secure fit for safe operation. What it does:

• Fastens control panels, trim pieces, or access panels to the appliance frame
• Prevents panel movement, rattling, or gaps that can form from loose or missing screws
• Restores proper alignment after service or part replacement
• Helps maintain safe, stable operation by keeping panels secured

• Disconnect power (and gas if applicable) before servicing the appliance
• Use the correct driver bit and thread engagement; hand-start threads to avoid cross-threading
• Do not overtighten — snug until secure to avoid stripping or damaging panel threads
• Keep removed hardware organized to ensure correct locations during reassembly

The Vent Hose is an OEM part for Whirlpool washing machines. This vent hose allows air to circulate in and out of the washer, preventing pressure build-up and ensuring proper water drainage. It helps maintain the efficiency and effectiveness of the washing machine by facilitating the necessary airflow during the wash and spin cycles.

Common causes of a bad vent hose include wear and tear from regular use, blockages from lint or debris, and damage from mishandling or improper installation.

Symptoms of a bad vent hose include:

• Water not draining properly from the washer
• Unusual noises during the wash or spin cycles
• Leaks or water pooling around the washer
• Visible cracks, splits, or blockages in the hose

This OEM part is also compatible with some Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.