Kenmore Dryer 110.74964300 (11074964300, 110 74964300) Parts

This pipe plug seals an unused or service opening in a household appliance's plumbing to stop leaks and prevent debris entry. It restores a watertight closure so the appliance can operate safely and without water loss. What it does:

• Plugs open pipe or hose fittings to prevent water leaks
• Helps maintain proper water flow by sealing unused ports
• Keeps debris and contaminants out of the plumbing system
• Can stop intermittent drips originating from service openings

• One pipe plug

• Turn off water supply and power to the appliance before starting work
• Hand-start threads to avoid cross-threading; tighten only to OEM torque or finger-tight plus a quarter-turn if unspecified
• If the original used sealant or gasket, replace with the same type per OEM instructions

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it

This replacement burner funnel directs and contains the flame and heat from a gas cooktop burner for proper combustion and more consistent heating. It restores correct burner alignment and helps prevent uneven flames and cooking performance. What it does:

• Positions the burner head and ports to promote even flame pattern and reliable ignition
• Channels heat and combustion upward for stable cooking performance
• Helps contain spills and drips away from internal burner components
• Reduces sputtering or partial flames when damaged or misaligned

• One replacement burner funnel

• Turn off gas supply and electrical power to the appliance before beginning work
• Remove burner cap and burner head; lift old funnel out and set new funnel into place—no special tools typically required
• Do not force the part; ensure proper seating and alignment before reassembling burner components

This exhaust pipe directs heated air from the dryer drum to the household vent, restoring proper airflow for efficient drying and reduced lint buildup. It's a direct-fit replacement designed to match the OEM airflow path. What it does:

• Channels dryer exhaust from the appliance to the external vent to maintain proper airflow.
• Helps prevent lint accumulation in the cabinet by providing a sealed exhaust path.
• Can reduce long dry times and overheating caused by restricted or damaged venting.
• Addresses symptoms such as poor drying performance, hot dryer cabinet, or noticeable burning/overheating smells near the dryer vent area.

• One exhaust pipe.

• Disconnect power (and gas, if applicable) before starting work; the appliance is fully de-energized.
• Wear gloves to avoid sharp edges; remove old pipe and clean vent connections before installing the replacement.
• Secure with appropriate clamps or fasteners and ensure a continuous, unobstructed path to the exterior vent.
• After installation, run a short cycle to check for leaks.

This outer cabinet houses and protects the appliance's internal components, providing structural support and a finished exterior. Replacing a damaged cabinet restores stability and helps prevent exposure to wiring and internal parts. What it does:

• Provides the main structural enclosure for internal components and control assemblies
• Protects internal wiring, insulation, and mechanical parts from dust and damage
• Restores proper alignment of doors, panels, and access openings when dented or warped
• Helps maintain appliance appearance and resale value

• One outer cabinet

• Disconnect power (and water if applicable) before beginning any repairs
• Removing and installing the cabinet may require removing exterior panels, trim, and internal components first
• Have a second person available for lifting and aligning large cabinets to avoid damage or injury
• Keep hardware and grounding connections secure; follow OEM instructions for reassembly

Used for control panel.