Kenmore Washer 110.82427700 (11082427700, 110 82427700) Parts

Used from harness to top.

Restore dependable cycles with this replacement timer. It controls the sequence and duration of each step, sending power to the correct components at the right time so the machine advances smoothly from start to finish. What it does:

• Directs power to components to run each cycle segment in order
• Advances the cycle through preset intervals
• Helps resolve cycles that won't start or won't advance
• Addresses stopping mid-cycle or only running on certain settings
• Can help when the timer dial doesn't move or advances intermittently

• 1 timer

• Disconnect power before servicing; turn off water supply if applicable
• Access the control console; remove the knob/escutcheon if required and unmount the timer
• Transfer wires one at a time to the new timer or use a photo to match positions
• Reassemble and run a short test cycle to proper operation

This tub ring seal sits between the washer's outer tub and the tub ring. It creates a splash-resistant barrier at the top of the tub to keep wash water contained and help prevent leaks from the cabinet area.

• Seals the perimeter joint between the tub ring and outer tub
• Helps prevent water splashes from escaping during agitation and spin
• May help if you notice water around the lid/top of the cabinet
• Replace when the gasket is torn, brittle, or permanently compressed

• Unplug the washer and shut off the water supply before servicing
• Lift the top or remove the cabinet to access the tub ring (varies by model)
• Remove the tub ring; clean mating surfaces; seat the new seal evenly without twists
• Reassemble and run a short fill/agitate test to check for leaks

Color: Almond

Size: .20 Fl. Oz. (6 ml)

This protective cover for the washer's lid switch area guards the switch and wiring from water, detergent, and snagging inside the top panel, supporting reliable lid-closed detection and long-term safety interlock performance.

• Shields the lid switch and wiring from splashes, detergent, and debris under the top panel
• Helps prevent snagging or accidental contact with the switch mechanism
• Supports consistent lid-closed sensing by keeping the switch area protected and in position
• If the shield is damaged or missing, you may notice exposed switch/wiring or intermittent starting/spinning that improves when the lid is pressed

• Disconnect power before servicing; turn off water if moving the appliance
• Access the lid switch area by raising the top or opening the console per the service procedure
• Install the shield in the original orientation and secure with the existing fasteners
• After reassembly, verify the lid closes properly and the washer starts/spins as expected

Includes suspension pads.

Left hand side.

For mating terminal use WP94614.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

Replacement cycle timer that controls the appliance's timing and cycle advancement so your unit completes programmed operations. Installs where the original timer has failed, restoring proper sequencing of cycles. What it does:

• Controls cycle timing and advances the appliance through selected programs.
• Sends timed power to motors, valves, and other components to progress cycles.
• Common symptoms of a failing timer: appliance won't advance, stops mid-cycle, or refuses to start selected cycles.
• Replaces a worn or non-responsive original timer to restore normal cycle operation.

• Always disconnect power (unplug or flip breaker) before starting service.
• Handle the timer carefully to avoid damaging terminals; use proper tools and replacement grounding.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

Price Per Each

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This agitator cap covers the top of the washer agitator, restoring the finished appearance and helping keep the agitator post and fastener protected from lint and moisture. Ideal for replacing cracked, faded, or missing caps. What it does:

• Covers the agitator retaining bolt/fastener to reduce exposure and debris buildup
• Helps prevent fabric from snagging on an exposed agitator top
• Restores finished look to the agitator after damage or wear
• Useful when the original cap is cracked, broken, or discolored

• Disconnect power to the washer before servicing.
• This cap typically snaps into place or fits over the agitator post; some models require partial agitator removal.
• Use basic hand tools if agitator removal is necessary; avoid forcing plastic parts to prevent breakage.