Kenmore Washer 110.82992300 (11082992300, 110 82992300) Parts

Genuine Whirlpool part

Actuator

5.0 (2)

By: Whirlpool

Part Number: WP359807

This part fixes the following symptoms

Will not drain

Do-It-Yourself Stories from Customers like You The spin cycle on my washing machine was not working due to a faulty door/lid switch Joseph D. • Mechanicville , NY • February 17, 2015

I ordered a door/lid switch kit and an actuator and replaced them both. I probably didn't need the actuator, but it probably didn't hurt to replace it. The only issue I had was that the switch didn't seem to fit that well when installed on it's own, along with the actuator. So, I used the plastic shield which I had, along with the switch and actuator, as well as the old screws, as the screws that came with the kit were not long enough to accommodate the switch, actuator, and... Read more

Genuine Whirlpool part

Link

By: Whirlpool

Part Number: WP63466

Used for leveling mechanism. Includes a quantity of one. Order as needed

Genuine Whirlpool part

Tub Ring Gasket (Outer Tub Seal), Single

By: Whirlpool

Part Number: WP388201

This tub ring gasket seals the outer tub to help prevent water leaks and reduce vibration in top-load washers. It replaces a worn or damaged tub ring to restore a tighter seal and quieter operation. What it does:

Forms a watertight seal between the washer outer tub and surrounding components
Helps prevent water leaks that can lead to floor damage or appliance failure
Reduces tub movement and vibration caused by a loose or deteriorated ring
Common symptom: visible leaks around the tub edge or excess vibration/noise during wash cycles

What's included:

One tub ring gasket

Install notes:

For trained DIYers or professionals; disconnect power and water before starting
Inspect mating surfaces for damage or residue and clean before installing
Use appropriate tools and follow OEM diagram for correct seating and orientation

Genuine Whirlpool part

Actuator

5.0 (2)

By: Whirlpool

Part Number: 350733

This part fixes the following symptoms

Will not drain
Won't start

Do-It-Yourself Stories from Customers like You Would not go into agitate mode or drain Mike J. • Red Bank , NJ • April 29, 2018

I found the parts on your website and watched the video and it was fixed in no time. This parts site is always the one I go to first. I've done a number of projects and have never been disappointed. Read more

Genuine Whirlpool part

Swtch-Temp

5.0 (1)

By: Whirlpool

Part Number: W10858572

Do-It-Yourself Stories from Customers like You Model doesn’t have error code…no electronic displays. Lawrence F. • Norman , OK • August 01, 2023

Easy job. Had some issues connecting metal hoses to the plastic threads on the valve. Be cautious to not cross thread. Layout down towel to absorb water from the fill hoses and hoses out of the old valve. Took close to 40 min to get tools, complete job and put tools away. Read more

Genuine Whirlpool part

Lubricant

By: Whirlpool

Part Number: 285208

Use only in brake shoe assembly on roller & pin. Color: White/Grey.

Genuine Whirlpool part

Endcap

By: Whirlpool

Part Number: 285508

Genuine Whirlpool part

Reservoir

By: Whirlpool

Part Number: 285586

Genuine Whirlpool part

Hardware Kit

By: Whirlpool

Part Number: 285609

Genuine Whirlpool part

Reservoir

By: Whirlpool

Part Number: 285646

Genuine Whirlpool part

Strain Reliever

By: Whirlpool

Part Number: 285777

Genuine Whirlpool part

Reservoir

By: Whirlpool

Part Number: 3348814

Genuine Whirlpool part

Sensor

By: Whirlpool

Part Number: 3352282

Water inlet temperature sensor.

Genuine Whirlpool part

Water Inlet Valve, 3 Coil (Detergent Dispensing Models)

5.0 (1)

By: Whirlpool

Part Number: 3357901

Made by Whirlpool. This valve is commonly used on detergent dispensing washer models made by Whirlpool/Kenmore.

Do-It-Yourself Stories from Customers like You Faulty water inlet valve Gus F. • Rowland Heights , CA • February 04, 2016

Very simple. Removed 2 screws and lifted the control section. The from panel the was pulled out slightly. The water inlet valve was exposed and removed after disconnecting the hoses and 2 screws. I actually followed the direction on the Kenmore repair clinic on youtube!!!!! Read more