Kenmore Washer 110.85175600 (11085175600, 110 85175600) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W11033823
This wire retaining ring secures the door boot (bellow) to the front tub on front-load washers. It keeps the gasket seated to maintain a watertight seal, helping prevent leaks when the washer fills, agitates, and spins.
- Secures the door boot/gasket to the outer tub opening
- Maintains a watertight seal during wash and spin cycles
- Helps prevent the boot from slipping off the tub lip
- Common symptoms: water leaking at the front, a loose or detached boot, or a broken/missing ring
Includes: 1 wire retaining ring Install notes:
- Unplug the washer and shut off water; wear gloves and eye protection—the ring is under spring tension
- Release the outer boot clamp and fold the boot inward to access the inner ring
- Seat the boot evenly on the tub rim, then expand and fit the ring into its groove; verify it's fully seated all the way around
- Reassemble and run a quick test cycle to check for leaks
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21097
This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.
- Provides a protective wear surface between the hinge and cabinet/lid
- Reduces squeaks, creaks, and rattling when opening or closing the lid
- Helps maintain proper lid alignment and smooth movement
- Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid
What's included: 1 hinge pad Installation notes:
- Disconnect power to the washer before servicing
- Support the lid to relieve hinge tension and access the hinge area per your model
- Remove the worn pad and press the new pad fully into the hinge location
- Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two
Do-It-Yourself Stories from Customers like You
Cracked lid on a whirlpool cabrio washer Doug P. • Kansas City , MO • September 05, 2015
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.
- Supports and centers the spin basket on the tub centerpost/drive shaft
- Provides a low-friction bearing surface to reduce wear and noise
- Helps maintain basket alignment and stability during spin
- When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin
What's included: 1 centerpost bearing Install notes:
- Disconnect power and water supply before servicing; use proper PPE
- Access typically requires removing the agitator, inner basket, and related drive components
- Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
- Seat the bearing fully and verify smooth basket rotation before reassembly
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP367594
This front foot assembly is the adjustable leveling leg located at the front of the appliance. It supports and stabilizes the cabinet so it sits square and level, helping prevent rocking, vibration, and poor door alignment.
- Provides front support and height adjustment to level the unit
- Helps reduce rocking, vibration, and rattling during operation
- Replaces a worn, broken, missing, or stripped front foot
- Helps ensure doors or drawers align and close properly when leveled
What's included: 1 front foot assembly Install notes:
- Disconnect power and, if applicable, shut off water/gas before servicing
- Protect flooring; carefully tip or brace the appliance to access the front foot
- Unthread the old foot; thread in the new foot and adjust until level side-to-side and front-to-back
- Verify stability, then restore utilities and recheck for level
Do-It-Yourself Stories from Customers like You
Front foot was damaged Deborah L. • Mount Pleasant , WI • June 08, 2015
Replaced, it was a cinch!!!
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP72107
Color: Almond
Do-It-Yourself Stories from Customers like You
Broken meat drawer Jesse B. • Stow , MA • January 26, 2015
Replaced. Shippping was very fast. A good experience.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Whirlpool part
By: Whirlpool
Part Number: WP91770
Right hand side
Do-It-Yourself Stories from Customers like You
Lid was rusted bad Mike S. • San Lorenzo , CA • December 06, 2016
New parts easy fix
Read more
More
$19.79
- Compare At:
-
$21.36
- You Save:
-
$1.57
Genuine Whirlpool part
By: Whirlpool
Part Number: 350365
2 Port. Whirlpool and Kenmore washers.
Do-It-Yourself Stories from Customers like You
Water drain pump would not turn any more Robert T. • Belleville , IL • January 20, 2016
Ordered a replacement. Had to tip washer toward the back to provide access underneath to the
pump. Had some difficulty removing the two hose clamps. Pliers were not the best tool. Had to ensure the drive belt was properly engaged with the pulley of the pump.
Read more
More
$92.56
- Compare At:
-
$110.15
- You Save:
-
$17.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP354255
A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:
- Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
- Reduces vibration and rattling during operation
- Helps doors and panels sit properly when closed
- Simple, non-electrical part — no wiring or adjustment required
What's included:
Install notes:
- Inspect the mounting hole or surface; clean debris before installing
- Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
- Disconnect power to the appliance first and follow OEM instructions
- Remove old adhesive before installing the new bumper
Do-It-Yourself Stories from Customers like You
Broken fill valve John N. • Tumwater , WA • July 14, 2015
The video associated with the part was easy to understand. The actual repair was easy - maybe 10 minutes. But getting the top casing of the washer fitted back over the base was a huge pain. That took 8 tries to finally get it locked in just right. The washer is 20+ years old though.
The parts were all exactly correct and fit perfectly. Shipping time was excellent. Parts arrived in about 2 days with "standard" shipping.
The washer works great now. This is the second major repair I've done...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596797
Genuine Whirlpool part
By: Whirlpool
Part Number: 358277
Made by Whirlpool. Fits most Whirlpool, Kenmore, Estate and Roper belt driven washing machines.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Washing machine would not stop dripping into basket when finished washing Howard S. • Minneapolis , MN • April 25, 2021
Replaced washer water inlet valve.
Read more
More
$93.72
- Compare At:
-
$111.53
- You Save:
-
$17.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP94614
For mating terminal use [AP31136300].
More
$4.95
- Compare At:
-
$5.89
- You Save:
-
$0.94