Kenmore Dryer 110.86742701 (11086742701, 110 86742701) Parts

Restore smooth operation of your dryer's lint screen cover with this lint screen door spring. It provides the correct tension so the cover opens and closes properly and the lint screen seats securely for reliable lint collection.

• Applies spring tension to the lint screen door/cover hinge
• Helps the lint screen and cover stay properly positioned
• A worn or broken spring may cause the cover to feel loose, pop open, or not stay closed
• May make inserting or removing the lint screen difficult

• Disconnect power; for gas dryers, also shut off gas supply
• Access the lint screen door area per your model's service information
• Note the original spring orientation; transfer the new spring carefully using needle-nose pliers
• Check cover operation and lint screen seating before restoring power

This factory fastener secures appliance components and panels, helping keep assemblies properly aligned and tight. Replace worn, stripped, or missing hardware to eliminate looseness and vibration and maintain safe, reliable operation.

• Fastens brackets, panels, trim, and internal assemblies to the cabinet/frame
• Helps maintain alignment of doors, consoles, or covers
• Restores a tight fit to reduce rattling, vibration, or shifting
• Common symptoms: missing screw, stripped head/threads, loose panel or handle, recurring vibration/noise

• Disconnect power (and shut off gas/water if applicable) before servicing
• Match thread and length to the original fastener for proper fit
• Start threading by hand to avoid cross-threading; use the correct driver
• Do not overtighten into plastic or thin sheet metal

The lid switch lever connects the washer's lid hinge to the lid switch, signaling when the lid is closed so the cycle can run. A damaged lever can prevent the safety interlock from closing, leading to no-start or spin issues. What it does:

• Transfers lid movement at the hinge to the lid switch actuator
• A closed lid so the washer can operate
• Common symptoms of a failed lever: washer won't start; won't spin; cycle pauses because the lid-closed signal isn't detected

• 1 lid switch lever

• Disconnect power before servicing
• Lift or open the top to access the hinge/switch area; locate the lever near the lid switch
• Remove the old lever and install the new one in the same orientation; free movement
• Close the lid by hand and the switch clicks before reassembly and testing

This Heater Box Bracket secures the dryer's heater housing to the cabinet, keeping the heating assembly firmly mounted and aligned. Replace a bent, cracked, or missing bracket to restore stable support and reduce vibration around the heater area.

• Anchors the heater housing/box to the cabinet frame
• Maintains proper alignment and clearance for the heating element assembly
• Helps prevent rattling or rubbing noises from a loose heater housing
• A damaged bracket may leave the heater housing loose, cause vibration, or contribute to intermittent heating issues

• Disconnect power; if gas, shut off gas supply and allow the unit to cool completely
• Access the heater housing; note bracket orientation and reuse existing fasteners
• Support the heater housing and keep wiring clear while removing/installing the bracket
• After installation, verify the housing sits square and clear of the drum and wiring before restoring power

For mating terminal use WP94614.

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test

For mating terminal use [AP31136300].

This replacement screw secures appliance components as designed by the manufacturer. Installing a new fastener restores a tight fit when the original is missing, stripped, or corroded, helping prevent vibration and misalignment during use.

• Fastens brackets, panels, or assemblies in the specified locations
• Replaces missing, stripped, or rusted hardware
• Helps maintain proper alignment and reduce vibration/noise
• Common signs you need this part: loose components, rattling, or a screw that won't tighten

• Disconnect power and turn off water supply before servicing
• Match the screw to its original location; length and thread engagement
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse any original washers or spacers that were installed with the screw

This out exhaust pipe directs a dryer's exhaust airflow from the appliance to the home vent, helping remove moisture and lint from the dryer cabinet. Durable replacement for worn or damaged exhaust tubing. What it does:

• Channels hot, moist air from the dryer to the external vent to prevent moisture buildup
• Helps maintain proper airflow for efficient drying and reduces lint accumulation inside the cabinet
• Replaces cracked, crushed, or disconnected exhaust connections that cause poor venting or air leaks
• Works as a direct-fit plumbing piece when original exhaust piping is damaged

• One out exhaust pipe

• Disconnect power to the appliance before installing; for gas dryers, turn off gas supply and pilot per manufacturer instructions
• Ensure the pipe fits securely to the dryer outlet and the wall vent; use manufacturer-recommended clamps or fasteners
• Inspect and clean the vent path and lint screen while replacing the pipe to ensure safe airflow

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Flat metal washer that helps secure fasteners and evenly distribute load on mounting points. Replacing a worn or corroded washer restores proper fastener grip, reduces vibration, and stops loose or rattling parts. What it does:

• Provides a smooth bearing surface for nuts and bolts, preventing pull-through and damage
• Distributes clamping force to protect mounting surfaces and maintain alignment
• Helps reduce vibration and noise from loose or worn fasteners
• Replace when bent, corroded, cracked, or missing to restore secure mounting

• Always disconnect power to the appliance before beginning repairs; follow all safety precautions
• Use the correct size fastener and torque to avoid over-tightening or crushing the washer
• Inspect surrounding hardware and replace any damaged or corroded bolts, nuts, or brackets

This hose kit replaces worn or damaged appliance hoses to restore proper water flow and prevent leaks. It's a direct-fit replacement for compatible Whirlpool systems and helps stop visible leaks and restore normal fill/drain operation. What it does

• Replaces cracked, split or leaking hoses to stop water loss and reduce risk of appliance damage
• Restores reliable water flow for filling and draining functions
• Helps eliminate poor draining, intermittent filling, or water pooling near the appliance
• Works with existing clamps and connections when installed correctly

• Disconnect power and shut off the water supply before starting any repair
• Inspect connection fittings and replace clamps if worn; ensure a snug, leak-free fit
• Route hoses without kinks and secure to avoid chafing or strain
• After installation, run a short cycle and check all connections for leaks

This exhaust cover plate protects and finishes the dryer's exhaust outlet, helping direct airflow and keeping the vent opening sealed from debris. It provides a clean, durable surface where the exhaust connects to the dryer cabinet. What it does:

• Covers and seals the dryer exhaust opening to prevent dust and lint buildup around the vent
• Helps direct exhaust airflow into the duct for proper ventilation
• Restores a finished appearance to the exhaust area after repair or replacement
• Can reduce drafts and discourage pests entering through the vent opening

• Disconnect power to the appliance before starting any work.
• Use basic hand tools; handle edges carefully to avoid cuts.
• Verify proper alignment with the exhaust opening and secure with the original screws or hardware.
• Inspect the exhaust duct and surrounding seals for wear.

This motor mounting bracket secures the appliance motor to the cabinet, keeping the motor steady for reliable operation and reduced vibration. It's a direct-fit replacement designed to restore proper motor alignment and support. What it does:

• Holds the motor in the correct position to prevent movement during operation
• Reduces motor vibration and noise caused by loose or damaged mounting
• Helps maintain proper belt alignment and drivetrain performance
• Supports safe, stable motor operation under normal load conditions

• One motor mounting bracket

• Disconnect power to the appliance before beginning any repair
• Basic mechanical skills and common hand tools are usually required
• Inspect mounting hardware and adjacent components; replace any worn fasteners

This terminal cover protects and conceals the appliance's electrical wire terminals for safer handling and cleaner internal appearance. It helps reduce accidental contact with live connections and keeps wiring organized. What it does:

• Covers exposed wire terminals to help prevent accidental contact and shorting
• Keeps wiring routed and held in place for improved serviceability
• Protects terminals from dust and debris that can affect connections
• Supports safer access during diagnostics and repairs

• One terminal cover, as shown

• Disconnect power to the appliance before attempting any service
• Remove outer panels as needed to access the terminal area; use manufacturer service guide for panel removal steps
• Align cover over the terminal block and secure per factory mounting points; do not force or modify
• If terminals or wiring appear damaged or corroded, replace or repair those components before reinstalling the cover

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components