Kenmore Dryer 110.87580200 (11087580200, 110 87580200) Parts

Genuine Whirlpool part

Clamp

By: Whirlpool

Part Number: 341029

$8.45

Compare At:: $10.14
You Save:: $1.69

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

Genuine Whirlpool part

Wire

By: Whirlpool

Part Number: 687133

$23.52

Compare At:: $25.87
You Save:: $2.35

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

Genuine Whirlpool part

Washer

By: Whirlpool

Part Number: WP298877

$14.41

Compare At:: $14.44
You Save:: $0.03

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

Genuine Whirlpool part

Clip

By: Whirlpool

Part Number: WP342267

$7.95

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

Best Seller

Genuine Whirlpool part

Toe Panel Clip Kit

4.7 (11)

By: Whirlpool

Part Number: 279638

This kit secures the lower toe/kick panel to the front of the appliance, keeping the panel tight and properly aligned. Replacing worn or missing clips restores a secure fit and makes access for service straightforward.

Holds the toe/kick panel in place at the base of the cabinet
Helps prevent panel rattling, gaps, or a loose/hinging lower panel
Common fix when the lower panel won't stay secured after service
Durable metal clip design for repeated panel removal and reattachment

What's included: Toe panel clip kit Install notes:

Unplug appliance before servicing; wear gloves to avoid sharp edges
Support the toe panel while releasing old clips to prevent bending
Install clips in the cabinet slots first, then engage the panel into the clips
Verify the panel is fully seated on both sides before restoring power

Do-It-Yourself Stories from Customers like You Door would not stay closed. Mark B. • Greenfield , WI • January 05, 2020

Purchased the above kit to repair the door hardware. Also had to purchase door hinges to replace one I found broken after disassembling the dryer front. Parts arrived as shown in the online pictures, and arrived within 4-5 business days. Read more

Genuine Whirlpool part

High Limit Thermostat

4.0 (1)

By: Whirlpool

Part Number: 279048

L205-40. Dryer

This part fixes the following symptoms

No heat or not enough heat

Do-It-Yourself Stories from Customers like You No heat Robert F. • Fort Waayne , IN • March 31, 2016

Found that when I "jumped" the hi limit thermostat the gas valve operated. So just went ahead and R/R the Hi limit thermostat, thermo-fuse, and the cycling thermostat. No problems. Read more

Genuine Whirlpool part

Timer Knob

4.9 (10)

By: Whirlpool

Part Number: WP688865

Color: Chrome. Measures about 2 inches in diameter.

Do-It-Yourself Stories from Customers like You Broken timer knob Anthony F. • Coral Springs , FL • March 26, 2016

Removed old knob. Replaced with new one. A "pull - push" operation. PERFECT FIT!! Read more

Genuine Whirlpool part

Seal, Blower Shaft

4.8 (12)

By: Whirlpool

Part Number: WP3394196

Do-It-Yourself Stories from Customers like You The motor on our clothes dryer was doing a "self protection" thermal or overload shutdown and there was a strong odor in the tub Jim S. • Fallon , NV • November 27, 2015

It took two repair attempts to fix the dryer. At first, I noticed that the rear felt seal was completely worn out, so I thought that extra friction between the tub and the rear panel might be causing the motor to have to work too hard and overheat. I ordered a new seal from appliancepartspros.com, and installed it according to their instructional video, but it did not correct the problem. Then I decided that the motor must be going bad, so I watched the on-line video on how to remove the... Read more

Genuine Whirlpool part

Dryer Gas Valve And Burner Assembly

By: Whirlpool

Part Number: 279894

Complete burner assembly with gas valve, coils and igniter. Setup for natural gas.

Genuine Whirlpool part

Handle

5.0 (1)

By: Whirlpool

Part Number: WP3977746

Do-It-Yourself Stories from Customers like You The lever to turn on dryer was broken the handle was broken and the latch was broken David R. • Jemison , AL • February 09, 2015

I opened the top of the dryer (after watching the video on your website) and replaced the lever on the switch. Removed two screws near the lint filter, used a putty knife to release fasteners under the top and raised the top. Held it in place with a short piece of board then removed the two screws holding in the switch and lever. Replaced the broken lever with the new one and put it all back together. The handle was a little more difficult as it took a lot more prying with a screwdriver to... Read more