Kenmore Washer 110.91264800 (11091264800, 110 91264800) Parts

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

This drain hose clamp secures the hose connection to keep water where it belongs during the drain cycle. A tight, reliable clamp helps prevent leaks and hose pull-off from vibration or pressure changes. What it does:

• Secures the drain hose to a pump outlet or drain port to maintain a watertight seal
• Helps prevent the hose from slipping off during operation
• Reduces leaks at the hose connection point
• Common symptoms of a bad clamp: water leaking at the drain hose joint, a loose/detached hose, or a visibly rusted/broken clamp

• 1 clamp

• Disconnect power and turn off the water supply; place a towel to catch residual water
• Access the hose connection, remove the old clamp, and inspect the hose end and fitting; replace the hose if cracked or swollen
• Position the new clamp correctly over the hose and behind the fitting bead; tighten/seat evenly without overtightening
• Reassemble and run a brief drain test to check for leaks

Price Per Each

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This agitator cap covers the top of the washer agitator, restoring the finished appearance and helping keep the agitator post and fastener protected from lint and moisture. Ideal for replacing cracked, faded, or missing caps. What it does:

• Covers the agitator retaining bolt/fastener to reduce exposure and debris buildup
• Helps prevent fabric from snagging on an exposed agitator top
• Restores finished look to the agitator after damage or wear
• Useful when the original cap is cracked, broken, or discolored

• Disconnect power to the washer before servicing.
• This cap typically snaps into place or fits over the agitator post; some models require partial agitator removal.
• Use basic hand tools if agitator removal is necessary; avoid forcing plastic parts to prevent breakage.

A replacement 3/8-16 nut that secures fasteners and assemblies on compatible Whirlpool appliances. Restores proper fastening so panels, brackets and components stay tight and aligned during normal operation. What it does:

• Fastens and secures bolts, studs or threaded shafts in appliance assemblies.
• Prevents loose connections that can cause rattling, vibration or misalignment.
• Used where a 3/8-16 threaded nut is required for structural or mounting applications.
• Replaces missing, stripped or corroded nuts to restore reliable mechanical connection.

• Disconnect power and follow all appliance safety procedures before servicing.
• Inspect mating threads and remove debris; replace if threads are damaged.
• Thread onto bolt or stud by hand first, then snug with the correct wrench; avoid overtightening.
• Follow the appliance manufacturer's torque and assembly instructions.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

Spring-style hose clamp that secures flexible appliance hoses to fittings, helping keep connections tight to reduce leaks and maintain proper water flow. Use it to replace a worn or damaged clamp and restore a reliable hose seal. What it does:

• Compresses around a flexible hose to lock it onto barbs or fittings
• Helps prevent drips, leaks, and water pooling at hose connections
• Keeps hoses from slipping off during appliance operation
• Useful when a clamp is corroded, stretched, or no longer holds tension

• Disconnect power and shut off water to the appliance before starting any repairs
• Use pliers to compress the clamp for removal and installation; keep hands and face clear when releasing tension
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

Bottle with brush. Color: Harvest Gold. It's 0.6 fluid ounces.

Motor mount to gear case.

This agitate gear washer is a small flat washer used with the washer's agitate gear to ensure proper spacing and smooth engagement. It helps maintain correct gear alignment so the agitator can move laundry effectively. What it does:

• Provides a stable spacer between the agitate gear and mating components to prevent excess play
• Helps maintain correct gear alignment for consistent agitator movement
• Reduces metal-on-metal contact that can cause noise or premature wear
• Commonly replaced when the agitator feels loose, makes grinding noise, or causes uneven agitation

• High-level replacement: remove agitator/gear per service manual to access washer; reinstall in original orientation
• Use manufacturer torque/settings for reassembly; do not overtighten
• Inspect adjacent gear and splines for wear; replace any damaged components
• Disconnect power and follow safety procedures before servicing the washer