Kenmore Washer 110.91512210 (11091512210, 110 91512210) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10086010
This motor retainer secures the motor to its mounting point, keeping the assembly tight and aligned. Replace a worn or broken retainer to cut vibration and noise and to protect nearby seals, wiring, and components. What it does:
- Holds the motor firmly in place within the assembly
- Maintains alignment for smooth, quiet operation
- Supports sealing surfaces and connections; on water-bearing assemblies, help prevent leaks
- Replace if you notice a loose or rattling motor, new vibration/noise, or signs of movement or leakage at the motor
What's included:
- Includes 1 motor retainer.
Install notes:
- Disconnect power; turn off water supply.
- Access the motor area and support the motor before removing the old retainer.
- Inspect mating parts and seals; replace any damaged components.
- Fully seat the motor and install the new retainer securely; test for abnormal noise or leaks.
Do-It-Yourself Stories from Customers like You
Motor drive & mounts Mark H. • Winnemucca , NV • October 10, 2024
A former repair man deleted the grommets from the motor mount plate, the spring fastening the motor to the bracket broke the screw inside the motor and once the motor fell out of place the drive to the the transmission was broken.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
This anti-rattle screw secures panels or brackets to prevent vibration noise in compatible appliances. Replacing a missing or stripped screw restores a tight fit and helps keep the cabinet and assemblies stable and quiet.
- Secures brackets, ducts, or panels to reduce buzzing and rattling during operation
- Replaces a lost, worn, or damaged anti-rattle fastener
- Helps maintain proper alignment and prevents vibration-related wear
- Typical symptoms include persistent rattling, a loose panel, or hardware found inside the cabinet
What's included: One anti-rattle screw Installation notes:
- Disconnect power before servicing; for gas appliances, shut off the gas supply
- Access the mounting point and remove the loose or damaged screw
- Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening
- Repair or replace the bracket/clip before reassembly
Do-It-Yourself Stories from Customers like You
No spin on spin cycle Richard S. • Beaumont , CA • August 28, 2015
Replaced clutch assembly which was a little tricky, but very doable. Just make sure to take your time. I do have to say that I am very impressed with AppliancePartsPro customer service when the replacement part also failed. A new clutch assembly was at my door step a few days later. I now has a working washer again. Thanks Again Appliance Parts Pro.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP357213
Push-in.
Do-It-Yourself Stories from Customers like You
Washer would fill with water and then do nothing else Richard C. • Torrance , CA • December 05, 2015
I saw videos on it possibly being the lid switch. I used 2 lead wires to bypass the lid switch, which indicated it was indeed the lid switch that was faulty.
I ordered the lid switch, which came in 2 days. I installed it in less than 7 minutes.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3356311
This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.
Do-It-Yourself Stories from Customers like You
Water would continue to fill the tub. David J. • Loveland , CO • September 22, 2023
Replaced the water inlet valve.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP389387
This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.
- Transfers oscillating motion from the transmission to the agitator
- Provides the splined interface that engages the agitator/coupler
- Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
- Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator
What's included: 1 agitator drive shaft Install notes:
- Disconnect power and water; use proper PPE
- Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
- Keep gears, spacers, and clips in order; reassemble in the original orientation
- Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn
Do-It-Yourself Stories from Customers like You
Agitator was not turning Edward M. • Glen Allen , VA • March 10, 2019
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time.
Read more
More
$116.95
- Compare At:
-
$141.04
- You Save:
-
$24.09
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62889
Used for lid switch.
Do-It-Yourself Stories from Customers like You
Washer was "dead" with a partially washed load and would not do anything Jimmy M. • Hopewell , VA • September 19, 2014
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!)
Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts...
Read more
More
$16.77
- Compare At:
-
$19.79
- You Save:
-
$3.02
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.
- Supports and centers the spin basket on the tub centerpost/drive shaft
- Provides a low-friction bearing surface to reduce wear and noise
- Helps maintain basket alignment and stability during spin
- When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin
What's included: 1 centerpost bearing Install notes:
- Disconnect power and water supply before servicing; use proper PPE
- Access typically requires removing the agitator, inner basket, and related drive components
- Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
- Seat the bearing fully and verify smooth basket rotation before reassembly
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3355454
This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.
- Applies tension to prevent rattling and buzzing during use
- Helps keep the mounted piece properly seated and aligned
- Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
- Simple, drop-in replacement where the original clip is used
What's included: 1 anti-rattle clip Install notes:
- Disconnect power to the appliance before servicing
- Note the original clip's orientation; transfer the new clip the same way
- Use needle-nose pliers for placement; avoid over-bending the clip
- The component is secure and clears adjacent parts before reassembly
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: 285666
Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138
Do-It-Yourself Stories from Customers like You
I was replacing the lid switch but decided to install a new vacuum break and drain hose while i was at it Dianne Z. • Manchester , CT • May 27, 2016
Just took off the old vacuum break and put the new one on. It was very easy because the site had a video showing how and I watched it first.
Read more
More
$44.95
- Compare At:
-
$53.49
- You Save:
-
$8.54
Genuine Whirlpool part
By: Whirlpool
Part Number: 285702
Size: 21 inches long. Clamp included.
Do-It-Yourself Stories from Customers like You
Drain hose too short and home depot fix leaked Sara B. • Liberty Hill , TX • August 21, 2015
Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly.
Now we're washing again and no leaks!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP54583
Right hand side. For screws use WPW10119828.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$19.50
- Compare At:
-
$23.20
- You Save:
-
$3.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3359586
This tub ring seal sits between the washer's outer tub and the tub ring. It creates a splash-resistant barrier at the top of the tub to keep wash water contained and help prevent leaks from the cabinet area.
- Seals the perimeter joint between the tub ring and outer tub
- Helps prevent water splashes from escaping during agitation and spin
- May help if you notice water around the lid/top of the cabinet
- Replace when the gasket is torn, brittle, or permanently compressed
What's included: 1 tub ring seal Install notes:
- Unplug the washer and shut off the water supply before servicing
- Lift the top or remove the cabinet to access the tub ring (varies by model)
- Remove the tub ring; clean mating surfaces; seat the new seal evenly without twists
- Reassemble and run a short fill/agitate test to check for leaks
More
$45.95
- Compare At:
-
$55.14
- You Save:
-
$9.19