Kenmore Washer 110.91566400 (11091566400, 110 91566400) Parts

Size: 10-24 x 3/8 inch.

This drain hose clamp secures the hose connection to keep water where it belongs during the drain cycle. A tight, reliable clamp helps prevent leaks and hose pull-off from vibration or pressure changes. What it does:

• Secures the drain hose to a pump outlet or drain port to maintain a watertight seal
• Helps prevent the hose from slipping off during operation
• Reduces leaks at the hose connection point
• Common symptoms of a bad clamp: water leaking at the drain hose joint, a loose/detached hose, or a visibly rusted/broken clamp

• 1 clamp

• Disconnect power and turn off the water supply; place a towel to catch residual water
• Access the hose connection, remove the old clamp, and inspect the hose end and fitting; replace the hose if cracked or swollen
• Position the new clamp correctly over the hose and behind the fitting bead; tighten/seat evenly without overtightening
• Reassemble and run a brief drain test to check for leaks

Price Per Each

This pressure switch is a factory-replacement control that senses air/pressure changes and helps the dryer run correct cycles and safety functions. It restores proper pressure detection so the dryer can heat and cycle as intended. What it does:

• Detects air/vacuum pressure changes to signal the dryer control for cycle and safety operations
• Helps ensure normal heating and timed cycles by allowing the control to confirm airflow/vent conditions
• Common symptom linkage: dryer won't heat, won't start, runs too long, or displays pressure/airflow-related fault codes
• Works with the dryer's vent/air sensing system

• One pressure switch

• Disconnect power before servicing to avoid shock or injury
• Inspect hoses and venting for blockages; replace damaged vacuum/air hose when installing this switch
• Handle connectors and terminals gently; ensure secure electrical connections and correct routing of pressure hose

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This mechanical Mallory/Variflex timer controls cycle selection and timing for the appliance, restoring reliable cycle advancement and user control. Replaces a worn or faulty timer to help the appliance run through selected cycles correctly. What it does:

• Rotates and switches internal contacts to select cycle stages and timing
• Advances the appliance through wash/dry/cook cycles (depending on model)
• Common symptom: appliance won't start or won't advance through cycles
• Common symptom: selector knob moves but cycle does not change
• Restores timed control when original timer stops responding

• Disconnect power to the appliance before starting any work
• Access typically requires removing the control panel or console; keep track of screws and fasteners
• Label or photograph wire locations before disconnecting to ensure correct reconnection
• Test function after installation

For end of drain hose.

Spring-style hose clamp that secures flexible appliance hoses to fittings, helping keep connections tight to reduce leaks and maintain proper water flow. Use it to replace a worn or damaged clamp and restore a reliable hose seal. What it does:

• Compresses around a flexible hose to lock it onto barbs or fittings
• Helps prevent drips, leaks, and water pooling at hose connections
• Keeps hoses from slipping off during appliance operation
• Useful when a clamp is corroded, stretched, or no longer holds tension

• Disconnect power and shut off water to the appliance before starting any repairs
• Use pliers to compress the clamp for removal and installation; keep hands and face clear when releasing tension
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

Bottle with brush. Color: Harvest Gold. It's 0.6 fluid ounces.

Color: White

Note: The manufacturer no longer includes the motor shield WP3946532 mentioned in the video. If needed, order it separately.

The Direct Drive Washer Motor is an OEM part for Whirlpool washing machines This motor drives the agitation, spinning, and draining processes during the laundry cycles, ensuring clothes come out clean and well spun. 

Causes of a bad Direct Drive Washer Motor can range from wear and tear over time, overheating due to overloading or obstructed movement, and electrical failures like short circuits or blown capacitors. 

Symptoms of a failing Direct Drive Washer Motor include:

• The washing machine not agitating or spinning correctly
• A noticeable decline in the washer's performance
• Unusual noises, such as humming or buzzing, indicating the motor is struggling

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Hose used from mixing valve to sensor housing.

This balance ring mounts on the top of the washer's spin basket. Its sealed, liquid-filled chamber shifts weight to counterbalance uneven loads so the tub spins smoothly, reducing vibration, noise, and stress on other components. What it does:

• Uses internal fluid to counterbalance heavy or uneven loads during spin
• Helps minimize vibration, shaking, and thumping noises
• Reduces washer movement or "walking" during spin
• Common failure symptoms: excessive vibration/noise, frequent out-of-balance loads, or visible cracks/leaks at the ring

• 1 balance ring assembly

• Disconnect power and water; wear gloves and use proper safety precautions
• Access the ring by removing the cabinet/top and inner basket (procedure varies by model)
• Remove the old ring; seat the new ring evenly on the basket rim—do not puncture the sealed chamber
• Reassemble, level the washer, and run a test spin to ensure smooth operation