Kenmore Washer 110.92060100 (11092060100, 110 92060100) Parts

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

Size: 10-16 x 5/8 inch.

Almond. Size: 13 oz. can. Acrylic appliance paint.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

Used from harness to top.

Right hand side. For screws use WPW10119828.

Restore dependable cycles with this replacement timer. It controls the sequence and duration of each step, sending power to the correct components at the right time so the machine advances smoothly from start to finish. What it does:

• Directs power to components to run each cycle segment in order
• Advances the cycle through preset intervals
• Helps resolve cycles that won't start or won't advance
• Addresses stopping mid-cycle or only running on certain settings
• Can help when the timer dial doesn't move or advances intermittently

• 1 timer

• Disconnect power before servicing; turn off water supply if applicable
• Access the control console; remove the knob/escutcheon if required and unmount the timer
• Transfer wires one at a time to the new timer or use a photo to match positions
• Reassemble and run a short test cycle to proper operation

Color: Almond

Size: .20 Fl. Oz. (6 ml)

A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:

• Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
• Reduces vibration and rattling during operation
• Helps doors and panels sit properly when closed
• Simple, non-electrical part — no wiring or adjustment required

• One replacement bumper

• Inspect the mounting hole or surface; clean debris before installing
• Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
• Disconnect power to the appliance first and follow OEM instructions
• Remove old adhesive before installing the new bumper

This protective cover for the washer's lid switch area guards the switch and wiring from water, detergent, and snagging inside the top panel, supporting reliable lid-closed detection and long-term safety interlock performance.

• Shields the lid switch and wiring from splashes, detergent, and debris under the top panel
• Helps prevent snagging or accidental contact with the switch mechanism
• Supports consistent lid-closed sensing by keeping the switch area protected and in position
• If the shield is damaged or missing, you may notice exposed switch/wiring or intermittent starting/spinning that improves when the lid is pressed

• Disconnect power before servicing; turn off water if moving the appliance
• Access the lid switch area by raising the top or opening the console per the service procedure
• Install the shield in the original orientation and secure with the existing fasteners
• After reassembly, verify the lid closes properly and the washer starts/spins as expected

Includes suspension pads.

Left hand side.

For mating terminal use WP94614.