Kenmore Washer 110.92274100 (11092274100, 110 92274100) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP357213
Push-in.
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP389387
This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.
- Transfers oscillating motion from the transmission to the agitator
- Provides the splined interface that engages the agitator/coupler
- Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
- Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator
What's included: 1 agitator drive shaft Install notes:
- Disconnect power and water; use proper PPE
- Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
- Keep gears, spacers, and clips in order; reassemble in the original orientation
- Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn
Do-It-Yourself Stories from Customers like You
Agitator was not turning Edward M. • Glen Allen , VA • March 10, 2019
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time.
Read more
More
$116.95
- Compare At:
-
$141.04
- You Save:
-
$24.09
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62889
Used for lid switch.
Do-It-Yourself Stories from Customers like You
Washer was "dead" with a partially washed load and would not do anything Jimmy M. • Hopewell , VA • September 19, 2014
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!)
Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts...
Read more
More
$16.77
- Compare At:
-
$19.79
- You Save:
-
$3.02
Genuine Whirlpool part
By: Whirlpool
Part Number: WP389386
This is the central wash-action component in select top-load washers. Replacing a worn or damaged agitator restores proper agitation so clothes circulate through water and detergent for consistent cleaning performance. What it does:
- Converts drive motion into the back-and-forth action that moves laundry
- Circulates clothes to improve soil removal and reduce tangling
- Replaces cracked, stripped, or loose agitators that cause weak or no agitation
- Common symptoms include poor cleaning, clothes not moving during wash, or an agitator that wobbles or spins freely by hand
What's included:
Install notes:
- Disconnect power and turn off water supply before servicing
- Remove the fabric softener dispenser and inner cap to access the center bolt
- Remove the bolt, lift off the old agitator, seat the new agitator on the splined shaft, and secure the bolt
- Reinstall the cap/dispenser; reuse original hardware as applicable and check for a secure fit before testing
Do-It-Yourself Stories from Customers like You
Top agitator would not spin Daniel C. • Woodbine , MD • January 14, 2017
I have a 25 year old Kenmore washer that works well and didn't want to get a new washer as they don't make them like they used to. Upon removing the top cap of the agitator and doing an inspection, the agitator dogs were completely broken into pieces. Due to age we decided to replace the lower and upper agitator along with the agitator auger dogs repair kit. All new parts and works fine. On inspection of old parts, we probably could have gotten away with just a $5 repair for the plastic...
Read more
More
$89.34
- Compare At:
-
$107.94
- You Save:
-
$18.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21097
This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.
- Provides a protective wear surface between the hinge and cabinet/lid
- Reduces squeaks, creaks, and rattling when opening or closing the lid
- Helps maintain proper lid alignment and smooth movement
- Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid
What's included: 1 hinge pad Installation notes:
- Disconnect power to the washer before servicing
- Support the lid to relieve hinge tension and access the hinge area per your model
- Remove the worn pad and press the new pad fully into the hinge location
- Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two
Do-It-Yourself Stories from Customers like You
Cracked lid on a whirlpool cabrio washer Doug P. • Kansas City , MO • September 05, 2015
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3355454
This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.
- Applies tension to prevent rattling and buzzing during use
- Helps keep the mounted piece properly seated and aligned
- Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
- Simple, drop-in replacement where the original clip is used
What's included: 1 anti-rattle clip Install notes:
- Disconnect power to the appliance before servicing
- Note the original clip's orientation; transfer the new clip the same way
- Use needle-nose pliers for placement; avoid over-bending the clip
- The component is secure and clears adjacent parts before reassembly
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3356467
This water level pressure switch senses the tub's fill level through an air hose and signals the washer to start or stop filling and advance the cycle. Replacing a faulty switch restores proper fill levels and reliable cycle timing.
- Monitors water level via an internal pressure diaphragm connected to the tub air hose
- Opens/closes contacts to control the inlet valve and inform the timer/control
- Common symptoms: washer overfills or keeps filling, won't fill, incorrect/erratic water levels
- Cycle may stall at fill or rinse when the switch doesn't detect the proper level
What's included: 1 water level switch Install notes:
- Disconnect power and turn off water before servicing
- Access the console; transfer wires to the new switch one at a time to maintain correct positions
- Inspect and firmly seat the pressure hose; ensure the hose and tub air dome are clear and the hose isn't cracked or kinked
- After installation, run a test fill to verify proper shutoff at the selected level
Do-It-Yourself Stories from Customers like You
Wash machine once in a while would stop running Daniel B. • Leesburg , FL • May 13, 2016
I found that turning the water level switch back and forth would activate the machine So I replaced the water level switch and the plastic hose that connected to it.
I purchased a clamp in the purchase, but it was the wrong size! There wasn't a clamp used in the original set up, so I installed the switch and hose without it! It was the video instructions and having the correct parts that made that made this a easy repair!
Thank You
Read more
More
$101.95
- Compare At:
-
$121.32
- You Save:
-
$19.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546455
This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.
- Supports and centers the spin basket on the tub centerpost/drive shaft
- Provides a low-friction bearing surface to reduce wear and noise
- Helps maintain basket alignment and stability during spin
- When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin
What's included: 1 centerpost bearing Install notes:
- Disconnect power and water supply before servicing; use proper PPE
- Access typically requires removing the agitator, inner basket, and related drive components
- Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
- Seat the bearing fully and verify smooth basket rotation before reassembly
More
$18.26
- Compare At:
-
$21.73
- You Save:
-
$3.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP661597
This timer controls the length and sequence of your appliance's operating cycles. Replacing a worn or stuck timer restores proper advancement so the machine starts, runs through each stage, and shuts off when it should.
- Advances the cycle automatically through each stage
- Sends power to components at the correct time
- Helps ensure the unit starts and stops on schedule
- Helps when the cycle won't advance, stops mid-cycle, runs too long/never shuts off, or only works on one setting
What's included: 1 timer Install notes:
- Disconnect power before servicing
- Access the timer behind the control panel/console
- Transfer wires one at a time from the old timer to the new, matching positions
- Secure the timer with mounting screws; align the shaft with the dial/knob as applicable and test operation
Do-It-Yourself Stories from Customers like You
The machine would not move through its cycles Wayne M. • Fairbanks , AK • September 17, 2014
Replaced the timer
Read more
More
$182.95
- Compare At:
-
$217.71
- You Save:
-
$34.76
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP54583
Right hand side. For screws use WPW10119828.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$19.50
- Compare At:
-
$23.20
- You Save:
-
$3.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.93
- You Save:
-
$1.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP72107
Color: Almond
Do-It-Yourself Stories from Customers like You
Broken meat drawer Jesse B. • Stow , MA • January 26, 2015
Replaced. Shippping was very fast. A good experience.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Whirlpool part
By: Whirlpool
Part Number: WP285195
$59.65
- Compare At:
-
$71.58
- You Save:
-
$11.93