Kenmore Washer Dryer Combo 110.92962100 (11092962100, 110 92962100) Parts

This small retaining clip secures a lever mechanism inside the appliance, keeping the linkage aligned so the control operates smoothly. Replacing a bent or missing clip helps restore proper engagement and prevents the mechanism from popping loose. What it does:

• Locks the lever mechanism to its bracket or shaft
• Maintains alignment of moving linkage for consistent operation
• Replaces missing, bent, or broken retainer
• Common symptoms: loose/wobbly lever, mechanism slips out, control doesn't engage reliably

• Clip only

• Disconnect power before servicing
• Access the mechanism per your model's service information and relieve any spring/linkage tension
• Note the original orientation; use needle-nose pliers to seat the new clip fully in the groove
• Test the mechanism for smooth operation before reassembly

This transition duct directs dryer exhaust from the appliance to the home vent, helping maintain proper airflow and reduce vent leaks. It keeps exhaust moving out of the cabinet for safer, more efficient drying. What it does:

• Channels dryer exhaust from the appliance outlet to the household vent
• Helps prevent lint and moisture from escaping into the cabinet or laundry area
• Can reduce long dry times and overheating caused by restricted or damaged ducting
• Commonly replaced when venting is crushed, torn, or leaking

• Disconnect power (and gas, if applicable) and move the appliance away from the wall before replacing the duct
• Inspect adjoining vent hoses and seals; replace or reseal as needed for a tight fit
• Use appropriate clamps or connectors and follow local venting codes for safe exhaust routing

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This aerosol spray paint restores the graphite finish on appliance surfaces for quick, low-effort cosmetic touch-ups. Use it to cover small chips, scratches and scuffs so the exterior looks uniform again. What it does:

• Matches graphite appliance finishes for spot repairs and touch-ups
• Covers visible chips, scratches and minor surface scuffs
• Restores a uniform appearance on painted metal appliance surfaces
• Helps protect exposed metal from surface corrosion after repair

• Clean and dry the surface; remove grease, dirt and loose paint before spraying
• Shake can well and test spray on a scrap piece or inconspicuous area first
• Apply in light, even coats from a recommended distance; allow coats to dry between passes
• Use in a well-ventilated area, keep away from heat/open flames, and follow all safety and disposal instructions on the can

This spring damper assembly cushions and stabilizes the appliance drum during spin cycles, reducing vibration and helping maintain smooth, balanced operation. It restores proper drum support and motion control for safer, quieter performance. What it does:

• Absorbs and dampens drum movement to reduce vibration and banging during spin
• Helps keep the drum properly aligned to prevent wobbling or rubbing
• Can resolve symptoms such as loud thumping, excessive vibration, or uneven spinning
• Works as the suspension support between the drum and cabinet to improve cycle stability

• Disconnect power (and water, if applicable) before beginning any repair
• Handle springs and mounting points carefully—springs are under tension and can snap if released improperly
• Installation may require partial disassembly of the cabinet or drum; follow the OEM service manual or instructions

This is a 10-16 x 1/2 inch appliance screw used to secure panels and components on compatible Whirlpool laundry and kitchen appliances. It restores a secure fit when a fastener is missing or stripped. What it does

• Fastens trim, panels, brackets or small components to the appliance chassis
• Replaces a lost or damaged factory screw to stop rattling or loose parts
• Matches OEM thread and length for proper engagement and holding strength
• Helps maintain alignment and safe operation of the attached part

• Use the correct screwdriver or nutdriver to avoid stripping the head
• Tighten until snug—do not overtighten to prevent damage to threads or sheet metal
• Disconnect power and follow the appliance manufacturer's safety instructions before servicing

This right-side door hinge rebuilds a worn or damaged pivot point so the appliance door opens, closes and seals properly. It restores door alignment and prevents sagging that can cause gaps and cooling loss. What it does

• Replaces the right-side door pivot to restore correct door swing and alignment
• Reduces door sag and helps maintain an even seal to improve temperature retention
• Stops rubbing, scraping or binding that can occur with a worn hinge
• Works with the existing hinge housing and fasteners when used as a direct replacement

• One right-side door hinge (single hinge)

• Install with power to the appliance off and interior removed as needed for safe access
• Support the door during replacement to prevent dropping or additional damage
• Use the OEM fasteners and torque to manufacturer recommendations; inspect surrounding parts for wear

This factory hinge supports and pivots the appliance door so it opens smoothly and closes square to the cabinet. Replacing a worn or bent hinge restores proper alignment, sealing, and overall door feel.

• Provides the pivot point and carries the door's weight for smooth operation
• Helps keep the door aligned so it closes flush and seals correctly
• Direct replacement for a bent, seized, or excessively worn hinge
• Typical symptoms: door sags or rubs, squeaks/clicks at the hinge, won't close flush or stay closed

• Disconnect power to the appliance before servicing and allow hot surfaces to cool
• Support the door during removal/installation to prevent strain on the remaining hinge
• Transfer any screws, plates, or bushings from the old hinge as shown in your model's diagram
• After installation, check door alignment and gasket contact; adjust per the service instructions if needed

This is a replacement side trim screw that secures the refrigerator side trim/finish panel, restoring a snug fit and finished appearance. Designed to match the original factory fit and finish on compatible Whirlpool units. What it does:

• Fastens the side trim/finish panel so the exterior trim sits flush and secure
• Helps stop rattling, shifting, or gaps caused by loose or missing trim screws
• Matches factory color and head style to keep a consistent exterior look
• Small hardware piece used in multiple trim/assembly locations

• One side trim screw (black)

• Use the matching screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can crack trim or strip threads
• Turn power off and remove any nearby panels if needed for safe access
• Replace all to ensure even fit

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

This replacement clamp secures flexible hoses and lines to prevent leaks and keep connections tight. It restores a secure seal so appliances move water or air without escaping at the joint. What it does:

• Secures inlet, drain or water lines to fittings and housings
• Helps stop leaks from loose or worn hose connections
• Keeps hoses from slipping off during operation or vibration
• Commonly replaced when clamps are corroded, broken, or no longer hold tension

• Inspect hose and fitting for damage before installing the new clamp
• Position clamp over the hose barb and tighten evenly until snug; avoid over-tightening
• Use appropriate tools (pliers or clamp driver) and follow appliance safety procedures
• Disconnect power and shut off water supply when working on water lines

For end of drain hose.

This replacement lid stop bumper cushions and stabilizes the washer lid, helping prevent hard slams and reducing wear on the lid and cabinet. Restores smoother, quieter lid operation on compatible top-load washers. What it does:

• Acts as a soft stop that cushions the lid when closing to reduce noise and impact.
• Keeps the lid aligned and prevents metal-on-metal contact that can cause scratches or damage.
• Helps the lid sit flush and avoid rattling during wash cycles.
• Suitable as a direct replacement for worn, cracked, or missing lid bumpers.

• One white lid stop bumper as shown.

• Disconnect power before inspecting or servicing the washer.
• Typically installs by pressing into the mounting hole on the lid or cabinet;
• Replace when the bumper is torn, compressed, or missing to restore proper cushioning.

This front drum bulkhead is the stationary front panel that supports the dryer drum and seals the drum opening to maintain proper airflow and drum alignment for reliable drying performance. What it does:

• Provides a mounting surface and seal for the front of the dryer drum to help maintain correct drum alignment
• Directs airflow from the drum into the exhaust plenum for consistent drying
• Reduces rubbing and wear on the drum edge and front roller or glide surfaces
• Can help stop visible grinding, scraping or excess vibration when worn or cracked

• One front drum bulkhead

• Turn off power and disconnect the dryer before beginning service
• Handle plastic parts carefully to avoid cracking; check surrounding seals and rollers during replacement
• Some models require removal of the front panel and drum for access; keep fasteners organized for reassembly

This drum baffle replaces a worn or damaged lifter inside the dryer drum to help clothes tumble evenly and prevent items from bunching. Restores proper tumbling and reduces rubbing/snags caused by broken or missing lifters. What it does:

• Lifts and separates clothes as the drum turns to promote even drying
• Helps prevent garments from tangling or bunching in the drum
• Reduces fabric rubbing and potential snags caused by damaged lifters
• Commonly replaced when the original is cracked, loose, or missing

• One drum baffle

• Disconnect power before starting repairs
• Removal of the dryer drum or front panel is typically required; follow model-specific service instructions
• Use appropriate hand tools and keep track of mounting screws/clips for reassembly
• Inspect drum, mounting studs, and fasteners; replace any stripped or damaged hardware for a secure fit