Kenmore Washer Dryer Combo 110.99576200 (11099576200, 110 99576200) Parts

This OEM replacement part is a washer tub assembly. The tub is the cylindrical piece that is found inside the washer where the clothes are put. Damage to the tub can cause it to not rotate properly. If the tub is making excessive noise during the wash cycle and appears to be misaligned, damaged, or broken, it might be time for a replacement. Start by removing the front panel of the washing machine. Then proceed to remove the top and back panels. After gaining access to the interior of the machine, disconnect any hoses attached to the drum and take note of where they go. Using a screwdriver, remove the screws that hold the drum to the machine. Lift the tub out, and replace it with the new one. Be sure to re-attach everything properly. Secure the front back and top panels of the washer.This genuine replacement part is compatible with Bosch, Gaggenau, and Thermador, washing machines.

Motor mount to gear case.

This drum assembly replaces a worn or damaged dryer drum to restore proper tumbling and prevent fabric damage. Durable stamped steel construction helps maintain smooth rotation and even drying for front-load dryers. What it does:

• Replaces a dented, cracked, or bent drum that can catch or tear clothing
• Restores smooth tumbling to eliminate scraping, rubbing, or loud metal-on-metal noises
• Helps maintain proper airflow and even drying when the original drum is damaged
• Works with existing rollers, seals, and support components when those parts are in good condition

• Disconnect power (and gas, if applicable) before beginning any repair
• Handle the drum carefully—edges can be sharp; use gloves and eye protection
• Some disassembly of the dryer cabinet and removal of front bulkhead may be required
• Inspect and replace worn rollers, glides, or seals as needed for best results; test operation after reassembly

Size: 6 - 20 x 1 1/16 inch.

This bulkhead is the front interior panel that supports the drum and helps direct dryer airflow for efficient tumbling and exhaust. It restores proper drum alignment and airflow when the original panel is worn or damaged. What it does:

• Provides a stable mounting surface for the drum and front bearing/glide assembly
• Helps channel air from the drum to the exhaust path for consistent drying
• Prevents drum wobble and rubbing that can cause noise or fabric wear
• Reduces air leaks and hot spots that can extend dry times or trigger heat issues

• One bulkhead panel

• Disconnect power and venting before beginning any repair
• Removing the front panel and drum is typically required to access and replace the bulkhead
• Inspect drum seals, rollers, and bearings while the dryer is open; replace any worn components
• Use appropriate tools and follow OEM instructions.

This hinge bracket secures a refrigerator door hinge to the cabinet, restoring proper door alignment and support so the door seals and closes reliably. Designed to replace a worn, bent, or broken hinge mounting bracket. What it does:

• Provides a stable mounting point for the door hinge assembly to prevent sagging or drooping
• Restores correct door alignment to improve sealing and reduce cold air loss
• Stops excess movement or rattling at the hinge area
• Helps eliminate door-binding or uneven gaps that keep the door from closing fully

• Unplug the appliance and remove food/items from the door before starting
• Support the door while removing/installing the bracket to avoid damage or injury
• Reuse or replace fasteners as required; tighten securely but avoid over-torquing
• After installation, check door alignment and gasket seal; make minor adjustments as needed

This retaining clip secures appliance panels and small components to keep parts aligned and prevent rattling. Durable and compact, it restores proper fit where clips have broken or worked loose. What it does

• Holds panels, trim pieces or small assemblies in place to prevent vibration and misalignment
• Stops rattling or rubbing caused by loose or missing fasteners
• Keeps wiring harnesses or small components seated
• Works as a direct replacement for a worn or broken clip shown in OEM parts diagrams

• Disconnect power before attempting any repair to avoid shock or injury
• Access may require removing trim or panels; keep fasteners organized for reassembly
• Install by pressing clip into the matching slot until it snaps; verify the secured part is seated
• If clip is damaged or the mating slot is deformed, replace both clip and any damaged mount for reliable fit