Kenmore Washer Dryer Combo 110.99576200 (11099576200, 110 99576200) Parts

This lint duct seal cushions and seals the dryer lint duct to help direct airflow through the exhaust path and reduce leaks. Replacing a worn seal improves drying efficiency and helps prevent lint escape into the cabinet. What it does:

• Seals the lint duct connection to maintain proper exhaust airflow and reduce air leakage
• Helps keep lint contained in the duct pathway to reduce buildup inside the cabinet
• Can reduce unusual airflow-related noise or vibration caused by a deteriorated seal
• Supports consistent drying performance when the original seal is cracked, torn, or compressed

• Disconnect power to the dryer before beginning any work; follow all electrical safety precautions
• Access may require removing the dryer front or top panel depending on model—refer to your model's service instructions
• Remove the old seal and clean mating surfaces before installing the new seal for a secure fit
• After installation, inspect venting and run a short test cycle to ensure proper airflow and fit

This motor shield protects and secures the appliance motor assembly, helping block debris and contact with nearby components so the motor can run reliably. It's a direct-fit replacement for a damaged or missing motor shield. What it does

• Shields the motor from debris and foreign objects that can cause rubbing or obstruction.
• Helps secure and position the motor within the cabinet to maintain proper alignment.
• Reduces risk of contact between the motor and other parts that can cause noise or wear.
• Replacing a cracked or missing shield can prevent recurring motor issues and reduce abnormal sounds.

• Disconnect power to the appliance before beginning any repair.
• Use basic hand tools; avoid forcing fasteners or damaging adjacent components.
• Wear gloves to protect against sharp edges on the shield or mounting area.

Use with motor 357282.

Almond

This blower housing directs dryer airflow from the drum to the exhaust for proper ventilation and consistent drying performance. It replaces a cracked or damaged housing to restore airflow and reduce noise. What it does:

• Channels heated air from the drum to the exhaust vent to maintain drying efficiency
• Helps support the blower wheel and keeps the wheel aligned for smooth operation
• Commonly replaced for reduced airflow, longer dry times, or unusual noise from the rear of the dryer
• Can prevent overheating caused by restricted or leaking airflow

• Disconnect power (and gas supply if applicable) before beginning repair
• Handle edges carefully; wear gloves to avoid cuts and protect the blower wheel
• Reassemble panels and test dryer on a short cycle to confirm airflow and quiet operation

This exhaust vent extension provides extra duct length to move dryer or hood exhaust farther from the appliance, improving airflow routing and helping reduce backpressure and lint buildup in short-vent installations. What it does:

• Extends the length of an existing exhaust duct to reach a distant vent outlet
• Helps restore proper ventilation when original ducting is too short
• Reduces restricted airflow that can cause longer dry times or excess lint accumulation
• Works as an inline rigid/semirigid extension piece for exhaust systems

• Disconnect power (and gas for gas dryers) before accessing or modifying exhaust connections
• Remove lint and debris from ducting before installing the extension to ensure clear airflow
• Securely fasten with appropriate clamps or foil tape and maintain a smooth, unobstructed path

This connector is an insulated electrical harness terminal that joins appliance wiring to restore a secure electrical connection and help prevent intermittent power or arcing. It's a direct-replacement style used on select Whirlpool appliances. What it does:

• Provides a secure, insulated connection between two wires or a wire and a component terminal.
• Helps stop intermittent power, flickering, or loss of function caused by loose or damaged terminals.
• Reduces risk of arcing and overheating at a compromised connection point.
• Matches OEM fit/shape to maintain proper routing and strain relief where applicable.

• Turn off and unplug the appliance (or shut off breaker) before inspecting or replacing electrical parts.
• Inspect surrounding wiring and terminals for heat or corrosion; replace damaged wiring as needed.
• Use proper crimping or terminal tools and secure strain relief; verify firm, no-play connections before restoring power.

This OEM replacement part is a washer tub assembly. The tub is the cylindrical piece that is found inside the washer where the clothes are put. Damage to the tub can cause it to not rotate properly. If the tub is making excessive noise during the wash cycle and appears to be misaligned, damaged, or broken, it might be time for a replacement. Start by removing the front panel of the washing machine. Then proceed to remove the top and back panels. After gaining access to the interior of the machine, disconnect any hoses attached to the drum and take note of where they go. Using a screwdriver, remove the screws that hold the drum to the machine. Lift the tub out, and replace it with the new one. Be sure to re-attach everything properly. Secure the front back and top panels of the washer.This genuine replacement part is compatible with Bosch, Gaggenau, and Thermador, washing machines.

This front panel clip secures the appliance's front/console panel to the cabinet, keeping the panel aligned and preventing vibration or rattling. It's a small but essential fastener for a tight, stable fit. What it does:

• Holds the front or control panel in position on the appliance cabinet
• Prevents panel movement, rattling, or gaps that can affect alignment
• Helps maintain a flush fit between the panel and surrounding trim
• Commonly needed when clips are cracked, broken, or missing

• Disconnect power (and gas if applicable) before beginning any service
• Access usually requires removal of trim or control console; use appropriate screwdrivers
• Replace any additional damaged clips to ensure even panel support

Color: White. Size: 1 qt. can. Acrylic appliance paint.