Kenmore Freezer 253.28712808 (25328712808, 253 28712808) Parts

This cabinet breaker kit forms the insulating trim around the appliance opening. It provides a proper surface for the door or lid gasket to seal against and helps minimize condensation along the edge for clean, reliable performance.

• Creates the thermal break and finished edge around the cabinet opening
• Supports correct seating of the door/lid gasket for a consistent seal
• Helps reduce sweating or moisture at the perimeter
• Replaces cracked, warped, or missing breaker trim components

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the door/lid if required for access and retain all fasteners
• Carefully remove old breaker components and clean the mounting surfaces
• Install the new breaker and corners, align evenly, avoid overtightening, and verify the gasket seals all around

A small replacement mounting clip that secures interior trim or panels on select refrigerators, helping restore a snug fit and reduce loose, rattling parts. Fits where worn or broken clips allow trim to shift. What it does:

• Holds trim, panels or small components in place to prevent rattling and movement.
• Restores proper alignment of affected panels so edges sit flush and look finished.
• Simple mechanical fastening — replaces brittle or broken clips that no longer grip.
• Helps reduce noise caused by loose interior parts during normal operation.

• Always unplug the appliance or switch off power at the breaker before servicing.
• Remove the affected trim or panel per manufacturer instructions to access the clip location.
• Press the clip into the mating slot or post until it seats securely; use a small tool if needed to avoid fingernail or surface damage.
• Inspect surrounding mounting surfaces for cracks or wear; damaged supports may require additional replacement parts.

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water delivery and ice production when the valve is faulty or worn. What it does:

• Opens and shuts to allow water into the ice maker and dispenser when activated
• Common symptom: no water to dispenser or ice maker
• Common symptom: reduced or intermittent water flow from dispenser
• Common symptom: ice maker not filling or producing smaller/soft ice
• Can cause visible leaks at the valve or connections when failing

• One water inlet valve assembly

• Turn off water supply and unplug appliance before beginning work
• Relieve any pressure in the water line and have towels handy for minor spills
• Verify inlet/outlet hose orientation and tighten all fittings to OEM torque; use replacement gaskets if supplied

This mounting bracket secures internal components and panels to restore proper alignment and reduce vibration. It provides a direct replacement for worn or damaged support hardware so assemblies stay firmly in place. What it does:

• Secures appliance panels or internal components to the cabinet or frame
• Keeps parts aligned to prevent rattling, vibration, or movement during operation
• Restores proper fit where a bent, broken, or missing bracket causes loose assemblies
• Helps maintain safe, stable operation by holding parts in their designed position

• One mounting bracket

• Designed to replace the factory bracket in the same mounting location; verify fit before installation
• Use appropriate fasteners and torque to avoid striping or damage to mounting points
• Disconnect power and empty unit if needed before accessing internal areas

This left-side tiltout end cap replaces the damaged or worn plastic end piece that secures and guides a fridge/freezer tilt-out or dairy bin. Restores a secure fit and smooth opening for the tilt-out assembly. What it does:

• Replaces the left end cap on a tilt-out/dairy bin assembly
• Helps keep the drawer aligned and held in place during use
• Reduces rattling or catching when opening and closing the tilt-out
• Matches OEM fit and mounting points for direct replacement

• One left tiltout end cap

• Remove contents and the tilt-out bin before attempting replacement
• Installation typically requires basic hand tools and gentle prying to disengage clips
• Inspect mating clips and housing; replace or repair any broken tabs before reinstalling

This replacement screw fastens appliance panels and components to restore a secure fit and reduce vibration or rattling. Use when original hardware is missing, loose, or stripped to keep parts aligned and operating quietly. What it does:

• Secures panels, brackets, and trim to prevent movement and rattling.
• Replaces missing or damaged hardware that can cause loose or misaligned parts.
• Helps maintain proper component alignment for reliable operation.
• Small but essential fastener for safe, stable assembly.

• Disconnect power before servicing any electrical appliance.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until snug—do not overtighten, which can strip threads or crack panels.
• Keep removed hardware organized to ensure correct reinstallation.

A replacement interior light shield that protects the refrigerator light and helps diffuse illumination for even lighting throughout the fresh-food compartment. Restores proper light coverage after a cracked or missing lens. What it does:

• Covers and protects the fridge light bulb from spills, debris and accidental contact
• Diffuses light for more even interior illumination
• Prevents direct glare from the bulb to make contents easier to see
• Commonly replaced when cracked, broken, yellowed, or missing

• Remove power to the appliance before starting—unplug or switch off the breaker
• Typically snaps or screws into place; handle gently to avoid cracking the new lens
• Use a soft cloth and mild cleaner; avoid abrasive pads or harsh solvents
• Inspect the housing and replace hardware as needed

This diffuser directs and disperses airflow inside the refrigerator compartment to help maintain even temperatures and prevent cold spots. It's a small plastic vent piece that routes air coming from the evaporator into the cabinet. What it does:

• Guides and spreads cold air from the evaporator fan to improve cabinet airflow
• Helps reduce localized hot or cold spots near vents
• Prevents direct air blasts that can cause uneven cooling of stored items
• Should be replaced if cracked, warped, or broken to restore proper airflow

• Disconnect power to the appliance before starting any service
• Typically snaps or slides into the vent opening; may require a flat screwdriver to release retaining tabs
• Inspect surrounding vent housing for damage and replace as needed
• Refer to your model's service guide for specific removal/replacement steps