Kenmore Refrigerator 253.54703400 (25354703400, 253 54703400) Parts

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

A replacement fixed round blade that restores the appliance's original blade function and helps reduce vibration, noise or uneven performance caused by a worn or damaged blade. Use this OEM component for a proper fit and reliable operation. What it does

• Replaces a worn, bent or damaged fixed round blade to restore intended blade performance.
• Restores balance and smooth operation to the rotating assembly.
• Can reduce noise, wobble or uneven operation associated with a damaged blade.
• Matches OEM fit and function to help ensure correct alignment.

• Disconnect power to the appliance before beginning any work.
• Handle blade edges carefully; wear cut-resistant gloves if available.
• Remove and install per the appliance service manual or OEM instructions.

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This replacement mounting screw fastens panels and components in compatible Frigidaire appliances to restore secure assembly and reduce rattling or loose parts. Simple fastener sized for the original factory location. What it does:

• Secures panels, brackets, or trim to keep parts aligned and stable
• Prevents vibration and noise caused by loose fittings
• Restores proper attachment after repair or disassembly
• Matches the OEM thread and length for a correct fit when specified

• Use the correct screw hole and do not force; cross-threading can damage components
• Tighten to a snug fit—do not overtighten to avoid stripping threads or cracking plastic
• Power tools can be used with care; slow speed and proper bit help prevent slippage
• Turn off power and disconnect the appliance before accessing internal parts

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.

The Ice Maker Cooling Duct is an OEM part for Frigidaire refrigerators. It directs cold air flow to the ice maker.

Causes of failure can be blockages or damage to the duct over time that impact efficient air flow.

Symptoms of a bad cooling duct include:

• Inconsistently shaped or formed ice cubes
• Slow or reduced ice production
• The ice maker failing to dispense ice properly
• Higher than normal interior refrigerator temperatures near the ice maker

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This ice container deflector attaches to the ice bucket assembly and guides cubes toward the dispenser chute. Replacing a cracked or missing deflector restores proper ice flow and helps keep ice from spilling inside the freezer during dispensing.

• Directs ice from the bucket into the dispenser chute/crusher path
• Helps maintain consistent dispensing and minimizes stray ice inside the freezer
• Replace if cracked, warped, or missing
• Symptoms include erratic dispensing, ice spilling or jamming, or a visibly damaged/missing guide on the ice bin

• Disconnect power before servicing; remove the ice bucket
• Position the new deflector in the original location; reuse existing screws/clips if applicable
• Ensure the curved face points toward the dispenser chute
• Reinstall the ice bucket, restore power, and test ice dispense

Access door provides a finished cover for the appliance's service opening, protecting internal components from dust and damage while keeping the unit looking tidy and allowing access for maintenance and repairs. What it does:

• Covers the service or access opening and protects wiring, valves, and other internal parts.
• Allows access to controls, connections, or components for inspection and repair without removing major panels.
• Helps prevent debris, pets, or fingers from contacting internal parts.
• Replace a missing, cracked, or damaged access door to restore appearance and reduce exposure of internal components.

• Always disconnect power (and gas for gas appliances) before removing panels or working on the appliance.
• Handle the door and surrounding edges carefully to avoid cuts; keep original fasteners and reuse if undamaged.
• Align tabs/clips and secure with manufacturer screws; do not overtighten.

Color: Black

This temperature control knob replaces a worn or broken fridge temperature dial so you can set the refrigerator temperature accurately. It restores a solid grip and clear pointer for reliable, easy adjustments. What it does:

• Fits onto the temperature control shaft to select colder or warmer settings
• Provides a clear pointer for precise temperature selection
• Replaces cracked, stripped, or missing knobs that make adjustments difficult
• Helps eliminate loose or slipping knob operation

• One temperature control knob

• Push-fit installation onto the control shaft; no special tools typically required
• Ensure power is off and remove food before working in the appliance for safety
• Inspect the control shaft for damage; replace the control if the shaft is stripped