Kenmore Dishwasher 363.1404193 (3631404193, 363 1404193) Parts

Genuine Ge part

Spring

By: Ge

Part Number: WD1X1354

Genuine Ge part

Terminal (12-Pack)

5.0 (2)

By: Ge

Part Number: WD1X1434D

Includes 12 terminals.

Do-It-Yourself Stories from Customers like You Terminal receptacle was fried Phillip M. • Indianapolis , IN • May 12, 2015

I had to replace the 3 terminals and try to put them in the new terminal receptacle. I replaced the lid switch because I broke the old one trying to diagnose the problem. I found the helpful video on this site after I had already started. Read more

Genuine Ge part

Solen Bracket

5.0 (1)

By: Ge

Part Number: WD1X1439

Do-It-Yourself Stories from Customers like You The drain solenoid on dishwasher leaked and rusted where wouldn't work Webster M. • Memphis , TN • September 19, 2014

Ordered complete solenoid kit, valve seal, and sol mounting screws. Watched repair video and it works great. Read more

Genuine Ge part

Cap

By: Ge

Part Number: WD1X5405

Genuine Ge part

Dishwasher Timer

By: Ge

Part Number: WD21X748

This replacement timer is a genuine OEM part for a dishwasher. The timer works to regulate a dishwasher's cycles by controlling how long power is supplied to the internal components. This allows the dishwasher to have multiple wash modes and shut on or off automatically once set by the operator. The timer assembly can be located behind the kickplate in the door or at the top of the control panel. Dishwasher timers are often misdiagnosed as the problem in a faulty appliance, so be sure to test the timer before immediately replacing it. Using a multimeter, test the timer for a range of roughly 2,000 to 3,500 ohms. If the part does not give a reading within this range, it should be replaced. Disconnect the two attached wires and mark them so that they can be properly reattached during reassembly. Needle-nosed pliers are recommended for this job, as they can provide a more delicate touch than just yanking out the wires. This replacement timer is compatible with Kohler washers and comes sourced from its original manufacturer. This part does not include any additional hardware so be sure not to lose any of the screws removed during disassembly.

Genuine Ge part

Hub

By: Ge

Part Number: WD22X121

Genuine Ge part

Pop Up

By: Ge

Part Number: WD22X124

Genuine Ge part

Support Assembly

4.5 (2)

By: Ge

Part Number: WD22X126

Do-It-Yourself Stories from Customers like You Dishes were not getting clean spray arm was not fully extending up and water hardly came out of spray arm you could open door half way and watch inside Don F. • Bellevue , NE • April 05, 2015

Replaced spray arm assembly, it's a different style than what was in the dishwasher but it's an easier style to work with. I also ordered support assembly and did not need it,spray arm assembly was all I needed. Read more

Genuine Ge part

Kick Toe

By: Ge

Part Number: WD27X10171

Genuine Ge part

Dishwasher Door Panel Insert, White/Almond

5.0 (1)

By: Ge

Part Number: WD27X497

Reversible panel - white on one side, almond on the other.

Do-It-Yourself Stories from Customers like You We needed a white door insert for our dishwasher John S. • Dagsboro , DE • April 24, 2014

We called your company and you found it. We had called several others including GE with no success. Read more

Genuine Ge part

Rack, Lower

By: Ge

Part Number: WD28X268

Genuine Ge part

Pump Drain Valve Arm Kit

By: Ge

Part Number: WD35X192

This kit fits both D style and T style shafts.

Genuine Ge part

Timer Lever Spring

By: Ge

Part Number: WD3X749

Genuine Ge part

Washer

5.0 (1)

By: Ge

Part Number: WD3X766

Do-It-Yourself Stories from Customers like You Our ge dishwasher model gsd580p49ba was not fully cleaning dishes after washing. we kept finding grainy food particles and debris deposited all over the dishes Mary H. • Boonsboro , MD • February 07, 2020

We removed the spray arm from the Spray Arm Hub and Support Assembly (GE part WD22X126) and discovered that the Check Valve (GE part WD1X5488), which prevents dirty water from flowing back into the tub, was missing completely. Replacement was very easy - the soft rubber valve pushes into position from the inside of the Support Assembly. We also found that the Plastic Thrust Washer (GE part WD3X766) inside the center of the Spray Arm Hub had eroded considerably, so we replaced that as well. Read more