Kenmore Dishwasher 587.15373100A (58715373100A, 587 15373100A) Parts

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This sump assembly is the dishwasher's lower-tub pump housing that circulates and drains wash water. Replacing a cracked or clogged sump restores proper drain and circulation, helping stop leaks and restore normal wash performance. What it does:

• Houses the pump and channels wash water for circulation and draining.
• Restores proper drainage when the dishwasher won't drain or holds water in the tub.
• Stops leaks that develop from cracked or damaged sump housings at the base.
• Reduces pump noise or grinding caused by debris, cracks, or a failing housing.

• Disconnect electrical power and water supply before beginning any service.
• Access the sump from the dishwasher's lower front (remove the lower rack and toe-kick/access panel as needed).
• Take care with wiring and hose clamps; transfer any motors, seals, or fittings only if required and follow manufacturer torque/placement.
• After installation, run a short cycle and inspect for proper drain/circulation and any leaks before reassembling trim.

Restore your dishwasher's brains with this control assembly. It manages cycle selection and timing so the machine responds to commands, starts reliably, and completes wash cycles without random beeps, stalls, or unresponsive controls.

• Coordinates cycle logic and component operation
• Interprets button/touch inputs from the console
• Drives status indicators or display on applicable models
• Typical symptoms: controls unresponsive, won't start, lights flicker or beep erratically, cycle won't advance

• Disconnect power at the breaker before servicing
• Use anti-static precautions; handle the board by its edges and avoid touching contacts
• Label/photograph wiring; move connectors one at a time and fully seat any ribbon cables/locks
• Reuse existing mounting hardware; ensure correct orientation and secure harness routing before reassembly

This adjustable leveling leg threads into the appliance base to support and stabilize the unit. Replacing a worn or missing foot restores proper leveling for smoother operation, better door alignment, and reduced vibration.

• Provides height adjustment to level the appliance on uneven floors
• Helps keep the unit stable to minimize rocking and rattling
• Improves door alignment and closure when the cabinet is properly leveled
• Replaces a cracked, stripped, or missing leg

• Disconnect power; if your appliance has a water line, turn off the supply and carefully move the unit to access the leg.
• Support the appliance to relieve weight; unthread the damaged leg and start the new leg by hand to avoid cross-threading.
• Adjust height by turning the foot; use a level to ensure the cabinet is plumb and stable.
• Tighten carefully and recheck stability after the appliance is set back in place.

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

Replacement screw that secures trim, panels and internal components to restore proper fit and reduce rattling. Use when a fastener is missing, stripped, or corroded to help maintain stable, safe appliance operation. What it does:

• Secures panels, trim, brackets or other appliance parts to prevent looseness or movement.
• Replaces missing, worn, or damaged screws so components align and operate correctly.
• Helps reduce rattling, vibration noise, and gaps around doors or panels.
• Verify the exact size and thread before ordering to ensure proper fit.

• Disconnect power and water before starting any repair.
• Use the matching screw size and thread; do not force or overtighten.
• Start threads by hand to avoid cross-threading; use the correct screwdriver or bit.
• If threads or mounting holes are damaged, repair before reuse.

This replacement screw secures appliance panels and internal components so they stay aligned and rattle-free. Replace missing or stripped hardware to restore a tight, reliable fit and prevent looseness that can lead to noise or damage.

• Fastens panels, brackets, or components to the chassis as designed
• Helps reduce vibration, rattling, and gaps from loose or missing hardware
• Restores proper alignment when an original screw is lost or threads are damaged
• Maintains safe, secure mounting of the original assembly

• Disconnect power (and shut off gas/water if applicable) before servicing
• Replace in the same location and orientation as the original hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Transfer any original washer or clip if present

This replacement screw secures dishwasher components so they stay tight and aligned during operation. Use it to replace missing, rusted, or stripped hardware and restore a solid, rattle-free installation. What it does:

• Fastens compatible parts to the tub, frame, or internal assemblies
• Replaces worn or damaged screws to maintain proper mounting
• Helps reduce rattling or vibration from loose hardware
• Prevents shifting that can affect wash performance or cause leaks, depending on location

• 1 screw

• Disconnect power and shut off water before servicing
• Access the component being secured and remove the damaged or missing screw
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Match length and style to the original fastener for correct fit

This replacement latch mounting screw secures the refrigerator door latch assembly so the door closes and seals properly. Installing a fresh mounting screw restores a solid latch connection and reduces door movement or rattling. What it does:

• Fastens the door latch assembly to the cabinet or door frame
• Keeps the latch aligned so the door closes and seals correctly
• Prevents loose or wobbly latch hardware and related rattling noises
• Helps address symptoms like a door that won't stay latched or minor door play

• Turn off power to the appliance or unplug before working near electrical components
• Use the correct screwdriver and thread the screw straight to avoid stripping
• Do not overtighten — snug is sufficient to hold the latch without deforming parts
• Test the door operation after installation

This replacement door gasket creates a tight seal around the refrigerator door to help maintain proper temperature and reduce energy loss. It restores the seal where the original gasket is torn, warped, or no longer sealing. What it does:

• Seals the refrigerator door to keep cold air in and warm air out
• Helps prevent frost buildup and uneven cooling in the compartment
• Reduces energy use caused by a failing door seal
• Commonly used when the existing gasket is cracked, stretched, or no longer sealing

• Remove power to the appliance before starting any work
• Clean the door mating surface thoroughly before installing the new gasket
• Press the gasket into the door channel, starting at the top and working around the perimeter for an even fit
• If necessary, warm the gasket gently (per OEM guidance) to help it seat; avoid open flames or excessive heat

This hose clamp secures flexible water or drain hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal and helps stop drips or loose hoses. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to prevent leaks
• Restores a tight connection when original clamp is corroded, bent, or broken
• Helps eliminate water dripping, puddling, or intermittent leaks at hose joints
• Prevents hoses from slipping off during vibration or normal appliance use

• Disconnect power and shut off water supply before starting any repair
• Tighten clamp securely with pliers or the appropriate tool; avoid over-tightening which can damage the hose
• After installation, restore water and power, then check the connection for leaks

This is a genuine replacement mounting screw used to secure components in compatible Frigidaire appliances. It restores proper fastening so panels and parts stay aligned and stable during normal operation. What it does:

• Fastens appliance components, panels, or brackets to maintain secure assembly
• Replaces worn, stripped, or missing screws that cause rattling or loose parts
• Helps eliminate vibration-related noise by restoring correct fastening
• Matches OEM fit and function for reliable, long-lasting hold

• One replacement mounting screw, as pictured

• Use the proper size driver to avoid stripping the head; tighten until snug but do not overtighten
• Match screw location and length to the original for correct fit; keep any removed hardware for reference
• Disconnect power to the appliance before working in internal areas to reduce shock risk