Kenmore Dishwasher 665.13023K110 (66513023K110, 665 13023K110) Parts

This float assembly sits in the dishwasher tub and rises with incoming water to signal the float switch to stop filling. Replacing a worn or sticking overfill protector restores proper water level control and helps prevent overfilling and leaks.

• Monitors water level by floating upward as the tub fills
• Triggers the float switch to shut off the inlet valve at the correct level
• Helps prevent overfilling and potential leaks
• Helps with: won't fill or stops filling early, water level too high, float sticks or is visibly damaged

• Disconnect power and shut off the water supply before servicing.
• Remove the lower rack to access the float inside the tub.
• Lift the old float straight up; on some models a retainer under the tub must be released to remove it.
• Transfer any existing hardware if needed, install the new float, ensure free movement, then restore power and test for proper fill.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

A small metal clip that secures the appliance's ground wire to the chassis. Restores a reliable ground connection to reduce loose or arcing contacts and help prevent intermittent electrical faults. What it does:

• Secures the ground wire to the appliance frame to maintain a solid earth connection.
• Prevents a loose ground that can cause arcing, intermittent power issues, or visible sparking at the connection.
• Holds the wire in place through normal vibration and movement so terminals stay tight and stable.
• Replaces damaged, bent, or missing grounding fasteners to restore safe electrical continuity.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the clip.
• Use proper hand tools to remove and reinstall the screw or fastener that holds the clip—do not overtighten.
• Ensure the ground wire is routed and stripped correctly; replace wiring if insulation or conductor is damaged.

Replacement clip that secures the dispenser guard on compatible Whirlpool refrigerators. Replacing a damaged or missing clip restores a secure dispenser trim and can reduce rattling or misalignment around the dispenser area. What it does:

• Secures the dispenser guard/trim to the dispenser assembly to keep the trim aligned.
• Commonly needed when the guard is loose, rattling, cracked or falls out.
• Replaces broken or missing clips that allow the dispenser trim to move or vibrate.
• Helps restore proper fit of the dispenser trim so the dispenser components sit flush.

• Disconnect power (unplug or turn off the circuit) and shut off the water supply if working near the water/ice dispenser.
• Remove the dispenser trim or guard per the model's service instructions; handle plastic parts gently to avoid cracking.
• Align the clip with the mounting slot and engage until seated; if access is limited or the guard is damaged, follow safety guidelines when servicing appliances.

This tube nut secures the water inlet tubing to its fitting, creating a tight, leak-resistant connection. Use it when the original nut is cracked, stripped, or can no longer hold the line securely.

• Tightens over the inlet fitting to clamp the water tube and form a reliable seal
• Helps stop drips at the water-line connection point
• Addresses loose or damaged inlet connections and difficulty keeping the tube seated
• Commonly replaced when the nut is worn, cross-threaded, or visibly cracked

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Hold the fitting with one wrench while tightening the nut with another to avoid twisting components
• Do not overtighten; restore water and check for leaks after installation
• Inspect the tubing, ferrule/sleeve, and insert; replace if worn or damaged

This dishwasher circulation pump and motor drives wash water through the spray arms for effective cleaning. Replacing a failed wash motor restores strong spray pressure and consistent cleaning performance throughout the cycle.

• Circulates water through the spray arms to wash and rinse dishes
• Maintains proper flow and pressure from the sump to all spray arms
• Direct replacement for a seized, noisy, or non-running wash motor
• Common symptoms: poor cleaning, no spray action, or humming/buzzing during wash

• Disconnect power at the breaker and shut off water supply before servicing.
• Access is from the bottom/front; many models require removing the toe panel and/or sliding the dishwasher out.
• Connect the wiring, seat the pump seal fully in the sump, and lock the assembly in place per your model's procedure.
• After reassembly, run a brief fill-and-wash to check for leaks and proper spray action.

This factory fastener is a #10-16 screw used to secure appliance panels and components. Replacing worn or missing hardware restores a tight fit, helps prevent rattles, and keeps parts properly aligned for dependable operation.

• Secures brackets, panels, and covers to the cabinet or frame
• Replaces missing, stripped, or corroded mounting hardware
• Helps reduce vibration and rattling from loose mounts
• Correct 10-16 thread to match designated OEM mounting points

• Disconnect power and shut off water or gas supply before servicing
• Match the screw to the original location using your model's diagram
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This overfill switch monitors water level and signals the appliance to stop filling to help prevent overflows. Use it to restore correct water-level control when the original switch fails or malfunctions. What it does:

• Detects excess water and interrupts the fill cycle as a safety cutoff
• Works with the washer's control to maintain proper water level
• Common symptoms of a failing switch: continuous filling, overfilling, or water-level related error codes
• Can also cause cycles to stop or not advance if the machine thinks tank is overfilled

• One overfill control switch

• Disconnect power and water supply before servicing to avoid shock or flooding
• Typically located behind the control console or rear access panel
• Handle wiring connectors gently and secure all connections before testing

This inner door panel replaces the appliance's damaged interior door surface to restore proper fit, protect internal components, and improve appearance. It also restores structural support and helps keep insulation and inner glass secure for reliable operation. What it does:

• Replaces the door's interior panel that supports inner glass, insulation, and internal hardware.
• Protects wiring, controls, and insulation inside the door from damage and moisture.
• Addresses common symptoms like cracked or dented inner panels, rattling or loose-feeling doors, and visible gaps between door layers.
• Restores proper door fit and interior appearance after impact or wear.

• Disconnect power (and water supply if applicable) before starting work.
• Wear cut-resistant gloves and handle any glass or sharp edges carefully.
• Retain and reuse original fasteners when possible; align the panel before fully tightening screws.

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Size: 8-32 x 1/2 inch.

This inner vent gasket seals the dryer vent opening to direct hot air through the exhaust system and help maintain proper airflow. Replacing a worn or torn vent gasket restores a tighter seal and reduces air leaks. What it does:

• Seals the inner vent area to keep exhaust air flowing through the ductwork.
• Helps prevent air leaks that can cause longer dry times or uneven drying.
• Reduces lint escape and buildup around the vent opening.
• Restores proper airflow to help the dryer run more efficiently.

• Disconnect power to the appliance before starting any repair.
• Access typically requires removing panels or the drum—follow your model's service instructions.
• Inspect the mounting surface for damage or debris and clean before installing the new gasket.
• Ensure the gasket is seated evenly and not pinched during reassembly; test operation after installation.

This replacement lever operates the overflow/level switch assembly to help the washer detect and respond to water level changes. It restores the mechanical action that tells the control when the tub is full. What it does:

• Moves the overflow/level switch mechanism so the machine can sense water level correctly
• Helps address overfilling, continuous filling, or erratic fill behavior caused by a worn or broken lever
• Restores reliable engagement between the float/actuator and the switch
• Works as the mechanical linkage for the overflow/level sensing assembly

• Disconnect power and turn off the water supply before beginning service.
• Access typically requires removing the cabinet or control console; keep fasteners organized.
• Install the lever so it aligns with the switch actuator and float linkage; verify smooth movement after assembly.

This tab-sump mounting secures the dishwasher sump/dispenser area so detergent tabs and related components stay properly aligned. Replacing a worn or broken mounting restores correct dispenser positioning and helps prevent tabs from falling loose during cycles. What it does:

• Holds the tab/sump assembly in place to maintain proper detergent tab positioning
• Prevents the dispenser or sump from shifting or sagging during operation
• Helps reduce incidents of tabs dislodging or failing to stay seated
• Supports correct alignment of adjacent dispenser components

• Disconnect power and water supply before starting any repair
• Remove the door panel or access cover to reach the sump area
• Inspect surrounding clips and seals; replace any damaged fasteners for a secure fit