Kenmore Dishwasher 665.13102K902 (66513102K902, 665 13102K902) Parts

This motor-pump is the dishwasher drain pump assembly that removes water from the tub so cycles can complete. Replacing a failed pump restores proper draining and helps prevent standing water and cycle errors. What it does:

• Spins the impeller to pump wastewater out of the dishwasher during drain cycles
• Stops leaks and prevents water from remaining in the tub when working correctly
• Commonly linked to symptoms such as no draining, water left in the tub, or a humming noise during drain
• Works as the integrated motor and pump — not a separate impeller-only part

• Disconnect power and shut off water supply before starting any repair
• Handle with care to avoid damaging the impeller, seals, or electrical connector
• May require removing access panels or the dishwasher kickplate; use appropriate tools

This wire harness routes power and signals between the oven's controls and internal components to restore proper electrical connections and reliable operation. It replaces damaged, frayed, or corroded wiring that can cause intermittent function. What it does:

• Provides the factory routing and connector interfaces between control modules and internal oven components
• Restores lost or intermittent electrical connections that can cause nonresponsive controls or heating issues
• Replaces damaged insulation, broken wires, or melted connectors to reduce short and fire risk
• Maintains correct connector fit and secure wiring routing for reliable oven performance

• One complete wire harness as shown

• Disconnect all power to the appliance before beginning work to avoid electrical shock
• Handle connectors by the plug bodies; do not pull on wires when removing or seating connectors
• Route and secure the harness along factory clips and channels; avoid contact with heating elements or sharp edges
• Inspect connector terminals and mating components; replace or repair any additional damaged parts before reassembly

This thermostat bracket holds the oven or range thermostat securely in place, ensuring accurate temperature sensing and stable oven performance. Replaces a worn or broken bracket to restore proper thermostat positioning. What it does:

• Secures the thermostat assembly to the oven/range interior so the thermostat bulb or probe senses temperature correctly
• Prevents the thermostat from shifting or contacting heating elements
• Commonly replaced when the bracket is cracked, bent, or missing and causes temperature or control issues
• Helps reduce temperature inconsistencies caused by a loose or damaged mounting

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Handle the thermostat and sensor bulb carefully; avoid kinks or direct pressure on sensing elements
• Basic hand tools are typically required; verify part alignment before tightening fasteners

This dispenser cover (shield) replaces the plastic trim that surrounds a refrigerator's dispenser opening, restoring a clean finished look and helping direct water or ice into your cup. Fits where the dispenser meets the cabinet face. What it does:

• Covers and protects the dispenser opening, preventing chips and cosmetic damage
• Helps guide water and ice into cups for more accurate dispensing
• Hides internal dispenser components for a finished appearance
• Can reduce direct contact with moving dispenser parts

• One dispenser cover (shield)

• Remove power to the appliance before servicing to avoid electrical or injury risk
• Typically installs by snapping into place or fastening with a few screws; keep hardware if reusing
• Inspect surrounding trim for damage and replace any broken clips or screws for a secure fit

This adjuster is a replacement door/hinge adjustment component that restores proper door alignment and closing action for compatible appliances. It helps re-establish correct clearance and reduces rubbing, binding, or uneven gaps. What it does:

• Provides the adjustment point for proper door alignment and smooth operation
• Helps correct doors that sit unevenly, rub, or don't seal consistently
• Restores the ability to fine-tune door position after hinge or cabinet repairs
• Reduces noise and wear caused by misaligned doors or panels

• One adjuster as shown

• Turn power off and disconnect the appliance before starting any repair
• Some disassembly of the door, hinge, or trim may be required
• Keep fasteners and small parts organized; verify orientation before final tightening

Color: Bisque

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Supply Tube is an OEM component specifically designed for connecting Whirlpool brand dishwashers to home plumbing systems. It transports water into dishwashers for cleaning and rinsing cycles.  

Potential causes of a problematic supply tube include mineral deposits reducing flow or small punctures from prolonged vibrations.

Symptoms of a faulty water supply tube include:

• Water leaks inside or underneath the dishwasher
• Inadequate water pressure impacting clean performance

Compatible models include some brands produced by KitchenAid, Maytag, and Kenmore.

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This part is responsible for circulating water during the wash cycle and draining water at the end of the cycle.  

Causes of a bad assembly can include blockages from debris, electrical failures, or wear and tear from regular use.  

Symptoms of a bad Pump and Motor Assembly include:

• Dishes remaining dirty after a wash cycle
• Water not draining properly from the dishwasher
• Unusual noises during operation
• Error codes related to water flow or pump performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Volute with Seal is an OEM part for Whirlpool dishwashers. This part directs water flow within the dishwasher's pump, ensuring efficient circulation and pressure during the wash cycle. The seal helps to prevent leaks by maintaining a tight closure between the volute and other pump components.

Common causes of a bad volute with seal include wear and tear from regular use, damage from debris or hard water deposits, and seal degradation due to age or chemical exposure.

Symptoms of a bad Volute with Seal include:

• Water leaking from the pump area
• Decreased washing performance
• Unusual noises from the pump during operation
• Visible cracks or damage to the volute or seal

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

Located between console and door.

A small replacement door switch that tells the appliance when the door is closed so cycles can start—restores proper door-sensing to resolve no-start, intermittent operation, or control lockout issues related to a faulty door switch. What it does:

• Detects door open/closed state and completes the control circuit when the door is shut.
• Prevents the appliance from starting or running when the door is open.
• Commonly replaces a worn or broken switch that causes no-starts, stops mid-cycle, or intermittent operation.
• Works as the door-sensing safety/switching component in the door latch/closure assembly.

• Disconnect power (unplug or switch off breaker) before inspecting or replacing the switch.
• Match connector terminals and orientation to the original switch; secure wiring and terminals firmly.
• Inspect door latch and strike for damage or misalignment when replacing the switch.

Color: Stainless