Kenmore Dishwasher 665.13363K110 (66513363K110, 665 13363K110) Parts

This insulated wire lead carries electrical current between components, restoring reliable power routing in your appliance. It's a direct-replacement discrete wire used where a single conductor is required for safe operation. What it does:

• Provides a single insulated conductor to connect terminals or components
• Restores proper electrical continuity when a wire is damaged, burned, or disconnected
• Helps prevent shorts by maintaining insulation between conductors
• Suitable for low- to moderate-current wiring routes within the appliance

• One insulated wire lead as shown

• Disconnect power before inspecting or replacing wiring to avoid shock or injury
• Route the wire as the original, avoiding sharp edges and heat sources; secure with existing clips or ties
• Replace any damaged terminals, connectors, or fasteners; use correct crimps or solder joints per OEM practice

The Dishwasher Door Seal is an OEM replacement part for Whirlpool dishwashers. It provides a tight seal around the dishwasher door to prevent water, sound, and heat from escaping during the wash cycle. Measuring 71” in length (and stretching up to 75”), this door seal prevents water from leaking out during wash cycles.

Causes of a bad seal can include cracks, tears, or splits that develop due to regular use and age. Damage may also occur from over-tightening of the door or accidental impact.

Symptoms of a bad dishwasher door seal include:

• Water or moist air leaks around the door during a cycle  
• Higher energy bills due to hot air escaping
• Excess moisture or mineral deposits around the door seal area
• Food particles or debris trapped under a torn seal

This genuine OEM Whirlpool replacement seal is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This electronic control board is the appliance's central controller. It interprets user inputs and sensor signals to power components at the right time, restoring reliable operation when the original board fails.

• Interprets user settings and manages cycle timing and temperature control
• Switches relays/outputs to run motors, heaters, valves, fans, and lights
• Interfaces with sensors and safety switches to protect the appliance
• Symptoms can include no display or response, won't start, cycles that won't advance, or erratic operation
• Logs diagnostic error codes to aid troubleshooting

• Disconnect power before servicing; follow ESD precautions and handle the board by the edges
• Access the control area, then note/photograph wiring and move connectors one at a time to the new board
• Mount securely, ensure no wires are pinched, reassemble, and restore power
• Run a diagnostic or test cycle to confirm normal operation

This connector links mating components within the appliance to create a secure, reliable connection. Replacing a cracked or loose connector helps restore consistent operation and prevent intermittent issues caused by poor contact or separation. What it does:

• Creates a stable connection between mating parts or harnesses in the appliance
• Helps prevent looseness or separation that can disrupt performance
• Direct replacement for broken, brittle, or deformed connectors
• Can resolve intermittent operation traced to a poor connection at this junction

• 1 connector

• Disconnect power and, if applicable, shut off water before servicing
• Note orientation and positions before removal to ensure correct reassembly
• Seat the connector fully until any locking features engage; do not force
• Inspect mating parts for wear or damage and replace if necessary

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This spacer fits between tank components to maintain proper spacing and alignment, helping reduce vibration and wear. Use this genuine replacement to restore correct clearances and improve stability in the appliance's tank assembly. What it does:

• Positions and separates tank parts to maintain correct alignment during operation
• Helps reduce noise and vibration caused by misaligned components
• Prevents metal-to-metal contact that can cause premature wear or damage
• Restores factory clearances after service or replacement of tank parts

• One spacer

• Designed for direct replacement; use the OEM mounting location and orientation
• Disconnect power and water (if applicable) before beginning repair
• If fasteners or surrounding components are worn or damaged, replace them to ensure a secure fit

This replacement manifold routes water inside the appliance so spray arms and wash chambers receive the proper flow for cleaning. Replaces a worn or cracked manifold to restore proper water distribution and reduce leaks. What it does:

• Directs inlet water to spray arms and internal wash channels for normal wash cycles
• Helps maintain consistent water flow for effective cleaning performance
• Stops or reduces leaks when replacing a cracked or damaged manifold
• Resolves symptoms like weak or no spray, water pooling, or visible leaks

• One replacement manifold

• Install requires access to the appliance interior and removal of panels—disconnect power and water before starting
• Tighten fittings to manufacturer torque recommendations and check for leaks after installation
• Inspect related hoses, clamps, and seals and replace if brittle or damaged

A replacement control bracket that secures the console/control assembly to the appliance frame so buttons, knobs and the control board stay properly aligned. Restores stable mounting and reduces rattling or misalignment. What it does:

• Holds the control panel/console in the correct position on the appliance frame
• Keeps the control board and user interface securely mounted to prevent movement
• Helps eliminate rattling, vibration noise or intermittent contact caused by loose mounting
• Provides the proper mounting points for screws and other fasteners

• One control bracket

• Disconnect power to the appliance before beginning any repair
• Remove the console or trim as needed to access the bracket; keep all screws and fasteners
• Secure with the original fasteners; do not overtighten
• If the control board or wiring is exposed, handle electronics carefully and avoid contact with conductive tools

This clip is a small retainer used to secure panels, wiring, or hoses so components stay in place and operate quietly. It prevents loose parts from shifting during normal use and helps maintain appliance fit and finish. What it does:

• Holds wiring, harnesses, or small hoses in position to prevent rubbing or disconnection
• Keeps trim or access panels seated to reduce vibration and noise
• Helps maintain correct routing to avoid wear on wires and hoses
• Commonly replaced when the original clip is broken, cracked, or missing

• One clip

• Disconnect power to the appliance before attempting any repair
• Access the area and remove any panels or covers that block the clip location
• Press the clip into its mounting slot or snap the harness into the clip until it seats securely
• Replace any damaged surrounding fasteners or retainers; do not use damaged clips