Kenmore Dishwasher 665.13433K704 (66513433K704, 665 13433K704) Parts

The Filter Screen is an OEM component specifically designed for Whirlpool dishwashers. Located inside the sump area, the durable mesh screen captures small food particles and debris before wash water is recirculated through cycles.

Symptoms of a bad filter screen can include clogging obscuring openings over time, degrading mesh no longer inhibiting passage, or dislodging from mounting points allowing bypass.

Causes involve the normal accumulation of soils requiring periodic cleaning. Mineral buildup may eventually cement sections together reducing effectiveness. 

Symptoms of a bad filter screen include:

• Dirty or soiled wash water unable to fully circulate  
• Filth dispersing throughout the wash cabinet interior
• Reduced cleaning and unsatisfactory dish results

This OEM Whirlpool part is also compatible with KitchenAid, Maytag, Jenn-Air, Amana, and some Kenmore dishwasher models. Replace to maintain built-in wastewater filtration protecting major components.

This center basket lid secures the top of the washer basket and helps keep laundry contained during the wash and spin cycles. It replaces a cracked or missing lid to restore proper operation and reduce fabric snags. What it does:

• Covers the center of the tub/basket to keep clothes from catching on the agitator or basket edge
• Helps maintain balanced load containment during agitation and spinning
• Prevents small items from falling into the basket gap or drain area
• Restores the washer's intended interior protection and appearance

• One center basket lid

• Disconnect power and water supply before starting any repair
• Remove the dispenser/console or top panel only if required by your model; follow factory service instructions
• Handle replacement parts carefully to avoid scratching the tub or lid finish

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Supply Tube is an OEM component specifically designed for connecting Whirlpool brand dishwashers to home plumbing systems. It transports water into dishwashers for cleaning and rinsing cycles.  

Potential causes of a problematic supply tube include mineral deposits reducing flow or small punctures from prolonged vibrations.

Symptoms of a faulty water supply tube include:

• Water leaks inside or underneath the dishwasher
• Inadequate water pressure impacting clean performance

Compatible models include some brands produced by KitchenAid, Maytag, and Kenmore.

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This part is responsible for circulating water during the wash cycle and draining water at the end of the cycle.  

Causes of a bad assembly can include blockages from debris, electrical failures, or wear and tear from regular use.  

Symptoms of a bad Pump and Motor Assembly include:

• Dishes remaining dirty after a wash cycle
• Water not draining properly from the dishwasher
• Unusual noises during operation
• Error codes related to water flow or pump performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

A small replacement door switch that tells the appliance when the door is closed so cycles can start—restores proper door-sensing to resolve no-start, intermittent operation, or control lockout issues related to a faulty door switch. What it does:

• Detects door open/closed state and completes the control circuit when the door is shut.
• Prevents the appliance from starting or running when the door is open.
• Commonly replaces a worn or broken switch that causes no-starts, stops mid-cycle, or intermittent operation.
• Works as the door-sensing safety/switching component in the door latch/closure assembly.

• Disconnect power (unplug or switch off breaker) before inspecting or replacing the switch.
• Match connector terminals and orientation to the original switch; secure wiring and terminals firmly.
• Inspect door latch and strike for damage or misalignment when replacing the switch.

Color: Stainless

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Also order air vent seal