Kenmore Dishwasher 665.13849K601 (66513849K601, 665 13849K601) Parts

This front seal sits at the leading edge of the dishwasher door opening to keep wash water and steam contained. Replacing a worn seal helps stop front-edge drips and protects adjacent cabinetry and flooring.

• Creates a watertight barrier along the front tub-to-door interface
• Helps prevent leaks at the bottom/front of the door during cycles
• Replace if the seal is cracked, flattened, torn, or missing
• Common symptoms: water under the kick panel, damp streaks at the front lip, visible wear

• Disconnect power and turn off the water supply before servicing
• Open the door, remove the old seal, and clean the front lip/channel thoroughly
• Center and press the new seal fully into place without stretching; ensure even compression
• Close the door and run a short test cycle to check for leaks

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

A small metal clip that secures the appliance's ground wire to the chassis. Restores a reliable ground connection to reduce loose or arcing contacts and help prevent intermittent electrical faults. What it does:

• Secures the ground wire to the appliance frame to maintain a solid earth connection.
• Prevents a loose ground that can cause arcing, intermittent power issues, or visible sparking at the connection.
• Holds the wire in place through normal vibration and movement so terminals stay tight and stable.
• Replaces damaged, bent, or missing grounding fasteners to restore safe electrical continuity.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the clip.
• Use proper hand tools to remove and reinstall the screw or fastener that holds the clip—do not overtighten.
• Ensure the ground wire is routed and stripped correctly; replace wiring if insulation or conductor is damaged.

This retainer secures the FlexRow fold-down tine assembly on the dishwasher rack, keeping the row attached and stable so dishes stay where you position them. Replace a damaged or missing retainer to restore proper rack function.

• Holds the FlexRow tine row to the rack and supports correct up/down positioning
• Helps prevent the tine row from detaching or flopping during cycles
• Replace when cracked, worn, or missing
• Common symptoms: tines won't stay up, loose/misaligned row, items tipping over in the rack

• Disconnect power to the dishwasher before servicing
• Pull the rack forward; release and remove the damaged retainer
• Align and snap the new retainer onto the rack wires and FlexRow hinge until fully seated
• Inspect adjacent rack/tine parts for damage

This standpipe houses the washer's overfill control and directs excess water into the drain path, helping prevent overfilling and internal flooding. It's a direct-fit replacement for the factory overfill control housing. What it does:

• Provides the sealed channel for excess wash water to flow to the drain
• Supports and locates the overfill/level control assembly
• Helps stop water from overflowing the tub and causing leaks
• Can resolve symptoms like unexplained overfilling, water leaking at the washer base, or fill-level issues

• Disconnect power and shut off water before starting any repair
• Access may require removing the washer top or control housing
• Inspect surrounding gaskets and hoses for wear; replace if damaged
• Handle plastic components carefully to avoid cracking; test operation after reassembly

This sump tab secures the dishwasher's sump assembly to the tub opening, keeping it properly aligned and sealed. Replace a broken or missing tab to address movement, rattling, or leaks originating from the sump area.

• Locks the sump assembly to the tub/base opening
• Helps maintain the sump-to-tub seal to limit leaks
• Keeps the pump intake and fine filter area properly positioned
• Common symptoms: leaks under the unit, loose/shifted sump or filter, rattling/vibration from the sump area

• Disconnect power and water supply before servicing
• Access the sump per your model (from inside the tub by removing lower rack/filters, or from below after removing the toe panel)
• Ensure the sump and gasket are fully seated; install the new tab until it locks securely
• Run a brief fill/drain test and check for leaks before reassembly

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This dual BR2 positioner secures and aligns linked components so moving assemblies operate smoothly and reliably. Replaces a worn or broken positioner to restore correct part orientation and reduce misalignment-related issues. What it does:

• Holds and indexes two linked components to maintain correct alignment during cycles
• Helps prevent binding, noisy operation, or mis-positioned parts
• Restores proper mechanical engagement after breakage or wear
• Works as the mounting/locator piece that keeps assemblies in their intended position

• Disconnect power to the appliance before starting any repair
• Remove the appropriate access panels to reach the old positioner; keep fasteners organized
• Note wiring or linkage locations (take a photo) before removing the old part for proper reassembly
• Reinstall panels and restore power; test the appliance to verify correct operation

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Size: 8-32 x 1/2 inch.

This adjustable manifold is a direct-fit replacement that secures and positions the appliance's manifold assembly so related components line up and function correctly. It restores proper alignment and reliable operation when the original is bent or worn. What it does:

• Provides a mounting surface and adjustable position for the manifold assembly and attached components
• Helps maintain correct alignment so burners/valves operate smoothly
• Restores fit when the original manifold is damaged, bent, or loose
• Resolves symptoms such as uneven burner operation, ignition difficulty, or mechanical misalignment

• Turn off power and shut off gas supply before starting work
• Handle and align carefully to avoid bending; secure with the OEM fasteners
• Check seals and connections after installation; test operation per manufacturer instructions

This is a genuine 4-24 x 3/8 screw used to fasten trim and components on compatible appliance assemblies. It provides a secure, vibration-resistant connection so panels and parts stay properly aligned during use. What it does:

• Secures panels, brackets, or components to the appliance frame
• Helps prevent rattling or loosening from normal vibration
• Works with threaded or self-tapping holes sized for a #4-24 fastener
• Common replacement for stripped, rusted, or missing mounting screws

• Use the matching screwdriver or nut driver to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread damage
• Replace any corroded or damaged screws in sets when multiple fasteners show wear
• Disconnect power and follow appliance safety guidance before servicing

Color: Black

This dispenser cover (shield) replaces the plastic trim that surrounds a refrigerator's dispenser opening, restoring a clean finished look and helping direct water or ice into your cup. Fits where the dispenser meets the cabinet face. What it does:

• Covers and protects the dispenser opening, preventing chips and cosmetic damage
• Helps guide water and ice into cups for more accurate dispensing
• Hides internal dispenser components for a finished appearance
• Can reduce direct contact with moving dispenser parts

• One dispenser cover (shield)

• Remove power to the appliance before servicing to avoid electrical or injury risk
• Typically installs by snapping into place or fastening with a few screws; keep hardware if reusing
• Inspect surrounding trim for damage and replace any broken clips or screws for a secure fit