Kenmore Dishwasher 665.13966K010 (66513966K010, 665 13966K010) Parts

This sump and motor assembly replaces the lower tub sump with the circulation pump pre-installed. It restores proper water recirculation to the spray arms and a tight seal at the tub floor to help reduce leaks and noise.

• Circulates wash water through the spray arms for consistent cleaning performance
• Channels and filters water beneath the tub via the integrated sump
• Maintains a watertight seal at the tub base
• Common symptoms of failure: weak or no spray action, poor cleaning results, loud humming/grinding during wash, or water leaking from the center bottom area

• Disconnect power and turn off the water supply before servicing; allow internal components to cool
• Remove the lower rack, spray arm, and filters to access the sump; disconnect hoses and wiring, then release the locking tabs to remove the assembly
• Ensure all seals/O-rings are properly seated; fully engage hose and electrical connections to prevent leaks
• After installation, run a brief test cycle and inspect carefully for leaks before reassembling panels

Color: light grey. It measures about 2-1/2 inches high by 2 inches deep.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

This de-coupled drain housing creates a sealed, vibration-isolated connection in the appliance's drain path. Replacing a cracked or leaking housing restores reliable draining performance and helps prevent water leaks and rattling during the drain cycle.

• Forms the rigid, sealed connection between the drain path and mating components
• Isolates pump vibration from the chassis to reduce noise during drain
• Directs wastewater efficiently out of the unit during the drain cycle
• Common symptoms of a failed housing include standing water, leaks under the unit, loud vibration/buzzing while draining, or visible cracks/broken tabs

• Disconnect power and water supply before servicing; allow any hot water to cool
• Access the drain area and place a towel or pan to catch residual water
• Move clamps/hoses, then transfer any reusable seals or grommets; replace worn seals as needed
• Secure all connections and clamps; run a short test and check carefully for leaks

Includes two screws, two clamps, and undercounter mounting brackets.

This spray arm distributes wash water inside the dishwasher, rotating to deliver even spray coverage across the racks. Replace a cracked or clogged arm to restore consistent cleaning performance and reliable water distribution.

• Directs pressurized water through jet openings while spinning to wash dishes evenly
• Helps address symptoms such as poor cleaning results or uneven spray coverage
• Replace if the arm is cracked, warped, mineral-fouled, or no longer spins freely
• Damage or improper seating can cause the arm to strike dishes/tub and make noise

• Disconnect power to the dishwasher before servicing
• Remove rack(s) if needed; release the arm by unscrewing the retainer or pressing the locking tab (method varies by model)
• Clean debris from the mounting hub and seal surfaces before installing the new arm
• Seat fully, ensure the arm spins freely with proper clearance, then run a test cycle

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Drain hose (loop) that routes washer wastewater and forms a high drain loop to help reduce backflow and siphoning. Replaces cracked, kinked, or deteriorated drain hoses to restore proper draining and reduce leaks. What it does:

• Directs wastewater from the appliance to the household drain to maintain proper drainage.
• Forms a high drain loop to help prevent backflow and siphoning into the washer.
• Replaces worn or damaged hoses that can cause leaks, slow draining, or standing water.
• Works with the appliance's factory drain connection and clamps.

• Disconnect power and turn off the water supply before servicing.
• Route hose to create a high loop above the cabinet connection and secure with clamps to prevent kinks or sagging.
• Use appropriate clamps or fasteners and tighten connections; inspect for leaks after restoring power and water.

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

Insulation pad that fits behind appliance panels to restore thermal protection and reduce noise. Replacing a damaged or missing pad helps protect nearby wiring and components from heat and can reduce vibration-related rattling. What it does:

• Provides thermal insulation to help limit heat transfer to adjacent panels and components.
• Dampens vibration and reduces rattling or buzzing caused by loose or worn insulation.
• Protects wires, connectors and plastic parts from excess heat when installed correctly.
• Common symptom: missing, torn, or deteriorated pad with increased exterior heat or noise.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove access panels as needed; position the pad flat against the cabinet surface or mounting area.
• Use original clips/adhesive or manufacturer-recommended fasteners to secure the pad; avoid covering vents or controls.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This manifold is the OEM gas valve assembly that routes propane or natural gas from the regulator to the oven and burner valves so the appliance can ignite and heat properly. Designed as a direct-replacement service part. What it does

• Channels gas from the regulator to individual burner/oven valves so each burner can ignite.
• Replaces a worn or damaged manifold that can cause weak or no ignition.
• Addresses symptoms such as burners that won't light, oven failing to heat, or inconsistent flame across burners.
• Works with the appliance's existing regulator and control valves when installed correctly.

• Turn off gas supply and electrical power before attempting removal or service.
• Inspect fittings and gaskets; replace any damaged seals to prevent leaks.
• After installation, perform a gas-leak test and verify proper ignition and flame patterns.

This machine screw secures panels, brackets, and other components inside your appliance. Replacing a missing or damaged fastener restores a solid fit, reduces vibration and rattling, and helps keep assemblies properly aligned for reliable performance.

• 10-32 machine-thread fastener for mounting and securing internal parts and panels
• Helps maintain alignment and structural integrity of assembled components
• Replaces missing, stripped, or damaged hardware
• Reduces rattling, vibration, or loosening from worn fasteners

• Disconnect power; shut off gas or water supplies before servicing
• Match thread and length to the original fastener used in that location
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse original washers or clips if present and in good condition

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.