Kenmore Dishwasher 665.14063K010 (66514063K010, 665 14063K010) Parts

The Thermostat Housing is an OEM part for Whirlpool dishwashers. It encases the thermostat responsible for accurately monitoring water temperatures throughout cleaning cycles. 

Symptoms of a faulty housing include:

• Inconsistent or improper water heating  
• Delayed or incomplete cycles from temperature control issues
• Error codes or failure detection by the control board

Causes may involve cracks allowing steam penetration, loose mounting points compromising seals, or damaged seals leaking interior thermostat components. 

This OEM replacement fits Whirlpool, KitchenAid, Jenn-Air, and some Kenmore models as well.

This center basket lid secures the top of the washer basket and helps keep laundry contained during the wash and spin cycles. It replaces a cracked or missing lid to restore proper operation and reduce fabric snags. What it does:

• Covers the center of the tub/basket to keep clothes from catching on the agitator or basket edge
• Helps maintain balanced load containment during agitation and spinning
• Prevents small items from falling into the basket gap or drain area
• Restores the washer's intended interior protection and appearance

• One center basket lid

• Disconnect power and water supply before starting any repair
• Remove the dispenser/console or top panel only if required by your model; follow factory service instructions
• Handle replacement parts carefully to avoid scratching the tub or lid finish

The Dishwasher Door Seal is an OEM replacement part for Whirlpool dishwashers. It provides a tight seal around the dishwasher door to prevent water, sound, and heat from escaping during the wash cycle. Measuring 71” in length (and stretching up to 75”), this door seal prevents water from leaking out during wash cycles.

Causes of a bad seal can include cracks, tears, or splits that develop due to regular use and age. Damage may also occur from over-tightening of the door or accidental impact.

Symptoms of a bad dishwasher door seal include:

• Water or moist air leaks around the door during a cycle  
• Higher energy bills due to hot air escaping
• Excess moisture or mineral deposits around the door seal area
• Food particles or debris trapped under a torn seal

This genuine OEM Whirlpool replacement seal is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This fine screen is the small mesh filter that sits in the dishwasher sump to catch food particles and help protect the pump and wash system. It keeps debris from circulating so dishes rinse more effectively. What it does:

• Traps food and debris in the sump to prevent clogging and pump damage
• Helps maintain proper water flow for consistent wash and drain performance
• Reduces risk of food redepositing on dishes during cycles
• Commonly replaced when torn, heavily clogged, or missing

• One fine mesh sump screen

• Turn off power and disconnect the dishwasher before servicing
• Remove the lower dish rack and access the sump area to replace the screen
• Inspect surrounding seals and housing for damage while servicing
• No special tools typically required; handle mesh gently to avoid deformation

This replacement cap protects and seals a small appliance component to prevent debris entry and reduce wear. It restores the original fit and helps keep moving parts and seals working as intended. What it does:

• Covers and protects an exposed component or fitting to prevent dirt and moisture intrusion
• Maintains proper spacing and alignment for nearby parts
• Helps reduce rattling or contact noise from loose or worn ends
• Can prevent premature wear or minor leaks when used as intended

• Disconnect power and water before servicing the appliance
• Access the cap location by removing the adjacent panel or trim
• Press or snap the cap into place; use gentle, even pressure to avoid damage
• If the cap secures a sealed connection or seal, inspect nearby gaskets and replace if damaged

This disk valve diverter directs wash water flow between spray arms and wash zones to restore proper circulation and cleaning performance. It replaces a worn or damaged diverter to help return consistent spray pressure and distribution. What it does:

• Routes pump water to the correct spray arm or wash zone during the wash cycle
• Helps maintain even spray pressure for effective cleaning
• Worn or broken diverter can cause poor cleaning, reduced water to a spray arm, or unusual pump noise
• Prevents bypass flow that can reduce wash performance

• One disk valve diverter as shown

• Disconnect power to the appliance and shut off the water supply before starting
• Access may require removing the tub access panel or disassembling spray arm/tub components
• Inspect surrounding seals and gaskets; replace any damaged parts to prevent leaks
• After installation, run a short cycle and check for proper water routing and leaks

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This spacer fits between tank components to maintain proper spacing and alignment, helping reduce vibration and wear. Use this genuine replacement to restore correct clearances and improve stability in the appliance's tank assembly. What it does:

• Positions and separates tank parts to maintain correct alignment during operation
• Helps reduce noise and vibration caused by misaligned components
• Prevents metal-to-metal contact that can cause premature wear or damage
• Restores factory clearances after service or replacement of tank parts

• One spacer

• Designed for direct replacement; use the OEM mounting location and orientation
• Disconnect power and water (if applicable) before beginning repair
• If fasteners or surrounding components are worn or damaged, replace them to ensure a secure fit