Kenmore Dishwasher 665.14069K010 (66514069K010, 665 14069K010) Parts

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Size: 8-32 x 1/2 inch.

This is the rear wheel support for a dishwasher rack. It helps guide and support the rack as it slides in and out, restoring smooth movement and preventing the rack from binding or derailing.

• Supports and guides the rack at the rear during opening/closing
• Helps correct issues like a wobbly, sticking, or misaligned rack
• Can address noisy, rough rack travel caused by a worn support
• Maintains proper rack tracking to reduce derailment

• Disconnect power and water before servicing
• Pull rack forward to access the rear support area
• Depress locking tabs/retainer to remove the old support; press-fit the new support until secure
• Verify smooth rack travel before returning the appliance to service

This tab-sump mounting secures the dishwasher sump/dispenser area so detergent tabs and related components stay properly aligned. Replacing a worn or broken mounting restores correct dispenser positioning and helps prevent tabs from falling loose during cycles. What it does:

• Holds the tab/sump assembly in place to maintain proper detergent tab positioning
• Prevents the dispenser or sump from shifting or sagging during operation
• Helps reduce incidents of tabs dislodging or failing to stay seated
• Supports correct alignment of adjacent dispenser components

• Disconnect power and water supply before starting any repair
• Remove the door panel or access cover to reach the sump area
• Inspect surrounding clips and seals; replace any damaged fasteners for a secure fit

This Barrier protects and separates appliance components, keeping wiring and parts properly aligned for reliable operation. It's a simple, durable replacement that restores the original spacing and support inside the appliance. What it does:

• Provides a stable mounting/separation surface to prevent rubbing or contact between parts
• Helps maintain correct component alignment to reduce vibration and noise
• Prevents wiring or small parts from contacting hot or moving components
• Common symptom: visible cracks, breaks, or shifted parts where components no longer sit securely

• One barrier as shown

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove any panels or covers that block access; keep track of fasteners
• This part typically installs with screws or snap-fit tabs—do not force components

This plate-latch strike secures the appliance door by engaging the latch assembly so the door stays closed during operation. It replaces a worn or damaged strike to restore proper door closure and reliable operation. What it does:

• Provides a sturdy contact point for the door latch to engage and hold the door closed
• Helps prevent the door from popping open during use, which can cause cycle interruption
• Addresses symptoms like a door that won't stay latched, won't close fully, or causes the unit to stop mid-cycle
• Works as the mating strike for the existing latch assembly to ensure proper alignment

• One plate-latch strike

• Disconnect power to the appliance before beginning any repair
• Access the strike by opening the door; remove any trim or screws as needed to reach the strike mounting location
• Install replacement in the same orientation as the original and tighten fasteners securely without over-torquing
• After installation, verify the door latches smoothly and the appliance completes its normal cycle

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

This spacer positions and supports the appliance tank/tub assembly to maintain proper alignment and spacing for reliable operation. Replaces a worn or damaged spacer to restore correct fit and reduce movement. What it does:

• Keeps the tank/tub assembly correctly spaced and aligned with the cabinet and mounting points
• Helps prevent rubbing, binding, and excess vibration caused by a missing or damaged spacer
• Restores proper clearance to support seals and hoses that rely on correct tank positioning
• Useful when reassembling the appliance after service or repair

• One spacer

• Disconnect power and water supply before starting any repair
• Access may require removal of outer panels, console, or access covers depending on model
• Handle parts carefully to avoid damaging surrounding seals and wiring; reuse fasteners unless replacement is specified

This control bracket secures the console or control housing to the appliance, keeping the control panel stable and properly aligned for reliable operation. Replaces a damaged or missing bracket to restore secure mounting and prevent panel movement. What it does:

• Mounts the control console to the appliance frame to prevent wobbling or sagging
• Keeps control buttons and switches aligned for consistent user operation
• Helps stop rattling or vibration noise caused by a loose control housing
• Supports wiring and components behind the console to reduce strain on connectors

• Always unplug the appliance or disconnect power before beginning service
• Remove the console or access panel per service instructions to reach mounting points
• Use appropriate screwdrivers or nut drivers; keep original hardware unless damaged
• Align bracket and tighten screws evenly; avoid overtightening to prevent stripping

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.